reolink RLC-810WA 4K Outdoor Wi-Fi Camera Instruction Manual

: June 17, 2024
: reolink

Table of Contents

reolink RLC-810WA 4K Outdoor Wi-Fi Camera
What’s in the Box
Camera Introduction
Mount the Camera
Install the Camera
Specifications
Notification of Compliance
Correct Disposal of This Product
Limited Warranty
Terms and Privacy
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

reolink RLC-810WA 4K Outdoor Wi-Fi Camera

reolink-RLC-810WA-4K-Outdoor-Wi-Fi-Camera-PRODUCT

Specifications

Model: RLC-810WA, RLC-811WA
Camera Features:
microSD Card Slot
Antenna
Mount
Metal Aluminum Case
Daylight Sensor
IR LEDs
High Definition Lens
Spotlight
Built-in Mic
Speaker
Network Port
Reset Button (press for 10 seconds to restore factory settings)
Power Port
WiFi Operating Frequency:
2.4 GHz EIRP < 20dBm
5 GHz EIRP < 23dBm
5.8GHz EIRP < 14dBm

Mount the Camera

Installation Tips
NOTE: There are two different types of mounts for bullet cameras. Please check out the mount included in the package and follow the corresponding instruction to install the camera properly.

What’s in the Box

$reolink-RLC-810WA-4K-Outdoor-Wi-Fi-Camera- $2$$

Camera Introduction

Model: RLC-810WA

microSD Card Slot
*Loosen the screwswith a screwdriver (not included) to access the microSD card slot.
Antenna
Mount
microSD Card Slot microSD Card Slot
Metal Aluminum Case
Daylight Sensor
IR LEDs
High Definition Lens
Network Port
Spotlight
Reset Button
Built-in Mic
Press for about 10seconds to restore the device to factory settings.
Power Port Speaker

Model: RLC-811WA

microSD Card Slot
*Loosen the screwswith a screwdriver (not included) to access the microSD card slot.
Antenna
Mount
microSD Card Slot microSD Card Slot
Metal Aluminum Case
Daylight Sensor
IR LEDs
High Definition Lens
Network Port
Spotlight
Reset Button
Built-in Mic
Press for about 10seconds to restore the device to factory settings.
Power Port Speaker

$reolink-RLC-810WA-4K-Outdoor-Wi-Fi-Camera- $5$$

Mount the Camera

Installation Tips

Do not face the camera towards any light sources.
Do not point the camera towards a glass window. Or, it may result in poor image quality because of the window glare by infrared LEDs, ambient lights or status lights.
Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image quality. To ensure best image quality, the lighting condition for both the camera and the capture object shall be the same.
To ensure better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
Make sure the power ports are not directly exposed to water or moisture and not blocked by dirt or other elements.
With IP waterproof ratings, the camera can work properly under conditions like rain and snow. However, it doesn’t mean the camera can work underwater.
Do not install the camera at places where rain and snow can hit the lens directly.
The camera may work in extreme cold conditions as low as -10°C. Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it outdoors.

NOTE: There are two different types of mounts for bullet cameras. Please check out the mount included in the package and follow the corresponding instruction to install the camera properly.

Install the Camera

Drill holes in accordance with the mounting hole template.

NOTE: Use the drywall anchors included in the package if needed. Install the mount base with the mounting screws included in the package.
NOTE: Run the cable through the cable notch on the mount base.

Failed to Upgrade the Firmware
If you fail to upgrade the firmware for the camera, try the following solutions:

Check out the current camera firmware and see if it is the latest one.
Make sure that you download the correct firmware from Download Center.
Make sure that your PC is working on a stable network.

If these won’t work, contact Reolink Support .

Specifications

General
Operating Temperature:
-10°C to 55°C (14°F to 131°F)
Operating Humidity: 10%-90%
RLC-810WA Size: Φ67 x 187mm
RLC-811WA Size: 80 x 72 x 238mm
(Weight: 485.7g, for RLC-810WA)
Weight: 862.9, for RLC-811WA)

Notification of Compliance

FCC Compliance Statements
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Compliance Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radiation Exposure statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

CE Declaration of Conformity

Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and Directive 2014/30/EU.

UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Radio Equipment Regulations 2017 and Electromagnetic Compatibility Regulations 2016.

WiFi Operating Frequency

OPERATING FREQUENCY : 2.4 GHz EIRP < 20dBm
5 GHz EIRP < 23dBm 5.8GHz EIRP < 14dBm

The functions of Wireless Access Systems including Radio Local Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are restricted to indoor use only within all European

Union countries (BE/BG/CZ/DK/DE/EE/IE/EL/ES/FR/HR/ IT/CY/LV/LT/LU/HU/MT/NL/AT/PL/PT/RO/SI/SK/FI/SE/TR/N O/CH/IS/LI/UK(NI)

Correct Disposal of This Product

This marking indicates that this product should not be disposed with other household wastes. throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.