SW-MOTECH DGS.00.920.20100 Trax Adv Aluminum Case – System Silver 37/37 Instruction Manual

ANBAUANLEITUNG
mounting instructions
DGS.00.920.20100
contains
DGS.00.920.900.01.02 DGS.00.920.500.01
ALK.00.733.11000R/B ALK.00.733.11000L/B
ALK.00.733.15000/B KFT.00.152.35100
GPT.00.152.35100/B BC.ALK.00.732.10000/B
BC.ALK.00.732.10100/B BC.ALK.00.732.10700/B
BC.ALK.00.732.10300/B ALK.00.732.10200/B
Version Würfel

General
Display size (W/D/H): 52 x 75 x 18 cm
Options
Sales display with predefined placement per product world

• Rack, hooks and mounts included and free
• Costs: All products at usual conditions Sales display without equipment
• Equipment freely selectable, with own composition at POS
•  Costs: Rack 140€ plus VAT, mounts additional

Product worlds
TRAX ADV ALU-cases
Legend Gear LH-Bags

Display incl. equipment and mounts

Silver with accessories.
DGS.00.920.20100| Sales display cube with equipment. Theme: TRAX ADV 37/37l. Black with accessories.
DGS.00.920.20200| Sales display cube with equipment. Theme: TRAX ADV 45/45l. Silver with accessories.
DGS.00.920.20300| Sales display cube with equipment. Theme: TRAX ADV 45/45l. Black with accessories.
DGS.00.920.20400| Sales display cube with equipment. Theme: Legend Gear LH-Bag and accessories.
Theme| Preis (incl. VAT)
---|---
Theme: TRAX ADV 37/37l. silver with accessories.| 1. 563,00 €
Theme: TRAX ADV 37/37l. black with accessories.| 1. 563,00 €
Theme: TRAX ADV 45/45l. silver with accessories.| 1. 583,00 €
Theme: TRAX ADV 45/45l. black with accessories.| 1. 583,00 €
Theme: Legend Gear LH-bags and accessories.| 590,00 €

Display without products

TRAX ADV Alucase and accessories: Scope of delivery

Legend Gear LH-Bags

MOUNTING INSTRUCTIONS

Revision:00 – Datum / Date: 08 – 2020
Fitting equipment DGS subject KFT/GPT

MOUNTING

MOUNTING INSTRUCTIONS
Revision: 03 – Oatum ¢ Date: 02 – 2021
TRAX ADVENTURE ALU-BOX
ENGLISH – Thamk yow for choosing this premium product from SW-MOTECH.
Breese visit our webshop tor additions! infermotion, such as application charts sed POF mounting instructions. Any other decaments that may be required leg. ABE nel, are also available for dewnioad at our webshop. >> www.om- motech.com
Instaltation and/or maimtenaace ef this predect require geed technical understanding. For your own salety SW-NOTECH recommends having installotion and/or servicing carried out by & epeciotiol workshop.
‘SW-MOTECH assumes no titty tor damage caused by improper instaltation andjer maiatenance wark.
Carefully fellow ail the directions given in the mounting instructions. Also pay attention to all retevant information in the vehicie manual during Assembly. Hencentormsace can load to vehicle damage of sven endanger the driverl Pleese keep the mounting iastrections as reference. This product was developed fer vehicles in their originat condition. Compatibility with original accessory parts or other manufacturers accessory peris is net guaranteed. installed accessories can change driving behaviewr and/or stability of your vehicke.
GENERAL INFORMATION
Observe any country specilic legal or TUY regulations. If required, erter the installed parts into the vehicle decuments with the appropriate inspection authority.
SECURITY
Pleate pay attention to the following information concerning the TRAX
ADVENTURE ALU-BOX:
The TRAX ADVENTURE ALU-GGX is designed exclusively tor mounhng on SW-MOTECH GUICK-LOCK side carriers, QUICK-LOCK adapter plate an STEEL-RACK adapter kit, Modifications made to the cases wil void any warranty.
ATTENTION: Riding with TRAX ADVENTURE ALU-BOX may affect the motorcycle’s driving and braking performance.
ATTENTION: TRAX ADVENTURE ALU-BOXES M & L must be used in pairs.
Make cure the weight is eventy distributed between left and right aide case.
ATTEMTION: Maximam load: Please refer to the mounting instructions of the SW- MOTECH QUICK-LOCK side carrier, ALU-RACK of STEEL-RACK. Maxirourm speed with mounted cases: 130 kiavh 169 phi.
ATTEMTION: Hake sure that the TRAX ADVENTURE ALU-BOK is propeciy attached to the particular adapter and fully engaged to all feur mounting points! ALL latches of the TRAX ADVENTURE ALU-BOX must be locked BEFORE riding with the Trax @ EVO / TRAX ADW tock cylinder set (sold ‘separatety] and remain closed while riding. Impreperty meunted cates run the righ of detaching during transport.
CARE
To cloan the TRAX ADVENTURE ALU-BOX, use warm, soapy water and a soft, clean cloth, irse with clean water, Do NOT uve strong cleaning agents. rough cleaning tools or hagh pressure washer!

