FLUVAL T-Series Electronic Submersible Aquarium Heater Instruction Manual
- June 12, 2024
- FLUVAL
Table of Contents
T-SERIES
ELECTRONIC SUBMERSIBLE
AQUARIUM HEATER
INSTRUCTION MANUAL
#14880 T5O 5UsGal/50L
1488 T100 30 US Gal /100 L
40e? T15O 45 Us Gal /150L ;
BD 1200 608 &si7t001
T300 gous Gal / 00 L |
IMPORTANT SAFETY INSTRUCTIONS
WARNING – To guard against injury, basic safety precautions should be observed, including the following:
-
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
and all the important notices on the appliance before using the heater. Failure to do so may result in loss of fish life and/or damage to this appliance. -
DANGER – To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs yourself; return the appliance to an authorized service facility for service or discard the appliance.
A. If the appliance shows any sign of abnormal water leakage or if RCD (or GFCI – Ground Fault Current Interrupter) switches off, disconnect the power supply cord from main power supply and remove it from water.
B. Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet. Prior to installation, carefully check and make sure the glass tube is not fractured. WARNING! The heater casing is made of glass. Handle the unit with care at all times.
C. Do not operate any appliance if it has a damaged cord or plug, if it is malfunctioning or if it is dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the cord is damaged, the appliance should be discarded.
Never cut the cord.
D. To avoid the possibility of the appliance plug or electrical outlet getting wet, position the appliance to one side of a wall mounted outlet to prevent water from dripping onto the outlet or plug. A “drip-loop” (ill A) should be arranged. The “drip-loop” is that part of the cord below the level of the outlet, or the connector if an extension cord is used, to prevent water from traveling along the cord and coming in contact with the outlet. If the plug or outlet does get wet, DON’T unplug the electrical cord. isconnect the fuse or circuit breaker that supplies power to the appliance, then unplug and examine for presence of water in the outlet. -
WARNING – This appliance can be used by children aged from 3 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
To avoid injury, do not contact hot parts.
-
CAUTION – Always unplug or disconnect all appliances in the aquarium from electricity supply before placing hands in water, before putting on or taking off parts and while the equipment is being installed, maintained or handled. When inserting or
removing the heater from the water, always pull out the main electricity plug and do not pull the equipment out of the water until it has been allowed to cool for at least 30 minutes. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect. Always unplug an appliance from an outlet when not in use. -
This appliance is an aquarium heater for use in ornamental aquariums. Do not use this appliance for other than its intended use (i.e.: don’t use it with inflammable or drinkable liquids, in garden ponds, swimming pools, bathtubs, etc., or other situations where people are immersed). This appliance is suitable for use in water temperatures up to 35°C. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.
-
This heater is suitable for INDOOR/HOUSEHOLD use only. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.
-
Make sure that the heater is securely installed before operating it. The heater must be immersed in water at least up to the Minimum Water Level “min.” indicated (but without exceeding the depth of 39.5″ / 1 m). This aquarium heater must never operate outside of water (see illustration B).
-
If an extension cord is necessary, a cord with proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled. The connection should be carried out by a qualified electrical installer.
-
Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.
-
The power cord of this appliance cannot be replaced; if the cord is damaged, the appliance should be discarded. Never cut the cord.
-
CAUTION: This or any heater must never be operated outside of water.
-
CAUTION: To prevent corrosion or deterioration of materials that could lead to electric shock, use only with fresh water.
-
(For North America only) This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If the plug will still not
fit fully into the outlet, contact a qualified electrician to inspect the outlet and make the needed alterations. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
‘SAVE THESE INSTRUCTIONS
INSTALLATION
Note: It is recommended to fill the aquarium with water that is close to
the desired temperature you are trying to achieve. The aquarium heater must be
positioned to allow for free circulation of water around the glass heater
tube. Generally, the heater should be placed at the rear of the aquarium,
preferably close to a source of water movement to ensure even and thorough
distribution of warmed water. Be sure there are no rocks, decorations or
gravel obstructions touching the heater to create uneven heat in the glass
tube and weaken it.
CAUTION – Water level should never fall below the minimum water line
indicated on the glass heater tube. Always maintain the water level in the
aquarium to compensate for water loss due to evaporation.
Note: In absence of water the Fluval T-Series heater automatically cuts
power to prevent overheating.
