HEADRUSH HRB 5029 True Wireless Earbuds Instruction Manual

: June 6, 2024
: HeadRush

HEADRUSH HRB 5029 True Wireless Earbuds Instruction Manual

INTRODUCTION

Thank you for purchasing the HRB 5029 true wireless earbuds. In order to maximize your listening experience please read the following instructions.

Overview

Product Overview Product
Overview

LED indicator
MFB (Multi—function button)
Microphone
3 charging case LED indicators
Check case battery button
Micro USB port

WHAT’S INCLUDED

HRB 5029 Earbuds
Charging case
Micro USB charging cable
Instruction manual

OPERATING INSTRUCTIONS

TO	DO THIS
Power ON	Remove the earbuds from the charging case OR press and hold both MFB

buttons for approximately 3 seconds.
Power OFF| Place earbuds back in charging case OR press and hold both MFB buttons for approximately 5 seconds.
Play/Pause| Press either MFB button once.
Next song| Press and hold the right MFB button.
Previous song| Press and hold the left MFB button.
Answer/end a call| Press either MFB button once.
Reject an
incoming call| Press and hold either MFB button.

NOTE: The function compatibility may vary among different smartphones or devices. Not all functions are available on all devices. Prior to first use, remove the clear plastic battery isolator tab located between the earbuds and charging case.

CHARGING THE CASE

Use the included charging cable to fully charge the case before first use. It will take approximately 2 hours to fully charge.

There are 3 LED indicators on the case
When the case is charging, the 1st, 2nd and 3rd LED will flash, indicating the battery case’s power level-1 is low, 2 is medium and 3 is a full charge
All 3 white LEDs will stay on when the case is fully charged
To check the remaining battery power on the case when it’s not charging, press the button on the case:
1. LED ON indicates a low battery
2. LEDs ON indicates a medium-charged battery
3. LEDs ON indicates a fully-charged battery

CHARGING THE EARBUDS

The earbuds will automatically power OFF and begin charging when they are placed in the charging case. The red LED will be ON to indicate the earbuds are charging and turn white when charging is complete. The white LED will last for 20 seconds, then turn OFF. It will take 1.5 hours to fully charge the earbuds. The earbuds can be charged 6 times using a fully charged case.

NOTE: During use, the red LED on the earbuds will flash slowly when their battery level is low. Please charge the earbuds.

PAIRING

The earbuds will automatically enter Bluetooth’ pairing mode when used for the first time.

Remove both earbuds from the charging case. Please refer to the L or R print on the inside stem on each earbud, and place in the correct ear. The earbuds will beep when powering ON and when pairing. The red and white LED will flash. Turn Bluetooth® ON in your device settings and select “HRB 5029”
Follow the instructions and enter “0000” as PIN, if required
When the earbuds are successfully paired, the white LED will flash every 10 seconds

After initial pairing, the earbuds will automatically connect to your device when removed from the charging case, provided either the left or right earbud and your Bluetooth® are ON and within range. If you would like to use the only one earbud, simply place the paired earbud back into the case. The earbud remaining in your ear will continue to play.
If you use a single earbud for use the first time, take the L or R earbud out of the charging case.
Select ‘HRB 5029’ from your Bluetooth° list.
To switch from using the single earbud back to TWS mode, put the L or R earbud back into the charging case, then take both earbuds out. The L and R earbuds will automatically pair to each other

NOTE: The L and R earbuds automatically pair to each other. Should the connection fail, please follow the steps below:

Press both MFB buttons three times to enter the default setting, and the white and red LEDs will flash once
Press and hold both MFB buttons for three seconds to enter TWS pairing mode, and the red and white LEDs will flash quickly

CLEAR PAIRED MEMORY AND RESET

When the L and R earbuds can’t connect to each other, you will need to reset the earbuds and clear paired memory.
To clear the memory:

