HEADRUSH HRB 5035 True Wireless Earbuds Instruction Manual

HEADRUSH HRB 5035 True Wireless Earbuds

INTRODUCTION

Thank you for purchasing the HRB 5035 true wireless earbuds. In order to maximize your listening experience please read the following instructions .

1. Charging pins
2. Charging case LED indicator
3. USB-C charging port
4. MFB (Multi-function button)
5. Earbud LED indicator
6. Charging contact point
7. Ear tip

Additional large and small earbud tips included (medium tips installed on earbuds).

WHAT’S INCLUDED

• HRB 5035 earbuds
• Charging case
• Small, medium and large earbud tips
• USB-C charging cable
• Instruction manual

OPERATING INSTRUCTIONS

Prior to first use, remove the plastic battery isolator tabs located on the earbud charging points.

buttons for 2 seconds.
Power OFF| Return the earbuds to the charging case. Alternatively, when music is paused, you can press and hold either MFB button for 4 seconds. If music is playing, this function will not work.
Play Music| Press either MFB button.
Pause Music| Press either MFB button.
Next song| Press the right MFB button twice.
Previous song| Press the left MFB button twice.
Activate/Stop Voice Assistant| Press either MFB button three times.
Volume up| Press and hold the right MFB button for 2 seconds.
Volume down| Press and hold the left MFB button for 2 seconds.
Answer a call| Press either MFB button.
End a call| Press either MFB button.
Reject an incoming call| Press and hold either MFB button.

NOTE: The function compatibility may vary among different smartphones or devices. Not all functions are available on all devices.

CHARGING

CHARGING THE CASE

Use the included charging cable to fully charge the case before first use. It will take approximately 1.5 hours to fully charge.
The LED will flash during charging, and remain solid when charging is complete.

• Red LED ON indicates power level is lower than 25%.
• Yellow LED ON indicates power level is between 25%~50%.
• Green LED ON indicates power level is between 50%~75%.
• Blue LED ON indicates power level is between 75%~100%.

CHARGING THE EARBUDS

1. The earbuds will beep when the battery is low.
2. Place both earbuds into the charging case and close the lid. The LED indicator will be solid blue/green/yellow/red (depending on the charge case’s power level) when the earpbuds are charging and will turn OFF when fully charged.
   NOTE: Please make sure the charging case has enough power to charge the earbuds. Prior to first use, remove the plastic battery isolator tabs located on the earbud charging points. When the earbuds are paired to an Android™ or iOS device, the remaining earbud battery power will show on the device display.

PAIRING

1. Open the lid of the charging case. The earbuds will automatically turn ON. The LED will flash white and blue and the earbuds will beep to indicate that they have entered pairing mode.
2. Select “HRB 5035” on the Bluetooth device list to pair the earbuds automatically.
3. The earbuds will beep when Bluetooth is successfully paired.
4. After initial pairing, the earbuds will automatically turn ON and connect to your device when removed from the charging case, provided both earbuds and your Bluetooth are ON and within range.
5. The earbuds will automatically turn OFF after 5 minutes if no connection is established.

FIT
We recommend that you try each ear tip (small, medium and large), then perform a sound check and choose the combination that provides the best sound experience.

RESET

When the “L” and “R” earbuds cannot connect to each other, you will need to reset the earbuds and clear the paired memory:

1. Remove HRB “5035” from your list of Bluetooth devices.
2. Turn off Bluetooth in your device settings.
3. Remove the earbuds from the charging case and turn them OFF. Press and hold both MFB buttons for 8 seconds. The LED indicator will be white, then blue and you will hear a beep when the earbuds have been reset.
4. Return the earbuds to the charging case, close and then reopen the lid. The earbuds will automatically turn ON and pair with each other. You will hear a beep and the LED on the one earbud will flash blue and white, the LED on the second earbud will flash blue.
5. Turn on Bluetooth® in your device settings, Select “HRB 5035” to pair.

OPERATION

• While playing music, press either MFB button to pause, press again to resume
• Quickly press the right MFB twice for the next song, quickly press the left MFB twice for the previous song
• The music will pause and the earbuds will ring when there is an incoming call. Press either MFB button once to answer the call, press and hold to reject the call

WARNING!

