LARK 83077BK Light 36 inch LED Chandelier Instruction Manual

LARK 83077BK Light 36 inch LED Chandelier

Product Specifications:

• Brand: Lark
• Model: 33000
• Item Number: 83077
• Location: Indoor Use Only

Product Usage Instructions

Assembly – Drawing 1:

1. Find a clear area to work in.
2. Unpack the fixture and glass from the carton.
3. Review the instructions carefully before assembly.
4. Determine the desired height for pendant installation.
5. Use assorted stem sizes to achieve the desired length as per Drawing 1.
6. Thread stems onto wire and attach them to the pendant, starting with the longest stem first.
7. Thread wire through the center hole of the canopy swivel and attach it to the top of the last stem.

Mounting – Drawing 2:

1. Prepare mounting strap (B) by installing screws (A) into mounting plate (B) as shown in Drawing 2.
2. Attach the mounting plate (B) to the junction box (J) using screws (G) and pass supply wires through the center hole.
3. Follow wiring and grounding instructions (I.S. 18) for electrical connections.
4. Hang the fixture by placing the canopy (D) over screws (A) and securing it with barrel knobs (E).

Arm Adjustment – Drawing 3:

1. Adjust the fixture arms as needed for your setup.

Frequently Asked Questions

Q: What should I do if I need new wiring during installation?

A: If new wiring is required, consult a qualified electrician or local authorities for code requirements before proceeding with installation.

Q: How should I connect the fixture’s wires to the supply wires?

A: Connect the positive supply wire (typically black) to the positive fixture lead and the negative supply wire (typically white) to the negative fixture lead using appropriately sized twist-on connectors. Refer to Drawings 1 and 2 for guidance.

Mounting Instructions

1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.

Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.• DO NOT restore current – either by fuse, breaker, or switch – until the new fixture is completely wired and in place.

1. Determine the desired height the pendant will be installed.

2. The fixture is supplied with assorted stem sizes. Determine what combinations of stems are needed to achieve desired length – see Drawing 1.

3. Slip stems over wire and thread first stem onto top of pendant, longest stem first.
   Repeat this process until all required stems are threaded together.

4. Slip wire through center hole of canopy swivel and thread swivel onto the top of the last stem installed.

5. Prepare mounting strap (B) for mounting by installing screws (A) into mounting plate (B) – see Drawing 2.

Be sure the holes into which the screws are threaded match the spacing of holes (C) in the canopy (D).

2. Attach mounting plate (B) to junction box (J), using screws (G) NOT PROVIDED, and slip supply wires through large center hole.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete installation of this fixture.

1. Hang the fixture by slipping canopy (D) over screws (A) and holding in position – see Drawing 2.
2. Thread barrel knobs (E) onto end of screws (A) and tighten to secure fixture to ceiling.
   NOTE: Fixture arms can be adjusted as shown in drawing 3

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1.  Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).

3. Cover open end of connectors with silicone sealant to form a watertight seal.
   If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.

4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

LARK 33000 PIN OAK PARKWAY, AVON LAKE, OH 44012 LarkLiving.com

References

• Lark Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>