FLUVAL SHAKER 168L 44 US Gal / 168 L Aquarium Kit Instruction Manual
- June 6, 2024
- FLUVAL
Table of Contents
Instruction manual: LED Strip Light and Aquarium
READ THOROUGHLY PRIOR TO INSTALLATION AND OPERATION
IMPORTANT: FULLY ASSEMBLE THE CABINET BEFORE REMOVING THE TANK FROM ITS BOX AND NEVER PLACE THE AQUARIUM ON ANY SURFACE OTHER THAN THE CABINET TO PREVENT DAMAGE TO THE AQUARIUM BASE.
FLUVAL SHAKER LED: PARTS
The Shaker Aquarium kit contains two separate packages. Carefully remove all
components from the packaging and make sure that nothing is missing or
damaged.
1
package including:
1x glass tank (A), 2x sliding top covers (B),
1x LED Strip light (C) + LED driver with instruction manual,
1x plastic bag with 4x cable guides (D) and 1x over rim cable guide (E) with
bi-adhesive pad,
1x Fluval filter, with its instruction manual,
1x heater with its instruction manual
1 package (supplied separately) including: the disassembled cabinet and the
top wooden frame to apply to the glass tank, with instruction manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To guard against injury, basic safety precautions should be observed when handling the LED Strip Light, including the following:
-
For the complete enjoyment, use and understanding of this product, READ AND FOLLOW ALL SAFETY INSTRUCTIONS and all important notices on the appliance before using. Failure to do so may result in loss of fish life and/or personal injury or damage to the unit.
-
DANGER To avoid possible electrical shock, special care should be taken due to the close proximity of the LED Strip Light to water. For each of the following situations, do not attempt repairs yourself; return the appliance to an authorized service facility for service or discard the appliance. (See Customer Service information at the end of this manual).
If the unit falls into the water, DON’T reach for it! First unplug it and then retrieve it. If the electrical components of the appliance get wet, unplug the appliance immediately.
Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.
Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning, dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the cord is damaged, the appliance must be discarded. Never cut the cord.
To avoid the possibility of the appliance plug or wall socket getting wet, position the unit to one side of a wall mounted socket to prevent water from dripping onto the socket or plug. A “drip loop” (see illustration) should be arranged to the socket. The “drip loop” is that part of the cord below the level of the socket (or the connector if an extension cord is used), to prevent water travelling along the cord and coming into contact with the wall socket. If the plug or socket does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug and examine for presence of water in the wall socket. -
WARNING – Close supervision is necessary when any appliance is used by or near children. This appliance can be used by children ages 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. This product is not a toy.
-
To avoid injury, do not come into contact with moving parts or hot parts such as heaters, LED devices, etc.
-
CAUTION Always unplug or disconnect all appliances in the aquarium from electricity supply before placing hands in water, before putting on or taking off parts and when this LED Strip Light is being installed, maintained or handled. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.
Always unplug an appliance from an outlet when not in use.
WARNING: BE SURE YOU UNPLUG THE LED DRIVER FROM THE POWER OUTLET; JUST SWITCHING OFF THE APPLIANCE WITH THE APP IS NOT ENOUGH BECAUSE IT DOES NOT STOP THE POWER SUPPLY.
Do not use this appliance for any purpose other than its intended use (i.e. don’t use in swimming pools, garden ponds, bathtubs, etc.). The use of attachments not recommended or sold by the appliance manufacturer may result in a dangerous situation. Do not try to repair any product component: in case of damage, replace the damaged component with genuine spare parts. -
IMPORTANT: This LED Strip Light is an AQUARIUM LUMINAIRE suitable FOR INDOOR USE ONLY designed to be assembled onto Fluval Shaker Aquariums only. For fresh and salt water ornamental aquariums with max 35°C water temperature. Do not install or store the appliance anywhere where temperatures may drop below freezing.
-
IMPORTANT: Make sure that the LED Strip Light is securely and correctly installed before operating. This LED Strip Light must never operate in water.
Fill the aquarium up to the level indicated on the label situated on the inside of the aquarium (see the image on the right). IMPORTANT: Do not overfill.
Overfilling the aquarium can cause water to pass under the top frame which then runs down the outside of the aquarium.
WARNING: Do not plug in the LED Strip Light if there is water on parts not intended to be wet.
WARNING: Do not place any object(s) on the LED Strip Light (C) or on the cover. Ensure sufficient airflow around the LED Strip Light. The safety of this appliance is only ensured provided that it has been properly installed. -
Read and observe all the important notices on the appliance.
