SCHLAGE FBE479AACENLAT625 Sense Century Touchscreen Smart Deadbolt Installation Guide

SCHLAGE FBE479AACENLAT625 Sense Century Touchscreen Smart Deadbolt Installation Guide

Tap or click here

Schlage Sense™

Installation Instructions

Package Contents

Camelot Style shown throughout guide.

Let’s get started!
Once you have all your tools together, please follow each step carefully and in order. Because this is an electronic lock, the order of steps is very important. If you skip a step, you may have to perform a factory default reset and start over.

You will definitely need this tool:

• Phillips screwdriver You can use a manual or electric screwdriver, but please DO NOT use a power drill!

You may also need these tools:

• Tape Measure
• Flathead Screwdriver
• Pencil
• Wood Block
• Hammer

INSTALLATION NOTES! PLEASE READ!

• DO NOT use a power drill for installation! This could damage the lock.
• Please read all the instructions before calling customer support.
• DO NOT install the batteries before installing the lock! Follow the instructions in order!
• If you have previously installed this lock on another door, you MUST perform a Factory Default Reset FIRST! See the User Guide for more information.
• This lock is designed for the following operating temperatures:
  • Outside Lock Body (exterior mounted): -31°F (-35°C) to 151°F (66°C)
  • Inside Lock Body (interior mounted): 14°F (-10°C) to 120°F (49°C)

1 Download the app.

Download the Schlage Sense app from the App Store and on Google Play. Just search for “Schlage Sense” to find the app.

Be sure to accept any available firmware upgrades. The app will alert you to upgrades and walk you through the process.

The Schlage Sense app works on iPhone®, iPad®, and iPod touch® with iOS 9.3 or later or devices with Android 5.0 or later. Google Play and the Google Play logo are trademarks of Google Inc.

2 Watch the installation video.

You can access installation videos in the app! The videos will give you a good overview of the installation process. Alternatively, please visit answers.schlage.com and then click on Schlage Sense.

3 Check current door/frame alignment.

Because the bolt on this lock is extended automatically, it is important that the door and frame are aligned. Use this checklist to determine if your current alignment will work without any adjustment.

□ I can lock the door without pushing, pulling or lifting the door.
□ My door alignment–the ability to lock the door easily and smoothly–stays the same with changing seasons.
□ When the door is closed, there is space for the deadbolt to extend 1″ into the frame when locked.

If you could not check every box in the checklist, you will need to adjust your door and/or frame. Please visit answers.schlage.com for more information.

4 Remove the current deadbolt from the door.

Remove the entire deadbolt, including the bolt. You may also want to remove the strike.

» In order to maintain BHMA Grade 1, you must install the included reinforcement plate and strike (see step 7d on page 7).
» A standard Schlage deadbolt is shown. Check with your specific deadbolt manufacturer if you need help.

5 Check door/frame dimensions.

Measure the dimensions shown. If your door dimensions do not match, you will need to change your door preparation. Go to answers.schlage.com for drilling instructions.
Toll-Free Calling From: U.S.A.: 888-805-9837 Canada: 800-997-4734 Mexico: 018005067866

» If your door is thicker than 1³/”, you will need a thick door kit. Please call Customer Service:

» Mark your cross bore and backseat measurements on this page. You will need these measurements for installation. Either measurement is normal.

6 Locate programming and access codes.

Codes are located on the stickers on the front of the User Guide. You will need these codes to operate the lock. They are also located on the back of the Alarm Assembly.

» Do NOT remove these stickers from the back of your lock! If you lose your codes, you can reset your lock back to these default codes.

» To connect your lock to your iOS or Android phone, follow the instructions in the Schlage Sense app. You will use the Home Kit™ setup code or the Programming Code to complete pairing.

7 Install bolt and strike.

7a Adjust bolt length, if necessary.

• If the backseat (see step 5 on page 5) of your door was 2³/” (60 mm), you do not need to do anything. Proceed to step 7b.
• If the backseat (see step 5 on page 5) of your door was 2³/” (70 mm), you need to adjust your bolt. Twist the faceplate until the button pops into the 2³/” space.

7b Change the faceplate, if necessary.

» In step 7c, your installation will depend on which kind of door edge you had in this step.

7c Install the bolt into the door.

Choose the picture below that matches your door.

7d Install the strike into the frame.

Install all the parts shown for maximum security.

» In order to maintain BHMA Grade 1, you must install the included reinforcement plate and strike.

» The reinforcement screws may not fit on doors with sidelights.

7e Test bolt alignment.

