HEADRUSH HRB 5028 True Wireless Earbuds Instruction Manual

HEADRUSH HRB 5028 True Wireless Earbuds Instruction Manual

INTRODUCTION

Thank you for purchasing the HRB 5028 true wireless earbuds. In order to maximize your listening experience please read the following instructions.

1. Earbuds LED indicator/microphone
2. MFB (Multi-function button)
3. Charging case LED indicator
4. USB-C charging port

Additional large and small earbud tips included (medium tips installed on earbuds).

WHAT’S INCLUDED

• HRB 5028 Earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual

OPERATING INSTRUCTIONS

Prior to first use, remove the plastic battery isolator tab located between the earbuds and charging case.

NOTE: The function compatibility may vary among different smartphones or devices. Not all functions are available on all devices.

CHARGING THE CASE

Use the included charging cable to fully charge the case before first use. It will take approximately 2.5 hours to fully charge.

• The blue LEDs will flash while the case is charging (and then stay on depending on the case charge)
• The 4 blue LEDs will stay ON after the case has charged and then turn off after a period of time.

CHARGING THE EARBUDS

The earbuds will automatically power OFF and begin charging when they are placed in the charging case. The white LED will turn ON to indicate the earbuds are charging and turn OFF when charging is complete. It will take 1.5 hours to fully charge the earbuds. The earbuds can be charged 3 times using a fully charged case.

NOTE: During use, the white LED on the earbuds will flash twice and beep once to indicate their battery level is low. Please charge the earbuds.

PAIRING

The earbuds will automatically enter Bluetooth® pairing mode when used for the first time. The left and right earbuds connect to each other.

• Remove both earbuds from the charging case. The earbuds will beep and the blue LED will flash 3 times to indicate the earbuds have powered ON
• Follow the instructions and enter “0000” as PIN, if required
• When the earbuds are successfully paired the blue LEDs will flash every 10 seconds
• After initial pairing, the earbuds will automatically turn ON and connect to your device when removed from the charging case, provided both earbuds and your Bluetooth® are ON and within range.
• If the earbuds are already paired to a device, the MFB has to be pressed 3 times to put them into pairing mode so they can be paired to another device. The white and blue LEDs will flash and the earbuds will beep to indicate they have paired. Turn Bluetooth® ON in your device settings and select “HRB 5028”

TO USE ONLY THE LEFT OR RIGHT EARBUD

If both earbuds are turned ON and paired to your device, you can return the right or left earbud to the charging case and the earbud (R or L) in your ear will continue to play. To use the right or left earbud only, remove it from the charging case. It will turn on and connect automatically to your device.

CLEAR PAIRED MEMORY

The earbuds retain a paired memory. If you have removed “HRB 5028” from your device, you will need to erase the paired memory before adding both earbuds back to your device.

To clear the paired memory:

• Turn Bluetooth® OFF in your device’s settings
• Put both earbuds in the charging case.
• When the white LEDs are ON, press and hold the MFB button on each earbud until each LED flashes
• Remove the earbuds from the case, they will flash blue. One earbud will stop flashing and the other will start flashing white/blue quickly
• Return both earbuds to the case to complete the process

OPERATION

• While playing music press either MFB button to pause, press again to resume. Press the right MFB twice for the next song, press the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an incoming call. Press either MFB button once to answer the call, press and hold to reject the call
• To disconnect from your device while still wearing both earbuds and are not listening to music or having a phone conversation:
  • Press and hold either MFB for 5 seconds. The earbuds will beep and power OFF

WARNING!

• Supervise children when using equipment, this product is not a toy
• Listening to earbuds at high volume levels, particularly over extended periods of time may damage your hearing
• If you have a pacemaker or other electrical medical devices, you should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the earbuds may cause clicks which at high volume setting may affect your hearing. Therefore, always set the volume control to minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard. This product is not intended for use by small children and should be kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose of batteries in fire to prevent an explosion

TROUBLESHOOTING

Problems Pairing

• If there is a problem with TWS or the Bluetooth connection, refer to the cleared paired memory and reset section

No sound

• Please check the volume on your audio device to make sure it is outputting sound
• Return the earbuds to the case and then remove them again if there are any connection issues

The earbuds are not fitting comfortably

• Please switch out the earbud tips to a different size to find the appropriate fit

Improving the Sound

• Sound can sometimes be improved by moving to a larger eartip size. The eartips still need to fit comfortably in your ear

CLEANING

Your earbuds may require periodic cleaning. Remove the tips from the earbuds and wash them with a mild detergent and water. Make sure the tips are dry before putting them back on the earbuds.

IMPORTANT SAFETY INFORMATION

CAUTIONS

• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product

SPECIFICATIONS

EARBUDS

Bluetooth® version: V5.0
Bluetooth® profiles: A2DP Profile v1.3/AVRCP Profile V1.6/OS Battery State
Wireless range: 10m (32ft.)
Playback time: Approx. 3 hours
Standby time: Approx. 4 days
Rated input:

Earbuds: DC 5V, 40mA
Charging case: DC 5V, 500mA

Driver diameter: 6mm
Sensitivity: 98dB
Frequency response: 20Hz-20kHz
Impedance: 16Ω
Battery: Polymer Lithium

CHARGING CASE

Input: DC 5V, 500mA
Output: DC 5V, 250mA

A2DP=Advanced Audio Distribution Profile, AVRCP=Audio Video Remote Control Profile, HFP-Hands-free Profile.
Approximate playback time, battery life depends on individual use and may be more or less than specified.
Bluetooth® connected, power ON, no music playing.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other trademarks and trade names are those of their respective owners.

FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada.
IC: 255A-8086997

RF EXPOSURE COMPLIANCE
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Imported by:
The Source, Barrie, Ontario, Canada, LAM 4W5
Manufactured in China
www.thesource.ca
© 2020 The Source. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>