-
If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
-
SAVE THESE INSTRUCTIONS.
FOR USA ONLY
FCC Statement This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Change or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
FULL SETUP GUIDE
AQUARIUM CABINET INSTALLATION AND PREPARATION
Before handling the aquarium tank and cabinet, ensure you have sufficient people to move them without any risk.
ASSEMBLE THE AQUARIUM CABINET BEFORE REMOVING THE AQUARIUM FROM ITS PACKAGING.
You MUST place the Fluval aquarium on the appropriate Fluval cabinet which was
designed with the correct dimensions and structure to bear the weight of the
aquarium full of water. The use of different cabinets, pieces of furniture, TV
stands, etc., WILL invalidate your warranty and will compromise the product
safety.
Please refer to the instruction manual of the aquarium cabinet. Do not attempt
to set up the cabinet without reading and following the instruction manual. If
it is missing or unusable, contact the store or Hagen Customer Service.
Placing the aquarium with its cabinet in the final location
Location of the aquarium is very important. Place the aquarium away from
direct sunlight. This will reduce the risk of excessive algae build-up and
avoid overheating the aquarium by the sunrays. Keep your Fluval Aquarium away
from other sources of heat (air ducts, radiators, etc.) for proper temperature
maintenance. Drafts should also be avoided. Do not locate your Fluval Aquarium
where water spills will cause damage.
WARNING: Ensure that the selected position has an even and level surface which is able to support the total weight of the aquarium full of water and the cabinet. Place your new Fluval Aquarium and cabinet close to an electrical outlet. After placing the cabinet, assure that it is perfectly level by using an adequate leveling tool.
IMPORTANT: Fluval cabinets are designed to support the total weight of the aquarium. The table below shows the approx. height of filling of the tank and approx. weight of the aquarium full of water (rocks, decorations or gravel have not been considered).
FLUVAL SHAKER AQUARIUMS
Model| External Tank Dimensions| Height of Filling
(Up to the max water level line)| Weight of aquarium filled only with water
Fluval Shaker 168 L| 70 x 40 x 60 cm (27.6 x 15.7 x 23.61| 54.5 cm (21.5″)
(Water capacity = 140 L (37 US gal))| 168 kg (370Ib)
Fluval Shaker 252 L| 105 x 40 x 60 cm (41.3 x 15.7 x 23.6″)| 54.5 cm (21.5″)
(Water capacity = 210 L (56 US gal))| 261 kg (5751b)
THE AQUARIUM INSTALLATION
Before handling the aquarium tank and cabinet, ensure you have sufficient people to move them without any risk.
Take the aquarium tank out from its packaging.
The aquarium glass tank comes with runners glued to it to support the LED
Strip Light and covers. Do not try to remove the runners.
The tank is made of glass, always handle it with the utmost care. Make sure to
lift it only by the base.
Place the aquarium tank onto the cabinet.
IMPORTANT: Thoroughly clean the top side of the cabinet base and the lower
side of the aquarium base.
Place the empty aquarium tank onto the cabinet, making sure that the
connections lie in the appropriate opening of the cabinet and NEVER insert any
lining (e.g. Polystyrene) mats, or bases between cabinet and aquarium.
https://fluvalaquatics.com/care2020/
For further information on aquarium care, scan here.
WARNING: Risk of breaking the glass tank base. The glass tank features
protruding fittings at the bottom, which can never be used as support points.
Never try to lay the tank on any support except its cabinet, which is fitted
with a special cavity to accommodate the fittings. When placing the tank onto
its cabinet, remove the tank from the box and rest it on the cabinet paying
the utmost attention not to damage the bottom fittings.
Never attempt to move or transport the cabinet with the glass tank or
any other load on top of it.
Although the glass tank was manufactured with the maximum care and the
most advanced techniques, we still recommend making a simple inspection prior
to the installation to verify that unexpected events during handling and
transportation have not damaged the tank or impaired its water-tightness.
- Make a visual inspection of the glass tank to check for damage or cracks. Do not continue the installation if the tank is damaged.
- If no damages and cracks are detected, proceed with the normal aquarium set up.
- After the full installation of the aquarium kit with filter, heater, LED strip light, decorations, etc., has been completed, fill the tank with water 5 cm at a time, while making sure there are no leaks.
Never attempt to move or transport the tank if it is not completely
empty of water or any other material.
Always take care not to damage the seals at the edges of the glass
panels while maintaining your aquarium, ie: with planters or algae scrapers.
