K M 19775 Tablet PC Stand Instruction Manual

: June 6, 2024
: K M

K M 19775 Tablet PC Stand

Thank you for choosing this product. Please read and follow the instructions carefully. They inform you about all the important steps concerning assembly and handling. We recommend you to keep them for future reference.

INTENDED USE

Universal tablet holder for all tablets sized approximately 10″ to 16″.
Particularly suited for tablets with a protective cover or casing up to 20 mm.

FEATURES & CAPABILITIES

Flexible and stable! Your Tablet PC is an absolute eyecatcher.
Equally suited for stage, home, rehearsal room and studio.
The clamping mechanism (including side safety bracket) enables the simple, effective and secure mounting of your Tablet PC.
Overlapping clamping jaws with integrated a moss rubber layer provide a secure hold, eliminate vibration noise and protect the tablet casing.
With adjustment options that leave nothing to be desired:
Tablet size, angle of inclination, direction, portrait/landscape: all individually adjustable
The tablet holder is attached to a stable, height-adjustable (710-1560 mm) stand, foldable for transport and storage (packing size ø 90 x 563 mm)

SAFETY INSTRUCTIONS

a. Load capacity: – suited for Tablets from 10″ to 16″
– Clip Tablet carefully into mounting plate and check for secure fit
– Handle the holder with care, especially when changing the settings:
– inclination, format, direction, height
b. Surface: – should be suited, i.e., a level and stable surface is a prerequisite
c. Installation: – always hand-tighten the screw connections on the stand and bracket backlash free
d. Various influences: – protect against wind, moisture, agitation, vibrations, etc.

INSTALLATION INSTRUCTIONS

COMPONENTS

Please visually check whether all parts are present and in good order – as far as can be seen.
a. STAND
a.1 3-leg with PA base
a.2 3-rod combination
a.3 Connection thread – 3/8″
b. TABLET CRADLE
b.1 Swivel joint with 3/8″ threaded bush
b.2 Cradle (base, slider, clamp)
b.3 Guard arm with felt and rubber cap

PREPARE STAND

2.1 Fold feet apart
2.2 Loosen base screw and move base down as far as it will go; retighten the base screw
2.3 NOTE! Stand wobbles
The base tube of the stand is not allowed to touch the ground, in fact the stand should rest securely on the three base tube parquet protectors
2.4 Loosen the knurled screws, adjust the extensions to the desired height; clamp the knurled screws again

Connect the TABLET CRADLE with the STAND

3.1 Turn the knurled disc on the threaded bolt a.3 as far as it will go .
3.2 Now also screw the swivel joint b.1 to the threaded bolt of the stand, but not quite up to stop (approx. 2 – 3 turns)
3.3 Turn the knurled washer back again, so that it is clamped backlash- free with the swivel joint
3.4 Tighten the wing nut

TABLET PC POSITIONING

Generally suitable for TABLET PCs from 10″ to 16″ screen size (see Chapter 7).
4.1 Always position the TABLET PC in the CRADLE in a centered and balanced position
4.2 NOTE
Off-center positioning may be necessary due to the size of the TABLET PC. Please observe the balance of the entire installation for safety reasons
4.3 The Guard arm should always rest against the TABLET PC and…
4.4 …must be at the bottom – as additional safety – if the TABLET PC is set upright!

NOTE!
If the Tablet PC is placed almost cantered but the guard arm does not rest 4.3 we recommend to rebuild the arm, as described in chapter 5.

REBUILD the GUARD ARM

First remove the tablet from the holder b.2

5.A DISASSEMBLING the GUARD ARM
5.1 Slightly loosen the clamping nut…
5.2 …and extend the slider completely
5.3 Retighten the clamping nut
5.4 Push the lever down and hold
5.5 Shift the tablet cradle b.2 upwards as far as it will go until the connection disengages with an distinguishable click
5.6 Lift tablet cradle b.2
5.7 Remove Guard arm b.3
5.8 If required, the swivel joint b.1 can be unscrewed from the stand a
5.B REATTACHING the GUARD ARM
5.9 Insert guard arm b.3 into the corresponding a recess of the swivel joint b.1. NOTES:
5.10 Select the position of the arm b.3 so that the tablet PC sits in the centre of the holder and attaches sideways to the rubber of the bracket
5.11 The guard arm should be attached to the swivel joint b.1 with at least 2 boreholes.
5.12 We advise not to fit the guard arm with only one borehole, since the joint would feel loose.
5.C REASSEMBLY the TABLET CRADLE
5.13 Place the tablet cradle b.2 on the 4 hooks of the swivel joint b.1
5.14 Then push the tablet cradle b.2 down as far as it will go.
Pay attention to the clicking noise.

