WyreStorm RX3-100 In Wall Transmitter HD BaseT 3.0 Receiver User Guide
- June 1, 2024
- WyreStorm
Table of Contents
Quickstart Guide
4K60Hz HDBaseT 3.0 Receiver with USB
Device Inputs, Audio De-embed & PoH
RX3-100
RX3-100 In Wall Transmitter HD BaseT 3.0 Receiver
WyreStorm recommends reading through this document in its entirety to become
familiar with the product’s features prior to starting the installation
process.
IMPORTANT!
Installation Requirements
- Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
- While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
In the Box
1x RX3-100 HDBaseT 3.0 Receiver
1x 3-pin Terminal Block
4x Wall Mounting Brackets
4x Mounting Screws
1x 20V 3A PSU
1x Quickstart Guide
Does not support USBC charging on TX
Basic Wiring Diagram
RX3-100 (Front/Rear)
A Power LED| Solid: The unit is powered On
Off: The unit is powered Off
---|---
B Link LED| On: Indicates link with receiving device
Off: No link with receiver/powered off
C Source LED| On: Indicates the video output
Off: No video output
D SET Dip Switches| Adjust RS-232 function
E Audio Line In| 3.5mm jack: 2ch analog audio input
F USB Device| USB Type A female
Connection of USB device peripherals
A Power Input| 20V 6A Screw Down Jack
---|---
B RS-232| 3-pin Phoenix: Serial input for API control and 20v input
C HDBT Input| 8-pin RJ-45 female Connect the transmitter’s HDBT OUT to
receiver’s HDBT IN.
D HDMI Output| 19-pin type A HDMI female Supports HDMI and DVI/D with adapter
E Audio Output| 3.5mm jack: 2ch analog audio input
DIP Switch Control
The four-pin DIP switch can be used to adjust RS-232 function.
Pin 2 is set to the “Up” position, RS-232 Control mode. RS-232 port is used to
control the receiver and remote transmitter. In this mode, users can upgrade
the receivers MCU firmware.
Pin 2 is set to the “Down” position, RS-232 HDBaseT Firmware Upgrade. Users
can upgrade firmware in this mode.
Pin 1, Pin 3 and Pin 4 are reserved. The positions of these two pins will not
affect IR and RS-232 function.
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends using pre-terminated HDMI and USB cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
- This product contains a USB-C connection that can be used as an audio/ video input. When using this connection verify that the USB-C cable used supports audio/video functionality as not all USB-C cables support this requirement.
RS-232 Wiring
The RX3-100 uses a 3-pin RS-232 with no hardware flow control. Most control
systems and computers are DTE where pin 2 is RX, this can vary from device to
device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
WyreStorm Connector
| | 3rd Party Device
---|---|---
Pin 1| TX (Transmit)| —> To —>| RX (Receive)
Pin 2| RX (Receive)| —> To —>| TX (Transmit)
Pin 3| G (Ground)| —> To —>| G (Ground)
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
- Verify that power is being supplied to the transmitter and receiving device.
- Verify that all HDMI, USB and HDBaseT connections are not loose and are functioning properly.
- Verify that the HDBaseT cable is properly terminated following EIA568B standard.
- Verify that the output resolution of the source and display is supported by this extender.
- If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated
No or Intermittent 3rd party Device Control
- Verify that the RS-232 cables are properly terminated following the Wiring and Connections section.
Troubleshooting Tips:
- WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
Note: WyreStorm reserves the right to change product specification,
appearance or dimensions of this product at any time without prior notice.
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects
in material and workmanship under normal use for a period of five (5) years
from the date of purchase. Refer to the Product Warranty page on wyrestorm.com
for more details on our limited product warranty.
Copyright © 2023 WyreStorm ProAV Corporation
wyrestorm.com
RX3-100 Quickstart Guide | 231101
INT: +44 (0) 1793 230 343
US: 844.280.WYRE (9973)
support@wyrestorm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>