Remove HRB 5029 from your device listing and turn Bluetooth® OFF on your device
Press both MFB buttons three times when both earbuds are powered on and you will hear 4 long beeps
If you don’t have the charging case with you, press both MFB buttons for 3 seconds till you hear 3 beeps. This indicates the earbuds have powered on
Alternatively, put both earbuds back in the charging case and take them out. You will hear 3 beep sounds and the earbuds will power on automatically
Turn Bluetooth® back on in your device settings and select ‘HRB 5029’

OPERATION

While playing music press either MFB button to pause, press again to resume
Press and hold the right MFB button to skip to the next track
Press and hold the left MFB button to go back to the previous track
The music will pause and the earbuds will ring when there is an incoming call. Press either MFB button once to answer the call, press and hold to reject the call
While talking, press either MFB to end the call To disconnect from your device while still wearing both earbuds and are not listening to music or having a phone conversation:
Enter the Bluetooth® settings in your paired device, select “HRB 5029” and click disconnect
The earbuds can also be turned off by pressing and holding either MFB button for approximately 5 seconds. The earbuds can be turned on again by pressing and holding both MFB buttons for approximately 3 seconds

WARNING!

Supervise children when using equipment, this product is not a toy
The earbuds are not waterproof or water resistant. DO NOT use outside in rain or during intensive exercise
Listening to earbuds at high volume levels, particularly over extended periods of time may damage your hearing
If you have a pacemaker or other electrical medical devices, you should consult your physician before using this product
The operation of switching on your Hi-Fi system or plugging in the earbuds may cause clicks which at high volume setting may affect your hearing. Therefore, always set the volume control to minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earbuds
DO NOT use earbuds while driving or cycling
The small parts included with this product can be a choking hazard. This product is not intended for use by small children and should be kept away from children under 3 years of age
If not used for long periods, it is recommended to charge the earbuds and case at least every 3 months
Please dispose of rechargeable batteries properly. DO NOT dispose of batteries in fire to prevent an explosion

TROUBLESHOOTING

Problems Pairing
- Please press both MFB buttons 3 times to reset both earbuds when there is a problem with TWS or Bluetooth® connection. Please refer to the clear paired memory and reset section
No sound
- Please check the volume on your audio device to make sure it is outputting sound
The earbuds are not fitting comfortably
- Check to ensure you have the left and right earbuds in the correct ears

CLEANING

Your earbuds may require periodic cleaning. Use a dry, soft, lint-free cloth to clean your earbuds. To clean the microphone and speaker mesh, use a dry cotton swab.

IMPORTANT SAFETY INFORMATION

CAUTIONS

Keep in a safe place free from dust, liquid and extreme temperatures
Do not attempt to disassemble the product
Do not use chemicals to clean the product

SPECIFICATIONS

EARBUDS

Bluetooth version: V5.0
Bluetooth profiles: A2DP/AVRCP/HSP/HFP*
Wireless range: 10m (32ft.)
Playback time: Approx. 5 hours**
Standby time: Approx. 1 day***
Rated input Earbuds: DC 5V, 40mA
Driver diameter: 10mm
Sensitivity: 97dB ± 3dB
Frequency response: 20Hz-20kHz
Impedance: 32Ω ± 10%
Battery: Polymer Lithium
Battery Capacity:
- Earbuds: 40mAh
- Charging case: 550mAh

CHARGING CASE

Input: DC 5V, 550mA
Output: DC 5V, 300mA
A2DP- Advanced Audio Distribution Profile, AVRCP-Audio Video Remote Control Profile, fiSP-Handset Profile, HFP-Handsfree Profile.
- Approximate playback time, battery life depends on individual use and may be more or loss than specified.
- Bluetooth° connected, power ON, no music palying.

BLUETOOTH

Bluetooth Icon

The Bluetooth° word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The Source (Bell) Electronics Inc. is under license. Other trademarks and trade names are those of their respective owners.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

INDUSTRY CANADA NOTICE RSS247

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada.

RF EXPOSURE COMPLIANCE

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISED REGULATORY COMPLIANCE

This device contains licence-exempt transmitters that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.