**** Never use toxic or aggressive substances to clean your aquarium, such as
household detergents.
QUICK CONNECTION SYSTEM INSTALLATION
This section only applies to Fluval Aquariums with Fluval External filter
and “QuickConnect” System.
Installing water intake/output with “QuickConnect” system (Intake/output
fittings are included in the filter packaging)
These Fluval Aquarium models feature the “QuickConnect” system, which allows
the direct connection of the tank to the external filter through the bottom
glass by means of special fittings. Normally, the same type of connection is
achieved through specially-made devices, which are complex and require the
intervention of expert technicians. On the contrary, in just a few minutes the
“QuickConnect” system can be easily and safely installed, giving your aquarium
a professional and tidy filtration solution.
Before proceeding, identify and count all parts required by referring to the
exploded view in the side illustration. If any part is missing, do not proceed
with the installation and contact your local supplier.
Before proceeding, check stems (A) for the presence of all 3 rubber rings (C).
Do not proceed with the installation if one of the rubber rings (C) is missing
and contact your local supplier.
Locate the 2 openings in the tank bottom glass and assure that the
corresponding openings
in the cabinet are aligned with
them. The 2 openings in the tank bottom glass are complete with factory-
installed special plastic fittings, which must never be removed, turned or
loosened and with 2 sealing plugs (P) and (Q). The output group should be
installed in the opening (O), whereas the intake group should be installed in
the opening (I).
Do not force, loosen or turn
the factory-installed special fittings on tank openings (I) and (O).
Once the output/intake groups are installed, do not shift the tank with
respect to the cabinet as this may damage the output/intake devices and the
glass tank.
Output system installation
- Manually unscrew plug (P) and remove plug (Q) from opening (O) (Pict. 1). IMPORTANT: keep plugs (P) and (Q) for any future use.
- Slip connector stem (A) fully through opening (O) until it stops (Pict. 2).
- Open the cabinet. Screw and tighten the ring nut (R) onto the bottom end of stem (A) (Pict. 3).
- Insert the output nozzle (N) into one end of output stem (B).
- Insert output stem (B) onto connector stem (A) (Pict. 4).
- Adjust the height of output nozzles according to your requirement by sliding outlet stem (B) along connector stem (A).
- The output nozzles (N) can be easily rotated to divert the water flow where desired.
Direct water jets so as not to let water overflow from the tank. Avoid directing the water jets towards the LED Strip Light.
Intake system installation
- Manually unscrew plug (P) and remove plug (Q) from opening (I) (Pict. 1). IMPORTANT: keep plugs (P) and (Q) for any future use.
- Slip the second connector stem (A) fully through opening (I) until it stops (Pict. 2).
- Open the cabinet. Screw and tighten the nut ring (R) onto the bottom end of the second stem (A) (Pict. 3).
- Insert the intake strainer (S) onto connector stem (A) (Pict. 5). The assembly end result is shown on Pict. 6 and Pict. 7.
The height of the intake strainer is high enough to suit most standard
aquarium decorations. When decorating the aquarium, ensure it remains at least
5 cm from the gravel bottom at all times to prevent it from sucking gravel or
sand and ensure that no decorations block the passage of water. Ornaments and
rocks should be positioned while the aquarium is still dry.
CAUTION!: Never force Connector Stems (A) sideways, as this may damage
the output/intake systems and the glass tank. In the event a different
filtration system is used, which does not require the Intake/Output systems
supplied with this unit (e.g. an internal filter), restore the initial
conditions by removing the 2 connector stems (A) and closing openings (O) and
(I) with plugs (P) and (Q). Plug (Q) ensures a watertight seal and has to be
inserted into its seat by pressing it. Plug (P) is designed to protect plug
(Q) and ensure that plug (Q) remains in its seat properly. Screw plug (P) by
hand only until it will no longer go without forcing it.
DO NOT USE ANY TOOLS, AS DOING SO MAY DAMAGE THE UNIT.
CABLE GUIDES AND OVER RIM CABLE GUIDE ASSEMBLY INSTRUCTIONS
The power cables of the heater and the LED strip light will be routed out through the back of the aquarium using an over rim cable guide which can be placed on the right or on the left.
- Determine if the cables should come out from the left or from the right. (TIP: Heaters are most effective when positioned near the filter output stem).
- Place the cable guides where most appropriate, by sliding them in the lower runner of both rails (Pict. 8).
- Clean and dry the area where the over rim cable guide will be positioned.
