Wyrestorm SW-540-TX-W 4-Input 4K HDBaseT Presentation Switcher with Matrix Outputs USB 2.0 Multiview and Wireless Casting User Guide

Wyrestorm SW-540-TX-W 4-Input 4K HDBaseT Presentation Switcher with Matrix Outputs USB 2.0 Multiview and Wireless Casting User Guide

Installation Requirements

IMPORTANT

• Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
• Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.

In the Box

• 1x SW-540-TX-W Transmitter
• 1x 12V 2A Power Supply (US/UK/EU/AU)
• 2x 4-pin Terminal Blocks
• 2x Mounting Brackets with Screws
• 1x Quickstart Guide (This Document)

Basic Wiring Diagram

Wiring and Connections

Wyre Storm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable transmitters, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken  to minimize or remove these factors completely during installation for bestresults.
• Wyre Storm recommends using pre-terminated VGA, HDMI, DP and USB cables due to the complexity of these connector types. Using predetermination cables will ensure that these connections are accurate and will not interfere with the performance of the product

Audio Connections

The audio connections use a 3.5mm (1/8in) TRS Stereo Jack.

Communication Connections

RS-232 Wiring
The SW-540-TX-W uses a 3-pin RS-232 with no hardware flow control. Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made.

PC Connection
Connection to a PC uses the RS-232 Control connection and requires the use of a USB to 3-pin Port Adapter cable (CAB-USB-3PIN) in order for a port to be provided on the PC. Note that this adaptor can be used on both v1 and v2 versions.

• This product contains a USB-C connection that can be used as an audio/ video input. When using this connection verify that the USB-C cable used supports audio/video functionality as not all USB-C cables support this requirement.
  

RS-232 Passthrough

RS-232 Control

Setup and Configuration

The SW-540-TX-W is configured using RS-232 or IP commands for Output Resolution, and EDID. Follow these steps to properly configure the transmitter based on the system requirement.
Note: The steps and information provided in this QSG are for basic operation of the transmitter out of the box. Refer to the SW-540-TX-W API for full configuration settings.

1. Assign a Static IP Address to ensure proper communication on an IP Network.
2. Set EDIDs to be used at each input of the device. See Configuring Input EDIDs

Communication Settings

The SW-540-TX-W contains a web UI that can be accessed by connecting to a network and entering the IP address. We recommend that the IP address is changed from default before accessing the web UI for the first time.

RS-232 and IP Settings

Guide Screen

The switcher uses a Guide Screen to convey the basic connection instructions for user access. The Guide Screen can be personalized to allow custom connection instructions on the switcher’s Web UI page

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device.
• Verify that all HDMI and HDBaseT connections are not loose and are functioning properly.
• Verify that the HDBaseT cable is properly terminated following EIA568B standard.
• Verify that the output resolution of the source and display is supported by this transmitter.
• Configure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR, RS-232, and Ethernet cables are properly terminated following the Wiring and Connections section.

Relays Not Functioning

• Verify polarity of the relay connections.

Troubleshooting Tips

• Wyre Storm recommends using a cable tester or connecting the cable to other devices to verify functionality

FCC Statements

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The distance between user and products should be no less than 20cm.

Declaration of Conformity

We declare that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Manufacturer: Shen Zhen Proitav Technology Co.,Ltd
Address: 301-401, Building 16, Hejing Industrial Park, No.87, Hexiu west Road,Heping Community, Fuhai street, Baoan District, Shenzhen, China.

Accessory Manufacturer: ShenZhen Tianweixun Wireless Technology Co., Ltd
Adapter: Antenna
Address of Manufacturer: 9/F, Building 1, Guole Science and Technology Park, No. 1 Lirong Road, Dalang Street, Longhua New District, Shenzhen.

Accessory Manufacturer: Dongguan NB Power Electronic Limited
Adapter: Power supply
Address of Manufacturer: No.365, South Dongkeng Road, Dongkeng Town, Dongguan City, 523443, P. R. China
The adapter shall be installed near the equipment and shall be easily accessible.

Accessory Manufacturer: Shenzhen Ohonda Technoligy Co., LTD
Adapter: Terminal block
Address of Manufacturer: Room 609, Block D, Hongtaifu Building, Zone No.34, Baoan District, Shenzhen

Operating temperature: 0°C to 45°C
Wi-Fi Operation Frequency: 2412MHz~2472MHz
Maximum Power: 16.74dBm(E.I.R.P.)

Specifications

Audio and Video|
---|---
Inputs| 1 x VGA In: 15-pin VGA

1 x Audio In 3.5mm (1/8m) 7RS Stereo

2x HDMI In: 19-pin type A

n: oSEIC

:, reless Video from /airplay or kliraeast Source

Outputs| 1 x Mirrored MD87 Out: &pm R/-45 Female lx KOMI Out I9-pin type A

lx HOW Out: 19-pin type A (Output 2) lx Audio Out: 3.6mm (1/Bin) TAS Stereo

Video Encoding| HDBaseT Class 8
Encoding Data Rate| 9.2Gbps
Mirrored Output Latency| I Ops (micro seconds)
Audio Formats| 2ch Analog I PCM
Video Resolutions (Max)| Video Resoludono Wired Input/Output| HDBT Output Ca16/6a
‘ VGA A CAMS; 1920x1080p @60Hz Shit                               VGA: 8m/25. ‘|
HDMI 8 USB-C: 384052160p p3Ohtz 8ba 4:4:4                      NOMVUSB-C:|
Supported Standards|  1 riGB
Maximum Pixel Clock| • .JuNIFIz
Communication and Control|
HDMI| DMI1HD
HOBaseT| HON! HD..
US8| 3 x 1.r.,:R : 2:x LI::
RS-232| 104E2., Ix RS-232 .
Ethernet|
Wireless|
Power|
Power Supply| 12VOC 2A
Max Power Consumption| 24W
Environmental|
Operating Temperature| 0 to • 45.0(32 to • 113’1).10% to 90%, non-condensing
Storage Temperature| -20 to •70°C (-4 to* 168 •F). 10% to 90% non-condensing
Max BTU| 82 BTU/hr
Dimensions and Weight|
Rack Units/wall Box| c1U
Height| 25mm/0.98M (Antennas Excluded)1180mm/7.08in (Antennas Included)
width| 215mm/8.46in (Antennas Excluded)1216mnVEL4Ein (Antennas hicluded)
Depth| 140.2mm/851in (Antennas Excluded)1180mm/7.08in (Antennas bxluded)
weight| 0.97kg/2.13115s
Regulatory|
Safety and Emission| CE | FCC | RoHS | RCM | EAC

• Note: Wyr eStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.

Warranty Information

WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.

Support

Copyright © 2021 WyreStorm Technologies
wyrestorm.com
SW-540-TX-W Quickstart Guide | 210607
UK: +44 (0) 1793 230 343
ROW: 844.280.WYRE (9973)
support@wyrestorm.com

References

• WyreStorm - Professional Audio Visual Solution Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>