PARTS LIST

Seite
Page| Nr.
No.| Art.-Nr. / Bezeichnung Item No./ Description| Part| A
41
Quantity| N•m
---|---|---|---|---|---
6+7| (1-3|  | TRAX ADV ALU-BOX| 1 /1|
 |  |  |  |  |
5| (4)| ALK.00.733.041| Snap-Fit| 2/2|
 | (5)| ALK.00.733.040 (L/R)| Lid Limiter| 2/2|
(6)| ALK.00.733.042| Swivel Part| 2 /2|
(7)| 3 x 14; DIN 7500| Lenshead Screw, self-tapping| 4 /4| 0,5
 |  |  |

All measuremants in millimeters

• The second number indicates the total quantity of the listed part in the delivery.

TECHNICAL DETAILS

www.sw-motech.com
Bitte besuchen Sie unseren Please visit our webshop for

LID AND LOCK CYLINDER SET

Open the lid
(TRAX ADV M / L / topcase)

1. – Pull the latch of the lid upwards
2. and remove it from the latch bar.
3. Open the lid.

Insertion of the TraX ® EVO / TRAX ADV lock cylinder set *
(TRAX ADV M / L / Topcase)

1. – Insert the lock cylinders into the latches.

2. – Secure the lock cylinders with the clamping plates.
   ATTENTION: Pay attention to the correct alignment of the clamping plates (as shown in the detail drawings).

3.  Insert the keys into the lock cylinders; open or close the lock  cylinder as shown in the schematicdrawing.
   ATTENTION: Use for lubrication graphite powder ONLY! * Sold separately.

LID LIMITER

Mounting the lid limiters

(TRAX ADV M / L / top case)

1. – Open the lid. Attach the snap-fit (4] with the shown parts at the lid frame. Tighten the screws as specified in the parts list.
2. – Attach the lid limiters (5) with  the shown parts at the case frame. NOTE: Pay attention to left-rightspecifications for the limiters fin driving direction). Tighten the screws as specified in the parts list. Press the lid limiters onto the snap-fits.
3. Before closing the lid for the first time, the lid limiters must be compressed as shown in the drawing. While closing the lid, make sure that the lid limiters are not pinched between lid and case.
4. To remove the lid from the case  (as shown on page 5), rernove the lid limiters from the snap-fits first.

QUICK RELEASE FASTENER

Removing the lid
(TRAX ADVENTURE M /L)

1. – Press the quick release fastener down until it clicks into place and the button pops out.

2. – Then remove the tid fram the case.
   NOTE: if you have installed the lid limiters {5}, they must be detached before removing the lid [as shown on page 4).

3. – Press the button of the quick  release fastener to lock the replaced lid in place. Make sure that the quick release fastener snaps above.