1. Close the door.
2. Insert a flathead screwdriver into the slot in the bolt, as shown.
3. Rotate the screwdriver toward the door edge to extend the bolt into the hole in the frame. This operation should be smooth. You should be able to rotate the screwdriver 90°, fully extending the bolt.
4. If the operation was not smooth, or if the bolt did not fully extend, adjust your frame and/or door preparation. Go to answers.schlage.com and watch the video Proper Alignment of Door and Frame for a Smoothly Operating Lock for further instructions.
5. Retract (unlock) the bolt before continuing to step 8.

» If the deadbolt continues to rub against the strike, contact Customer Support for an alternate strike with an additional .060″ (2 mm) clearance.

8 Install the Touchscreen Assembly.

8a Install the Touchscreen on the outside of the door.

Always remove the spacer for a 1¹/” (38 mm) cross bore. See Spacer Removal on page 14 before continuing.

» The clips snap into the cross bore (see step 5 on page 5) to assist in holding the keypad on the door.

» The Touchscreen Assembly should install smoothly. If it does not, check that the bolt is set to the correct backseat (see step 7a on page 6).

» NOTE: If you have a cross bore (see step 5 on page 5) that is slightly less than 2¹/” (54 mm), the lock may not install smoothly. You can remove the spacer.

8b Install the Support Plate on the inside of the door.

» Make sure the Touchscreen and Support Plate are straight on the door before tightening the screws. Tighten screws fully to prevent the lock from moving over time.

9 Install the Alarm Assembly.

9a Remove the battery cover from the Alarm Assembly.

9b Connect the cable to the Alarm Assembly.

» Locate the screws in step 9d before beginning this step so they will be handy when you need them.

9c Install the Alarm Assembly.

1. Align the tab with the notch as shown.
2. Route the cable into the channel.
3. Then slide the Alarm Assembly toward the door.

9d Secure the Alarm Assembly to the Support Plate.

Install the lower screw first.

10 Install the Batteries.

10a Install the batteries into the battery tray.

1. Unsnap the connector.

2. Remove the battery tray.

3. Install four high-quality alkaline AA batteries.
   » Lithium batteries may cause undesirable operation.

4. Carefully replace the battery tray, with the batteries facing the door.

5. Snap the connector back into place.

10b Install the battery cover.

11 Set up the Lock.

1. Open the door if it is not already open.
2. Press the Outside Schlage Button.
3. Enter one of the default access codes into the lock (see label shown in step 6 on page 5).
4. The lock will perform a setup routine. Wait until the bolt stops moving before continuing.
   » If the Touchscreen did not light up during this step, you may have a power problem. Install fresh batteries and make sure the battery wires are connected (see step 10a on page 11). If that does not help, make sure the cable is connected and is not crimped (see step 9b on page 10).

12 Test the Lock.

CAUTION
Keep the key with you during testing to avoid being locked out!

» For complete information about programming and light/beep patterns, see the Manual Programming Guide and Troubleshooting sections in the User Guide.

12a Extend the bolt (lock) using the inside thumb turn.

12b Extend the bolt (lock) using the Touchscreen.

12c Retract the bolt (unlock) using the Touchscreen.

answers.schlage.com

12d If the lock failed to lock or unlock:

1. If the Touchscreen did not light up, you may have a power problem. Install fresh batteries and make sure the battery connector is connected (see step 10a on page 11). If that does not help, make sure the cable is connected to the Alarm Assembly and is not crimped (see step 9b on page 10).
2. If the lock had power but you need to adjust your door/frame, please go online to answers.schlage.com for complete adjustment instructions and videos.

Spacer Removal
(Option for small crossbones only)

13 Continue to the User Guide.

Your lock is installed and functional. Continue to the User Guide for complete information about how to configure and operate the lock and alarm.

Questions about your new
Schlage Sense™ Smart Deadbolt?
Please don’t return it to the store!
Let us help you first!

Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Home Kit is a trademark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google Inc. Android is a trademark of Google Inc.

Need Help?
For technical documents and videos, visit schlage.com or download the Schlage Sense app.

U.S.A.: 888-805-9837 Canada: 800-997-4734 Mexico: 018005067866

If you have questions about any part of installation or programming, don’t return your Schlage Sense™ to the store. Our Schlage Customer Service representatives are ready to help.
Toll-free: 888-805-9837
answers.schlage.com

A NEW KIND OF KEYLESS.

© Allegion 2017 Printed in U.S.A. P518-398 Rev. 06/17-a

References

• Contact us | Schlage Door Locks Customer Support
• Door Locks, Entry Door Knobs & Hardware for Doors | Schlage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>