-
Select the appropriate temperature by adjusting the Temperature Dial to the appropriate degree calibration.
-
Position the heater in the aquarium with the heater mounting bracket attached. Press suction cups firmly against glass to adhere to the aquarium wall. Wait 30 minutes before connecting to the electrical outlet. This allows the heater to adjust to the
aquarium water temperature. -
Note that it may take up to 12 hours for the heater to attain the water temperature you have selected. It is only after this time that the Temperature Dial dial should be adjusted to achieve a higher or lower temperature, as required.
-
The Heat indicator ring will illuminate in red when the unit is heating to initially achieve or subsequently maintain a set temperature. Once the selected temperature is attained, the unit will stop heating and the Heat indicator ring will illuminate in blue.
-
The temperature should be verified with an accurate thermometer after the heater has reached the desired temperature, before any fish are added to the aquarium, and throughout the life of the aquarium
MAINTENANCE
CAUTION: Unplug all appliances in the aquarium before placing hands in the water. Unplug the heater and allow it to cool for at least 30 minutes before taking it out of the water. Clean the heater regularly to remove deposits that could impair the heater performance. Deposits on the heater can be removed by soaking it in vinegar, then rinsing with fresh water before repositioning it in the aquarium. DO NOT USE chemical cleaners.
HEATER PERFORMANCE VARIABLES
This heater was designed to reach and maintain the set temperature, provided
that the maximum difference between the ambient and set temperature is less
than 10°F (6°C). Variables such as lower room temperature, wide temperature
fluctuations, lack of an
aquarium cover, presence of pumps and filters or aquarium placement in
proximity to cooling sources may require a higher wattage for proper control.
If the set temperature is not reached in all conditions, it will probably be
necessary to increase the heating
power.
NOTE: You may need to upgrade or add a second heater depending on ambient
room temperature. The heater cannot cool water from a higher temperature to a
lower temperature.
2 YEAR STANDARD WARRANTY
The Fluval Heater is guaranteed for defective parts and workmanship for a period of two years from the date of purchase. This guarantee is valid with proof of purchase only. The guarantee is limited to repair or replacement only and does not cover consequential loss, loss or damage to livestock and personal property or damage to animate or inanimate objects, irrespective of the cause thereof. This guarantee is valid only under normal operating conditions for which the unit is intended. It excludes any damage caused by unreasonable use, negligence, improper installation, tampering, abuse or commercial use. The warranty does not cover wear and tear, breakage of glass or parts which have not been adequately or correctly maintained. THIS DOES NOT AFFECT YOUR STATUTORY RIGHTS.
BONUS +1 YEAR
LIMITED TIME OFFER! Register this product online within 30 days of purchase
and Fluval will extend your current warranty at no charge. The extended
warranty is subject to provisions outlined within the standard Fluval
warranty. Complete details and registration available at:
FluvalAquatics.com/warranty EXTENDED
WARRANTY
FOR AUTHORIZED WARRANTY REPAIR SERVICE:
For Authorized Warranty Service please return (well packaged and by registered
post) to the address below enclosing dated receipt and reason for return.
If you have any queries or comments about the operation of this product,
please let us try to help you before you return the product to your retailer.
Most queries can be
handled promptly with a phone call. When you call (or write), please have all
relevant information such as model number, age of product, details of aquarium
set-up, as well as the nature of the problem.
CANADA: Consumer Repair, Rolf C. Hagen Inc., 20500 Trans Canada Hwy,
Baie-D’Urfé, QC, H9X 0A2 Canada only:
1-800-554-2436 between 9:00 a.m. and
4:30 p.m. Eastern Standard Time. Ask for Customer Service.
U.S.A.: Rolf C. Hagen (U.S.A.) Corp., 305 Forbes Blvd, Mansfield, MA
02048 U.S.A only: 1-800-724-2436
between 9:00 a.m. and 4:00 p.m. Eastern Standard Time.
Ask for Customer Service.
UK: Rolf C. Hagen (UK) Ltd, Customer Service Department, California Drive,
Whitwood Ind Est., Castleford, West Yorkshire WF10 5QH U.K. only: Helpline
Number 01977 521015. Between 9:00 a.m. and 5:00 p.m., Monday to Thursday and
9:00 a.m. and 4:00 p.m. on Friday (excluding Bank Holidays).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>