Maintenance and cleaning of the quick release fastener
(TRAX ADVENTURE M /L)

1. – Loosen the six screws on the inner side of the case and remove the quick release fastener.
2.  Loosen the screw of the button {fix with thumb and index finger).
3.  Loosen the shown clip carefully and…
4. remove the quick release fastener and springs from the mounting plate.
5. Clean the components with clean water and let it air dry. Reattach all parts in reversed order.

MOUNTING

Attachement of TRAX ADVENTURE ALU-BOX M & L

1. – Lead the four openings of the mounting rails onto the locating bolts of the mounted QUICK-LOCK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly downward, until it properly rests on QUICK-LOCK side carrier.
   ATTENTION: Make sure that all four locating bolts rests on at the same time.

2. – Place the latch over the latch hook and…

3. – … close the latch; check the proper fit of the TRAX ADVENTURE  ALU-BOX on the QUICK-LOCK sidecarrier.
   ATTENTION: Make sure the closed latch is under sufficient tension! If  not the latch hook must bereadjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO /
   TRAX ADVENTURE lock cylinder set at the QUICK-LOCK side carrier before riding!

Attachement of
TRAX ADVENTURE ALU-BOXM &L

1. – Lead the four openings of the mounting rail onto the locating bolts of the mounted QUICK-LOCK adapter plate / STEEL-RACK adapter kit.
   Then press the TRAX ADVENTURE ALU-BOX slightly forward, until it properly rests on QUICK-LOCK adapter plate / STEEL-RACK adapter kit.
   ATTENTION: Make sure that all four locating bolts rests on at the same time.

2. Place the latch over the latch hook and …

3. close the latch; check the proper fit of the TRAX ADVENTURE ALU-BOX on the QUICK-LOCK Adapter Plate / STEEL-RACK Adapter Kit.
   ATTENTION: Make sure the closed latch is under sufficient tension! If not the latch hook must be readjusted!
   ATTENTION: Secure the TRAX ADVENTURE ALU-BOX with the separately available TraX ® EVO /
   TRAX ADVENTURE lock cylinder set at the QUICK-LOCK adapter plate / STEEL-RACK adapter kit before riding!

MOUNTING INSTRUCTIONS
Revision: 02 – Datum / Date: 06 – 2018
Adapter kit for PRO side carrier –
TRAX ADV/ION/EVO
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required le.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehictes in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts fe.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority. PREPARATION: Read the mounting tnstructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or teplaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

Schritt
Step| Nr.
No.| Art.-Nr. / Bezeichnung • Item No. / Description *| Artikel| Part| Quantity| N.m ‘
---|---|---|---|---|---|---
| (1)| KFT.00.152.070L / R| ; links / rechts| Latch Hook; left / right| 2 /2|
(2)| M6 x 16; ISO 7380| | Lenshead Screw| 4 /4| 9
(3)| KFT.00.152.071| | Guide Bolt| 8 /a|
(4)| M6 x 20; DIN 7991| | Countersunk Screw| 8 /a| 9
(5)| M6; DIN 6927| | Lock Nut with Flange; black| 12 /12|
| | | | |

• All measurements in millimeters. – ** The second number indicates the total quantity of the part in the delivery.
  *** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The illustration shows the mounting to the right PRO side carrier. Mount the parts to the left PRO side carrier in the same way as to the right PRO side carrier. Attach the shown parts to your PRO side carriers (sold separately). Tighten the screws as specified in the parts list.
ATTENTION: To ensure the proper fit of your TRAX ADV / EVO / ION side case, adjust the latch hook (1) over the elongated holes (see detail drawing)! Make sure that the side case’s latch engages properly when mounted!

MOUNTING INSTRUCTIONS
Revision: 00 – Datum / Date: 01-2018
Adapter kit for ADVENTURE-/STREET-RACK
– TRAX
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no Liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting Instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not
guaranteed. Furthermore, BEFORE installing this product, make sure that alt moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as weil as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be feinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure ail threads, unless otherwise specified, veith medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manutacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previousty removed are properly replaced. Also make sure that na moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functians. After the first 50 km and then at regular intervats, check the tightening torque af all screw connections and the proper fit of the product.

