LARK 85405 LED Chandelier Instruction Manual

LARK 85405 LED Chandelier

Product Specifications

• Model Number: 85405
• Indoor/Outdoor Use : Indoor
• Number of Bulbs : 2
• Fixture Type: Flush Mount
• Power Supply: Electric

Product Usage Instructions

Indoor Fixture Installation

1. Connect positive supply wire (typically black) to positive
   fixture lead.

2. Connect negative supply wire (ly white) to negative typical
   fixture lead.

3. Refer to grounding instructions for completing electrical
   connections.

Outdoor Fixture Installation

1. Connect positive supply wire (typically black) to positive fixture lead.
2. Connect negative supply wire (ly white) to negative typical fixture lead.
3. Use silicone sealant to cover connectors for a watertight seal.
4. If wall mounting, seal gaps with caulk to prevent water ingress.

Flush Mount Fixture Grounding
For positive grounding in a 3-wire electrical system, attach the fixture ground wire to the mounting strap with the ground screw.

Mounting Instructions

• Item No: 85405

1. Find a clear area in which you can work.
2. Unpack fixture from carton
3. Carefully review instructions before assembly.

Stem Install

1. Determine the desired height at which the pendant will be installed
2. The fixture is supplied with assorted stem sizes. Determine what combination of stems is needed to achieve the desired length.
3. Slip stems over wire and thread first stem onto top of pendent, longest stem first. Repeat the process until all required stems are threaded together.
4. After the last stem is threaded on take the canopy with the swivel and lacewire through the center hole in the swivel slip along the wire and thread the swivel into the top of the last stem.

Fixture Mounting

1. Prepare mounting strap (B) for mounting by installing screws (A) in mounting plate (B) – see Drawing 2.
   • Be sure the holes into which the screws are threaded match the spacing of holes (C) in the canopy (4).
2. Attach mounting plate (B) to junction box (J), using screws (G) NOT provided, and slip supply wires throughlarge the center hole in mounting plate (B).
3. Now adjust screws (A) so the screw will extend 3/16″ past the face of the canopy when the canopy is flush against the ceiling. after the screws are adjusted tighten the hex nut (H) to lock the screws in place.
4. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (IS 18) and follow all instructions to make all necessary wiring connections.
5. Hold the fixture towards the ceiling and slip mounting holes (C) in the canopy (4) over screws (A).
6. Secure the canopy by threading barrel knobs (D) onto screws (A).

SAFETY WARNING
READ WIRING AND GROUNDING INSTRUCTIONS (IS-18) AND ANY ADDITIONAL DIRECTIONS. TURN OFF POWER SUPPLY DURING INSTALLATION. IF NEWWIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. Lamp fixture with correct medium base bulb (2)
2. Place glass (1) into the socket and turn to lock into place
3. The fixture can now be powered on

I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Wiring Instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on connector — see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal.
   • If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

FAQ

(Frequently Asked Questions)

• Q: Can I use a different bulb type with this fixture?
  • A: It is recommended to use the correct medium base bulb specified for this fixture for optimal performance and safety.
• Q: Do I need to consult an electrician for installation?
  • A: If new wiring is required or if you are unsure about any electrical connections, it is advisable to consult a qualified electrician or local authorities to ensure compliance with electrical codes.

LARK 33000 PIN OAK PARKWAY, AVON LAKE, OHLARK 33000 PIN OAK PARKWAY, AVON LAKE, OH 44012 44012 LarkLiving.com

References

• Lark Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>