HEADRUSH HRB 3032 True Wireless Earbuds Instruction Manual

HEADRUSH HRB 3032 True Wireless Earbuds

INTRODUCTION

Thank you for purchasing the HRB 3032 true wireless earbuds. In order to maximize your listening experience please read the following instructions.

1. Charging pins
2. Charging case LED indicator
3. USB-C charging port
4. MFB (Multi-function button)
5. Earbuds LED indicator
6. Charging contact point Ear tips

Additional large and small earbud tips included (medium tips installed on earbuds).

WHAT’S INCLUDED

1. HRB 3032 earbuds
2.  Charging case
3. Small, medium and large earbud tips
4. USB-C charging cable
5. Instruction manual

OPERATING INSTRUCTIONS

button once to answer the 2nd call and put the 1st call on hold.
End current call, answer first call| Press and hold either MFB button for 2 seconds.
Turn off earbuds (without putting them in charging case)| Press and hold either MFB button for 5 seconds.

Prior to first use, remove the plastic battery isolator tabs located on the earbud charging pins.

NOTE: The function compatibility may vary among different smartphones or devices. Not all functions are available on all devices.

FIT

We recommend that you try each ear tip (small, medium and large), then perform a sound check and choose the combination that provides the best sound experience.

CHARGING THE CASE

Use the included charging cable to fully charge the case before first use. It will take approximately 1.5 hours to fully charge. The blue LEDs will flash during charging, and remain ON when charging is complete.

1. LED ON indicates power level is lower than 25%.
2. LEDs ON indicates power level is between 25%~50%.
3. LEDs ON indicates power level is between 50%~75%.
4. LEDs ON indicates power level is between 75%~100%. NOTE: To check the remaining case battery power when it is not charging, please open the case lid and take out the earbuds.

CHARGING THE EARBUDS

1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case. The LED indicator will flash white when the earbuds are charging and will turn OFF when charging is complete.

NOTE: Remove the plastic battery isolator tabs located on the earbud charging pins. When the earbuds are paired to an Android™ or iOS device, the remaining earbud battery power will show on the device display.

PAIRING

The earbuds will automatically enter Bluetooth pairing mode when used for the first time. The left and right earbuds connect to each other.

1. Open the lid of the charging case and take the earbuds out. The earbuds will automatically turn ON. The LED will flash white and blue and the earbuds will beep to indicate that they have entered pairing mode.
2. Select “HRB 3032” on the Bluetooth device list to pair the earbuds automatically.
3. The earbuds will beep when Bluetooth is successfully connected.
4. After initial pairing, the earbuds will automatically turn ON and connect to your device when removed from the charging case, provided both earbuds and your Bluetooth are ON and within range.
5. The earbuds will automatically turn OFF after 6 minutes if no connection is established.

TO USE ONLY THE LEFT OR RIGHT EARBUD

If both earbuds are turned ON and paired to your device, you can return the right or left earbud to the charging case and the earbud (R or L) in your ear will continue to play. To use the right or left earbud only, remove it from the charging case. It will turn ON and connect automatically to your device.

RESET

If the left and right earbuds do not connect to each other, you will need to reset the earbuds and clear paired memory.

1. Remove “HRB 3032” from your device and turn Bluetooth OFF on your device.
2. Put both earbuds back into the charging case, then press and hold both MFB buttons for 5 seconds.
3. The blue LED will flash 3 times. This indicates that the reset procedure has been completed.
4. Turn Bluetooth back ON in your device settings and select ‘’HRB 3032”

OPERATION

1. If the earbuds were paired to your device previously, take the earbuds out of the charging case. The earbuds will power ON and connect to your device automatically
2. If the earbuds are not in the charging case and have powered OFF, press and hold both MFB buttons for 2 seconds to power ON
3. While playing music, press either MFB button to pause, press again to resume
4. Press and hold the right MFB button for 2 seconds for the next song, press and hold the left MFB button for 2 seconds for the previous song
5. The music will pause and the earbuds will ring when there is an incoming call. Press either MFB button once to answer the call, press and hold to reject the call
6. To turn the earbuds OFF without returning them to the charging case, press and hold either MFB button for 5 seconds. The white LEDs will flash 3 times and power OFF

WARNING!