- Stick the double-sided tape in the provided location of the over rim cable guide (Pict. 9).
- Peel off the cover paper from the tape.
- Apply the over rim cable guide inside the tank after aligning it with the top edge of the glass (as shown in Pict. 8) by gently pressing it to the glass. To ensure optimal adhesion wait 24 hours before filling the tank with water.
ASSEMBLE THE TOP WOODEN FRAME (SEE SEPARATE INSTRUCTION MANUAL WHICH IS FOUND IN THE CABINET BOX).
FLUVAL FILTER & HEATER INSTALLATION, USE AND MAINTENANCE
Please refer to the instruction manual of the Fluval filter/heater. Do not attempt to set up the Fluval filter/heater without reading and following the instruction manual. If it is missing or unusable, contact the store or Hagen Customer Service.
LED STRIP LIGHT INSTALLATION INSTRUCTIONS
WARNING: Disconnect the plug of all electrical equipment used for the
aquarium, before placing your hands in aquarium water and/or performing any
maintenance of any kind.
Initial start-up
- Carefully place the LED Strip Light (C) on the runner of the top frame in the final position (Pict. 11).
- Pull the LED Strip cable out through the cross of the rim cable guide (as indicated above).
- Hook up the lighting unit to the LED driver with its connector (Pict.12).
WARNING: Do not plug in the LED Strip Light if there is water on parts not intended to be wet.
Switching the LED Strip Light On
Plug in the unit and use a smartphone or tablet with the FluvalSmart app
downloaded to connect to it. The FluvalSmart App can be downloaded from the
iOS or Android App stores, or scan the QR code to download. Use exclusively
the LED driver supplied with the LED Strip Light. In all cases, make sure that
the LED driver specifications comply to the specifications indicated in the
LED Strip Light identification codes table below.
http://www.fluvalaquatics.com/led-uk
FLUVAL SHAKER LED STRIP LIGHT SPECIFICATIONS
Aquarium Model| 168L SHAKER| 252L SHAKER
LED STRIP LIGHT UNIT| BT LED UNIT SHAKER| BT LED UNIT SHAKER
LED STRIP LIGHT MODEL NUMBER| A13246| A13247
LUMINAIRE WATTAGE| 16.5 W| 24 W
LUMENS| 13001m| 19501m
LUMINAIRE OPERATING VOLTAGE| 24Vdc| 24Vdc
LED DRIVER TYPE| S018BA[X] 2400063| S024AM[X] 2400100
LED DRIVER INPUT VOLTAGE| 100-240 Vac| 100-240 Vac
X = B For UK Plug X = V For EU Plug X = U For US Plug X = S For AUS Plug
Place the sliding covers on the tank.
Peel off the protective film from the two aquarium covers.
- Lay the narrow cover in the lower sliding surface of the runners (support rails).
- Lay the wider cover in the upper sliding surface of the runners (support rails).
Maintenance
For maximum LED performance, it is recommended that the fixture and the LED
lens be cleaned on a weekly basis. Unplug the LED driver prior to cleaning the
light fixture. Use both hands when manipulating this appliance. Wipe exposed
surfaces carefully with a damp cloth to remove any dust or mineral deposits
that may collect over time. Do not use detergents or harsh cleaners as it can
damage the light fixture.
Use
Fluval LED Lens Cleaning Kit (A3969) to clean the LED portion of the light
fixture. Make sure all surfaces are dry before re-connecting the LED driver to
the power source.
Troubleshooting
If the LED Strip Light does not turn on, please proceed as follows:
PROBLEM | CAUSE | SOLUTION |
---|---|---|
The light isn’t working. | Missing connection of the LED driver to the power | |
outlet. | Connect the LED driver to the power outlet. | |
Missing connection of the lighting unit to the LED driver. | Connect the |
lighting unit to the LED driver with its connector.
If the problem is not solved after following the above, please contact your
Hagen retailer.
LED STRIP LIGHT AND TANK MAINTENANCE
Cleaning the LED
Strip Light Disconnect the Strip Light from power supply before any
maintenance operation.
WARNING: Be sure you unplug the LED driver from the power outlet; just
switching off the lights with the APP is NOT enough because it does not stop
the power supply. Never place the LED Strip Light under water jets or submerge
in water.
No special maintenance is required for the Fluval LED Strip Light and covers,
other than periodic cleaning with a damp cloth (never use harsh chemical
products or detergents). To remove calcareous deposits, it is recommended to
use a mild acid such as lemon juice, followed by a thorough wipe down with a
damp cloth to remove any residue.
