MASTER BUILDER MasterFiber 143 Reinforcing Sprayed and Cast Concrete Owner’s Manual
- September 13, 2024
- MASTER BUILDER
Table of Contents
MASTER BUILDER MasterFiber 143 Reinforcing Sprayed and Cast Concrete
Polypropylene fiber for reinforcement in sprayed concrete and cast concrete applications as an alternative and/or supplement to existing concrete reinforcement products
Material Description
MasterFiber 143 is engineered for use as a secondary reinforcement to control
shrinkage, settlement, and temperature cracking both in sprayed and cast in-
situ applications. The inclusion of MasterFiber 143 in a concrete mix will
contribute to improving the durability of concrete through increased crack
propagation resistance and its energy absorption characteristics. The fibres
will disperse uniformly throughout the concrete mix and act as an anchoring
mechanism within the cement matrix thereby improving the toughness and
ductility of the material.
MasterFiber 143 can maximize concrete service life by providing superior
resistance to attack from damaging environmental elements such as water,
chlorides, and corrosive environments such as sewerage conduits and/or saline
water.
Areas of Application
MasterFiber 143 is appropriate for use in ground-supported slabs, industrial flooring, pavement, and precast elements. MasterFiber 143 can also be used in shotcrete applications for increased energy absorption and reduced rebound.
MasterFiber 143 increases:
- Concrete durability
- Toughness
- Post-residual flexural strength
MasterFiber 143 decreases:
- Hardened shrinkage
- Shotcrete rebound
- Manual labour
Characteristics and Benefits
- Easy to dose either at the batch plant or on-site concrete mixer truck before application
- Only minor impact on flow & slump properties of fresh concrete
- High resistance to acid/alkalis attack suitable for use in wet underground conditions and subsurface constructions exposed to damp conditions
- Reduces labor, construction, transport, and storage costs compared to a solution with conventional reinforcement
Properties
Polymer type | Virgin polypropylene |
---|---|
Color | Colourless |
Shape (Cross section) | Rectangular |
Shape (Longitudinal) | Straight |
Surface | Embossed |
Thickness (approx.) | 0.6mm ± 10% |
Width (approx.) | 1.2mm ± 10% |
Length | 47mm |
Tensile strength (EN14889-
| 550 MPa
Modulus of Elasticity
(EN14889-2)
| 10 GPa
Density| 0.91g/cm3
Melting point (°C)| Approx. 170°
Acid/alkali resistance| High
No. of fibres per kg| 28000
Dosing & Batching
Add fibres to the concrete mixer after water and admixtures. After addition of the fibres mix for at least 2-3 minutes to ensure even distribution of fibres within the concrete mix. Note that in the event that a slight slump loss is experienced after the addition of the fibres – the mix design should be reviewed such to allow for fibre inclusion and avoidance of addition of extra water. Site trials with the intended concrete mix design must be conducted to verify and determine the performance of the fibre with the proposed sprayed concrete mix. It is recommended that where automated fibre dosing systems are utilised, that they be checked for suitability and calibrated accordingly.
Polypropylene fibre for reinforcement in sprayed concrete and cast concrete applications as an alternative and/or supplement to existing concrete reinforcement products
Packaging
1 pallet of MasterFiber 143 is made up of:
- 114 x 5kg munchable boxes = 570kg per pallet
- 228 x 2.5kg munchable boxes = 570kg per pallet
Each pallet is covered by a waterproof cover. MasterFiber 143 is wrapped in water-soluble PVA to form bundles.
Storage & Shelf Life
MasterFiber 143 is to be stored undercover and protected from the weather.
Note
Field service support, where provided in no way constitutes supervisory
responsibility. For additional information please contact your local Master
Builders Solutions representative. MB Solutions reserves the right to have the
true cause of any technical challenge determined by an accepted test method.
Disclaimer
STATEMENT OF RESPONSIBILITY
The technical information and application advice given in this MB Solutions
Australia Pty Ltd publication are based on the present state of our best
scientific and practical knowledge. As the information herein is general, no
assumption can be made as to a product’s suitability for a particular use or
application, and no warranty as to its accuracy, reliability, or completeness
either expressed or implied is given other than those required by law. The
user is responsible for checking the suitability of products for their
intended use and for ensuring that the application and use of the productares
by the manufacturer’s guidelines and recommendations.
NOTE
Field service where provided does not constitute supervisory
responsibility. Suggestions made by MB Solutions Australia Pty Ltd either
orally or in writing may be followed, modified, or rejected by the owner,
engineer ,or contractor since they, and not MB Solutions Australia Pty Ltd,
are responsible for carrying out procedures appropriate to a specific
application.
MB Solutions Australia Pty Ltd ABN 69 634 934 419
Unit 102, 2 Burbank Place
Norwest NSW 2153
Freecall: 1300 227 300
www.master-builders-solutions.com/en-au
| MB Solutions New Zealand Ltd 45C William Pickering Drive Albany, Auckland
New Zealand
Phone: +64 9 414 7233
| Emergency Advice:
1300 954 583 within Australia (24hr)
0800 001 607 within New Zealand
---|---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>