Schritt
Step| Nr.
No.| Art.-Nr. / Bezeichnung • Item No. / Description •| Part| Quantity “| N.m ‘
---|---|---|---|---|---
| (1)| ALK.00.165.010| Latch Hook| 1 /1|
(2)| M6 x 16; ISO 7380| Lenshead Screw| 2 /2| 9
(3)| M6; DIN 6927| Lock Nut with Flange| 2 /2|
(4)| ALK.00.165.083| Guide Bolt| 4 /4|
(5)| ALK.00.165.084| Plastic Cap| 4 /4|
(6)| M6 x 20; DIN 7991| Countersunk Screw; black| 4 /4| 7
(7)| M6; DIN 985| Lock Nut| 4/4|
| | | |

• All measurements in millimeters. – ** The second number indicates the total quantity of the part in the delivery.
  *** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

ADVENTURE RACK
Attach the shown parts to your ADVENTURE RACK (sold separa- tely).
ATTENTION: Use liquid thread locker [screws (6) only]!
Tighten the screws as specified in the parts list.
ATTENTION: To ensure the proper fit of your TRAX ADV/EVO/ION topcase, adjust the latch hook (1) over the elongated holes [see detail drawing]! Make sure that the topcase’s latch engages properly when mounted!

Adapter plate for STREET-RACK Attach the shown parts to your adapter plate for STREET-RACK (sold separately).
Tighten the screws as specified in the parts list.
ATTENTION: To ensure the proper fit of your TRAX ADV/EVO/ION topcase, adjust the latch hook (1) over the elongated holes [see detail drawing)! Make sure that the
topcase’s latch engages properly when mounted!

MOUNTING INSTRUCTIONS

Revision:01 – Datum / Date: 08 – 2014
TraX ® Gear Plus Lid Innerbag
TraX ® Gear Plus Innerbag
ENGLISH – Thank you for choosing this quality product from SW-MOTECH.
The TraX ® Gear Plus Bag is designed exclusively for use with the TraX ® ALU- BOX.
SECURITY
Please pay attention to the following product information:
Modifications will void any warranty.
ATTENTION: Riding with the TraX ® Gear Ptus Bag may affect the motorcycle’s driving and braking performance.
ATTENTION: Maximum load (TraX ® Gear Plus Lid Innerbag): Please refer the manual instructions of the QUICK-LOCK EVO Side Carriers and the TraX ® ALU- BOX, but not more then 1 kg. The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION: BEFORE riding make sure that the TraX ® Gear Plus Lid Innerbag is properly attached. Check the proper fit at each stop!
ATTENTION: All parts of the TraX ® Gear Plus Bag must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from the exhaust and remain clear of the exhaust stream. All strap ends should be secured so they can not blow around once the vehicle is in motion. Dropping the motorcycle or improper handling can damage the outer surface of the TraX ® Gear Plus Bag.
Never store pointy or sharp-edged objects in bags, which could cause injury to persons or damage to the vehicle/product.
Care
To clean the TraX ® Gear Plus Bag, use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Clean the TraX ® Gear Plus Bag after riding in salty conditions, to avoid damage from salt.
ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors [e.g., SMOG, acid rain, etc.)! SW-MOTECH assume no liability for this.

Munting

TraX ® Gear Plus Lid Innerbag (BC.ALK.00.732.10100/B)
ATTENTION: Only for TraX ® ADVENTURE ALU-BOX! Place the TraX @ Gear Plus Lid
Innerbag on the inner side of the TraX ® ALU-BOX lid.
Fix the straps of theTraX ® Gear Plus Lid Innerbag to the tie-down points of the lid, as shown in the drawing.
Now pull the straps until the Trax ® Gear Plus Lid Innerbag is centered  and sits tightly. Make sure there are no loose strapends.

