antaira 2S RS232 Multi Serial PCI Express Card Installation Guide
- June 6, 2024
- antaira
Table of Contents
2S RS232 Multi Serial PCI Express Card
Installation Guide
INTRODUCTION
Congratulation on your purchasing this high performance PCI Express multi- serial host adapter. The adapter is high speed PCI Express bus based and plug- and-play compliant. Its serial ports are fully 16C950 UART compatible with most of the RS232C devices available from the market.
Features:
- Full x1 PCI Express Throughput, 250Mbytes/sec
- Fully Compliant with PCI Express Base Specifications, Revision 2.0 Gen 1
- 256-byte FIFO UARTs, Fully Compatible with 16C950, Baud Rate up to 921.6Kbps
- Data Bits: 5, 6, 7, 8, 9
- Parity: Even, Odd, None, Space and Space
- Supports 2 RS232 ports over 2 DB9-male Connectors
- Supports Win 2000, XP, 2003, 2008, Vista, Win 7, 8.x, 10 and Linu x
BOARD LAYOUT
J5: Aux. Power Connector
JP3: Aux Power Source Selector
JP2 : Jumpers to Enable/Disable Power over pin 9 for S1, S2
S1: Port-1 Connector
S2: Port-2 Connector
JUMPER SETTINGS
- JP2: – Pin-9 Power Setting Jumpers for S1and S2: The design of each DB9 male connector has an option to supply DC power to its Pin-9. Pin number 9 of the DB9 connector was defined for RS232 RI (Ring Indicator) signal. Since some applications do NOT use this signal, in this case, Pin-9 can be used to deliver DC power for the serial devices. This product provides 2 settings for the power, +5V
and +12V. The default factory setting was set at “DIS” (RI signal), i.e. no power supplied on the DB9M connector’s Pin-9.
Pin-9 Power Setting Table:
JP2
|
Jumper Settings
---|---
No Power Supplied on Pin-9 of both S1 and S2 (Default)|
S1’s Pin-9 has power, S2’s doesn’t have|
S2’s Pin-9 has power, S1’s doesn’t have|
- JP3 – AUX. POWER Source Selector:
JP4
|
Settings
---|---
External 5V : Power source is +5VDC, from J5 AUX power connector.
(Default)|
External 12V : Power source is +12VDC, from J5 AUX power connector.|
Internal 12V: Power source is +12VDC, from PCIe golden finger
(motherboard’s PCIe slot)|
SOFTWARE DRIVE INSTALLATION
Note:
PLEASE DO NOT LET WINDOWS AUTO SEARCH THE DRIVERS ON THE CD, it will
cause problems because the INF files will be conflict in this case.
Instead, please browse to the correct location (folder) manually to make sure
the correct drivers are chosen and installed correctly.
Drivers are in each corresponding folder
DB9 (MALE) PIN ASSIGNMENTS
SPECIFICATIONS
Type
|
Specifications
---|---
Connectors
Bus Interface
Number of Ports
RS-232 Signals
Baud Rate
Data Bits
Stop Bits
Parity
Flow Control
Power Requirement
Operating Temperature
Operating Humidity
Storage Temperature
| DB9 Male
PCI Express x 1
2
TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND
110 bps to 921.6Kbps
5,6,7,8,9
1, 1.5, 2
None, Even, Odd, Space, Mark
RTS/CTS, XON/XOFF
3.3V/150mA
0 to 55 °C(32 to 132° F)
5 to 95% RH
-20 to 85°C(-4 to 185°-F)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>