INSERT TABLET PC

6.1 Tilt cradle b.2 backwards approx. 30°…
6.2 Tighten clamp of swivel joint b.1
6.3 Place Tablet on lower supports…
6.4 …and lean on cradle b.1
NOTE:
The Tablet PC should rest:
a. at the BACK,
b. CENTERED and
c. against the GUARD ARM b.3. Depending on the size of the Tablet PC, the position of the guard arm should be corrected (see Chapter 5 )
6.5 Loosen the clamping of the slider…
6.6 …and retract the slider until the upper attachment of the Tablet PC is securely fastened to the cradle b.2. In this process, the slightly compressed foam rubber coating clamp the tablet.
6.7 Tighten the clamping again
6.8 Check firm seat of the tablet and readjust, if necessary.
6.9 The foam rubber pads protect the surface of the tablet and provide additional clamping.
6.10 Remove the tablet in reverse order.
NOTE: Please hold the tablet securely, especially when opening the clamping 6.5.

TABLET PC DIMENSIONS

The clamping range includes:
7.1 – in depth up to 20 mm
7.2 – in width from 150 – 430 mm
7.3 – in height from 158 – 280 mm
7.4 – in diagonal approx. 10″ – 16″

ADJUSTMENTS

When adjusting
8. TILT
9. FORMAT
10. DIRECTION the TABLET PC can remain in the holder.

TILT

The TABLET PC can be fixed in any position between vertical and horizontal end position.
8.1 Hold Tablet and loosen wing nut,
8.2 tilt Tablet as desired and…
8.3 …retighten wing nut

FORMAT

The Tablet PC holder has a 90° swivel function.
9.1 Hold the tablet and turn it to lands cape or portrait mode – or position at an angle!
Invisible stops in the swivel joint limit the rotation
9.2 NOTE:
Install guard arm c so that the stop is at the bottom when the tablet is aligned vertically; if necessary, the guard arm must be inserted into the swivel joint rotated by 180° (see Chapter 5)

DIRECTION

10.1 Initial position:
The knurled disc and the swivel joint of the cradle are clamped together
10.2 First release the tension by unscrewing the knurled disc
10.3 Turn the Tablet PC stand holder in the desired direction
10.4 Tighten knurled disc and the swivel joint together again
ALTERNATIVE:
10.5 Change the direction of the tablet by repositioning the complete stand (without fig.)
NOTE:
10.6 For safety reasons, the swivel joint must always be mounted with at least two turns on the threaded bolt of the stand.
See also Chapter 2 of the instructions

SETTINGS – OVERVIEW

MAINTENANCE

Careful handling maintains the function and safety of the installation
Regularly check the proper condition of the components; defective parts must be – replaced or repaired
Ensure that the screw and plug connections are firmly seated before use
Always remove the tablet PC first when carrying out maintenance and cleaning work
For cleaning and maintenance, use a slightly damp cloth and a non-abrasive – cleaning agent

FAULT-FINDING (F) and REPAIR (R)

F: Stand wobbles
B: Check floor levelness and load capacity
B: Ensure 3-leg support – base tube should not touch the surface 2.3
B: Tighten the knurled screws of the clamps

F: Tablet PC sits off-centre
B: Position guard arm b.3 accordingly (Chapter 4 and 5 )
B: Tablet PC wider than 330 mm (7.2)

F: Tablet PC wobbles
B: Set slider tighter (6.6)
B: Clamping too loose, tighten if necessary (6.7)
B: Tablet PC is smaller than the min. dimension of 158 mm (7.3)

F: Tablet PC holder wobbles
B: Swivel joint b. 1 screwed too loosely to the stand
B: Check connection and tighten if necessary (Chapter 3 and 10 )
B: Not properly engaged? Place cradle b.2 and engage it correctly 5.C

F: Cradle b.2 cannot be pulled off swivel joint b.1
B: First press lever, then unlock cradle b.2 and pull off 5.4 and 5.5

TECHNICAL DATA

Material| Base, swivel joint, handles: Polyamid (PA)
Tablet cradle: Bio-based plastic
Tubes, guard arm, screw connections: steel, brass
Clamps: Zinc die-cast
Caps, foam rubbers, rubber washers: TPE, EPDM, TPU
---|---
Load capacity| Tablet PCs (check dimensions)
Dimensions| for Tablets ~10″ – 16″
width 150-330/430 mm, height 158-280 mm, depth: 20 mm
Stand: Height 600-1450 mm, root circle-ø 565 mm
Thread BSW 3/8″
Installation: Height 710 – 1560 mm
Cardboard| 920 x 120 x 180 mm
Weight| net: 1.8 kg, gross: 2.1 kg