MOUNTING INSTRUCTIONS
Revision: 0% – Datum / Date: 11-2020
TRAX M/L expansion bag
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or sven endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
SECURITY
Please pay attention to the following product information:
Moditications will void any warranty.
ATTENTION: Riding with the TRAX expansion bag may affect the motorcycle’s driving and braking performance.
ATTENTION: Maximum loed: Please refer the manual instructions of the SW- MOTECH side sarriers and the TRAX aluminium case, but not more then 2kg. The maximum vehicle load specified by the manufacturer must not be exceeded!
Maximum speed with mounted TRAX expansion bag: 130 km/h! ATTENTION: BEFORE riding make sure that the TRAX expansion bag is properly attached. Check the proper fit at each stop!
ATTENTION: All parts of the TRAX expansion bag must not contact any hot or moving parts of the vehicle. All parts should also remain S cm away from the exhaust and remain clear of the exhaust stream. All strap ends should be secured so they can not blow around once the vehicle is in motion. Dropping the motorcycle or improper handling can damage the outer surface of the
TRAX expansion bag.
Never store pointy or sharp-edged objects in bags, which could cause injury to persons or damage to the vehicle/product.
CARE
To clean the TRAX expasion bag use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Clean the TRAX expansion bag after riding in salty conditions, to avoid damage from salt.
ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors le.g., SMOG, acid rain, etc.)1 SW-MOTECH assumes no liability for this.
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces. Make sure that all areas of the case, which have contact with the product, are protected with an adhesive protection film from scratches and abrasions. SW-MOTECH assumes no Liability for paint damage and abrasions.

FIXATION

Place the TRAX expansion bag on the lid of the TRAX aluminium box or a similar aluminum case.
Fix alt four straps of the TRAX expansion bag to the tie-down points of the lid, as shown in the lower detail drawings.
Now tighten the straps until the TRAX expansion bag is centered and sits firmly on the lid. Make sure that the strap ends are secured against fluttering.

MOUNTING INSRUCTIONS

Revision: 00 – Datum / Date: 10-2015
Passenger Backrest TRAX ADV Topcase
Thank you for choosing this premium product from SW-MOTECH.
@ Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications}, are also available for download at our webshop. >> www.sw-motech.com
Installation and/or maintenance of this product require good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Instalied accessories can change driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration or operation as well as TUV regulations where appticable. If required, register installed parts in the vehicle documents together with the appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Make sure to use only the appropriate tools. During installation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strong strength liquid thread locker. If not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and nuts must be tightened according to DIN/ISO specifications. After installation make sure that all parts and hardware previously removed are properly replaced.
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed and function of the vehicle is nat hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. Regularly check (every 100 km) for the proper seating of all parts and connections removed during installation.

‘ Step| Nr.
No.|  No./ Description| Part| Quantity| N-M
---|---|---|---|---|---
3| (1)| ALK.00.732.900.01| Upper Backrest| 1 /1|
 | (2)| ALK.00.732.900.02| Lower Backrest| 1 /1|
(3)| M6 x 10; ISO 7380| Lenshead Screw; self-sealing, black|  5 /5| 5,5

All measuremantts in millimeters

MOUNTING

Attention: Before mounting check the dimensions of the templates to make sure the scale is correct!
Cut out the templates carefully. Place the templates on the TRAX ADV Topcase and fix them with adhesive tape, as shown in the drawing. Use a non-permanent marker to
mark the five drill positions.

Check the distance between the marked drill positions with the templates. Now drill the holes from the outside into the TRAX ADV Topcase at the marked positions (borehole diameter 6,5 mm).

Mount the upper (1} and lower (2) Backrest onto the TRAX ADV Topcase, as shown in the drawing.
ATTENTION: Use liquid thread locker! Tighten the screws as specified in the parts list.

Datum der Konfektionierung / Date of packaging:
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany
Tel. / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com

References

• Modesto Technologies
• SW-MOTECH Shop - qualitativ hochwertiges Motorradzubehör

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>