1. Supervise children when using equipment, this product is not a toy
2. Listening to earbuds at high volume levels, particularly over extended periods of time may damage your hearing
3. If you have a pacemaker or other electrical medical devices, you should consult your physician before using this product
4. The operation of switching on your Hi-Fi system or plugging in the earbuds may cause clicks which at high volume setting may affect your hearing. Therefore, always set the volume control to minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earbuds
5. DO NOT use earbuds while driving or cycling
6. The small parts included with this product can be a choking hazard. This product is not intended for use by small children and should be kept away from children under 3 years of age
7. If not used for long periods, it is recommended to charge the earbuds and case at least every 3 months
8. Please dispose of rechargeable batteries properly. DO NOT dispose of batteries in fire to prevent an explosion

TROUBLESHOOTING

No sound

1. Please check the volume on your audio device to make sure it is outputting sound

Connection Problems

1. Please return the earbuds to the case and then remove them again if there are any connection issues
2. Refer to the cleared paired memory and reset section The earbuds are not fitting comfortably
3. Please switch out the earbud tips to a different size to find the appropriate fit

Improving the Sound

1. Sound can sometimes be improved by moving to a larger eartip size. The eartips still need to fit comfortably in your ear

CLEANING

Your earbuds may require periodic cleaning. Remove the tips from the earbuds and wash them with a mild detergent and water. Make sure the tips are dry before putting them back on the earbuds.

IMPORTANT SAFETY INFORMATION CAUTIONS

1. Keep in a safe place free from dust, liquid and extreme temperatures
2. DO NOT attempt to disassemble the product
3. DO NOT use chemicals to clean the product

SPECIFICATIONS EARBUDS

1. Bluetooth® version: V5.0

2. Bluetooth® profiles*: HSP;HFP;A2DP;AVRCP

3. Wireless range: 10m (32ft.)

4. IP rating: IPX4

5. Playback time: Approx. 4 hours**

6. Number of charges from case: 2

7. Charging time: Approx. 1.5 hours

8. Standby time: Approx. 55 hours

9. Rated input: DC 5V/45mA

10. Driver diameter: 6mm

11. Sensitivity: 92dB±3dB

12. Frequency response: 20Hz-20kHz

13. Impedance: 16Ω±15%

14. Battery: Polymer Lithium

15. Battery Capacity: 45mAh
    CHARGING CASE

16. Rated input: DC 5V, 500mA

17. Output: DC 5V, 300mA

18. Battery capacity: 350mAh

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other trademarks and trade names are those of their respective owners.

INDUSTRY CANADA NOTICE RSS247

This device complies with Industry Canada license-exempt RSS standards(s). Operation is Subject to the following two conditions:

1. This device may not cause interference, and this device must accept any interference,including interference that may cause undesired operation of the device
2. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada.

ISED REGULATORY COMPLIANCE

This device contains licence-exempt transmitters that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference
2. This device must accept any interference, including interference that may cause undesired operation of the device

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. IC:255A-8093127 CAN ICES-003(B)/NMB-003(B)

THE SOURCE – WARRANTY

The Source warrants that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of purchase. Within this period, simply take the product and your proof of purchase to any The Source store or participating dealer and the product will be replaced (where available) without charge. Any product which has been subject to misuse or accidental damage is excluded from this warranty. This warranty is only applicable to a product purchased through The Source company-owned stores or participating dealers in Canada where the warranty is included with the product. While this warranty does not confer any legal rights other than those set out above, you may have additional statutory rights which will vary under the laws of the various countries, states, provinces and other governmental entities in which The Source operates. This warranty is subject to all statutory rights you may have in Canada.

1. Imported by:
2. The Source, Barrie, Ontario, Canada, L4M 4W5
3. Manufactured in China
4. www.thesource.ca
5. © 2021 The Source. All rights reserved.

References

• La Source | Computers, Tablette et jeu, TV et audio

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>