Saltwater aquariums
It is commonly known that salt water is far more corrosive, conductive (of electricity) and generally degrades both plastic and metal parts at an accelerated rate versus fresh water. To minimize salt accumulations on the Fluval Covers and on the LED Strip Light, it is recommended to take note of the following helpful tips:
- Make sure filter outputs do not spray above the water surface; position them below the water surface with a slight downward angle, but still allow for surface movement (contributes to oxygenation).
- If an air pump must be used, frequent removal of salt deposits will be necessary.
- Keep the water level as constant as possible (regular top-ups due to evaporation). This is beneficial in providing stable salinity and will help protect the cover.
- It is recommended to regularrly clean all LED Strip Light components that come into contact with salt water on a weekly basis. The cleaning should be carried out with a wet cloth (never use harsh chemical products or detergents). Simple lemon juice may be used to take away salt accumulation. Afterwards, rinse carefully to eliminate every residue of acid.
REPLACEMENT PARTS
Always use genuine Fluval Spare Parts to guarantee continued performance and safety. For a full listing of replacement parts, please visit www.fluvalaquatics.com
| Fluval Shaker 168| Fluval Shaker 252
---|---|---
2 x Top Sliding Covers| A13308| A13309
1 x LED Strip Light| A13246| A13247
1 x LED Driver| A20431| A20432
1 x Over Rim cable guide with bi-adhesive pad| A13865| A13865
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional Authorities. Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances.
2 – YEAR LIMITED WARRANTY
Your Fluval Aquarium and LED Strip Light are guaranteed for defective parts
and workmanship for a period of two years from the date of purchase. This
guarantee is valid with proof of purchase only. The guarantee is limited to
repair or replacement only and does not cover consequential loss, loss or
damage to livestock and personal property or damage to animate or inanimate
objects, irrespective of the cause thereof.
This guarantee is valid provided the aquarium is placed in a suitable location
that is flat and level and has been installed in accordance with the
installation instructions and care guide. This guarantee excludes aquarium
breakage due to misuse, chips, stress cracks caused by improper support or
other breakage. This guarantee is valid only under normal operating conditions
for which the unit is intended. It excludes any damage caused by unreasonable
use, negligence, improper installation, tampering, abuse or commercial use.
The warranty does not cover wear and tear, breakage of glass or parts which
have not been adequately or correctly maintained.
If at sometime in the future you have cause to claim under this guarantee, you
will need to provide proof and date of purchase. We recommend that you retain
your receipt for this purpose. Rolf C. Hagen Inc. wishes you many hours of
enjoyment with your Fluval aquarium.
FOR AUTHORISED GUARANTEE REPAIR SERVICE
For Authorised Guarantee Service, please return (well packaged and by
registered post) to the address listed on the last page enclosing dated
receipt and reason for return. If you have any queries or comments about the
operation of this product, please let us try to help you before you return the
product to your retailer. Most queries can be handled promptly with a phone
call. When you call (or write), please have all relevant information such as
model number, age of product, details of aquarium setup, as well as the nature
of the problem.
If you have any queries or comments about the operation of this product,
please contact your Specialist Aquatic Retailer in the first instance. Most
queries can be handled easily at store level. In the unlikely event that it
cannot, please return the item to the retailer, with your valid proof of
purchase, for repair or replacement under the two year warranty terms.
CANADA
CALL US TOLL-FREE AT:
1-800-554-2436
between 9:00 a.m. and 4:00 p.m. Eastern
Standard Time.
Ask for Customer Service.
FOR AUTHORISED GUARANTEE REPAIR SERVICE:
Return with dated receipt to:
Rolf C. Hagen Inc.
20500 Trans-Canada Hwy
Baie-D’Urfé, Québec H9X 0A2
USA
CALL US TOLL-FREE AT:
1-800-724-2436
between 9:00 a.m. and 4:00 p.m.
Eastern Standard Time. Ask for Customer Service.
FOR AUTHORISED GUARANTEE REPAIR SERVICE:
Return with dated receipt to:
Rolf C. Hagen (USA)
305 Forbes Blvd Mansfield, MA 02048
UK
Customer Services Helpline Number:
01977 521015. Between 9:00 AM and 5:00 PM,
Monday to Thursday and 9:00 AM and 4:00 PM
on Friday (excluding Bank Holidays).
Rolf C. Hagen (UK) Ltd, Customer Service
Department California Drive, Whitwood Ind Est.,
Castleford West Yorkshire WF10 5QH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>