• Supervise children when using equipment. This product is not a toy
• Listening to earbuds at high volume levels, particularly over extended periods of time may damage hearing
• If you have a pacemaker or other electrical medical device, you should consult your physician before using this product
• The operation of switching on your Hi-Fi system or plugging in the earbuds may cause clicks which at high volume settings, may affect your hearing. Therefore, always set the volume control to minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earbuds
• DO NOT use earbuds while driving or cycling
• The small parts included with this product can be a choking hazard. This product is not intended for use by small children and should be kept away from children under 3 years of age
• If not used for long periods, it is recommended to charge the earbuds and case at least every 3 months
• Please dispose of rechargeable batteries properly. DO NOT dispose of batteries in fire to prevent an explosion

TROUBLESHOOTING

No sound

• Please check the volume on your audio device to make sure it is outputting sound

Connection Problems

• Please return the earbuds to the case and then remove them again if there are any connection issues
• Refer to the cleared paired memory and reset section

The earbuds are not fitting comfortably

• Please switch out the earbud tips to a different size to find the appropriate fit

Improve the Sound

• Sound can sometimes be improved by moving to a larger eartip size. The eartips still need to fit comfortably in your ear

CLEANING

Your earbuds may require periodic cleaning. Use a dry, soft, lint-free cloth to clean your earbuds. To clean the microphone and speaker mesh, use a dry cotton swab.

IMPORTANT SAFETY INFORMATION

CAUTIONS

• Keep in a safe place free from dust, liquid and extreme temperatures
• DO NOT attempt to disassemble the product
• DO NOT use chemicals to clean the product

SPECIFICATIONS

• Bluetooth® version: v5.1
• *Bluetooth® profiles:** HSP; HFP; A2DP; AVRCP; APTX

EARBUDS

• Wireless range: 10m (32ft.)
• Playback time: approx. 11 hours**
• Standby time: approx. 60 hours
• Rated input: DC 5V/70mA
• Driver diameter: 6mm
• Sensitivity: 90db±3db
• Frequency response: 20Hz~20kHz
• Impedance: 16 Ohms±15%
• Battery: Polymer Lithium
• Battery capacity: 70mAh
• Earbuds charging time: approx. 1.5 Hours
• IP rating: IPX4

CHARGING CASE

• Rated input: DC 5V, 500mA
• Output: DC 5V, 300mA
• Battery Capacity: 400mAh
• Case charging time: Approx. 1.5 hours
• Fully powered case: Provides up to 1.5 charges

1. A2DP=Advanced Audio distribution Profile, AVRCP=Audio Video Remote Control Profile, HSP=Handset Profile, HFP=Handfree Profile.
2. Approximate playback time, battery life depends on individual use and may be more or less than specified.
3. Standby, Bluetooth® connected, power ON, no music playing.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other trademarks and trade names are those of their respective owners.

FCC

INDUSTRY CANADA NOTICE RSS247
This device complies with Industry Canada license-exempt RSS standards(s). Operation is Subject to the following two conditions:

• This device may not cause interference, and this device must accept any interference,including interference that may cause undesired operation of the device
• This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada

ISED REGULATORY COMPLIANCE
This device contains licence-exempt transmitters that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

• This device may not cause interference
• This device must accept any interference, including interference that may cause undesired operation of the device

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
IC:255A-8093128
CAN ICES-003(B)/NMB-003(B)

THE SOURCE – WARRANTY

The Source warrants that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of purchase. Within this period, simply take the product and your proof
of purchase to any The Source store or participating dealer and the product will be replaced (where available) without charge. Any product which has been subject to misuse or accidental damage is excluded
from this warranty.
This warranty is only applicable to a product purchased through The Source company-owned stores or participat-ing dealers in Canada where the warranty is included with the product. While this warranty does not confer any legal rights other than those set out above, you may have additional statutory rights which will vary under the laws of the various countries, states, provinces and other governmental entities in which
The Source operates. This warranty is subject to all statutory rights you may have in Canada.

Imported by:
The Source, Barrie, Ontario, Canada, L4M 4W5 Manufactured in China
www.thesource.ca
© 2021 The Source. All rights reserved.

References

• La Source | Computers, Tablette et jeu, TV et audio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>