K M 19761 Smartphone Halter User Manual

KM 19761 Smartphone holder

Specifications

• Material: Clamping screw, threaded bolt: Steel; Smartphone holder, holding arm, ball adapter, clamping screw, clamp: Plastic; Holding arm, inside: Aluminum rod
• Load capacity: Smartphones and similar devices
• Dimensions and adjustment range: 80 x 75 x 173 mm
• Packaging Weight: 0.21kg

Product Usage Instructions

Mounting:

1. Unpack and check the product for any damage and completeness.
2. Smartphone holder holding arm with clamp:
3. Connect the smartphone holder with the ball adapter:
4. Open the clamping nut on the smartphone holder in the UNLOCK direction until the ball adapter snaps into place.
5. Tighten the clamping nut in the LOCK direction. To adjust the position, loosen the clamping nut, set the desired position, and hand-tighten it.
6. Mounting on the stand:
7. Open the clamping screw on the clamp.
8. Place the clamp on the stand tube and tighten the clamping screw at the desired position.
9. Note: The clamping jaws of the holding clamp must be aligned axially to the stand tube.
10. Place smartphone:
11. Press the quick-out button to move the clamping jaws on the smartphone holder apart.
12. Fold the support feet outwards, and place the smartphone on the support feet.
13. Press the two clamping jaws onto the smartphone.

Maintenance, Cleaning, and Repair:

• Maintenance: Regularly check if the screw connections are tight.
• Cleaning: Use a slightly damp cloth to clean the smartphone holder. Avoid chlorinated or abrasive cleaning agents as they can damage the surface and varnish.
• Repair: Immediately repair any damage that occurs and stop using the smartphone holder. Maintenance workshould only be carried out by individuals with necessary knowledge.

FAQ

• What is the load capacity of the smartphone holder?
  The smartphone holder is suitable for holding smartphones with a width of 45-90 mm and similar devices. Please ensure not to exceed this range for optimal performanc

• How do I adjust the position of my smartphone once it is placed in the holder?
  To adjust the position of your smartphone, loosen the clamping nut, set the desired position, and hand-tighten it. Ensure not to open the clamping and adjusting screws while the smartphone is inserted.

• Can I clean the smartphone holder with abrasive cleaning agents?
  No, it is recommended to avoid using chlorinated or abrasive cleaning agents as they can cause damage to the surface and varnish of the smartphone holder. Use a slightly damp cloth for cleaning instead.

Intended use

The smartphone holder is suitable for holding a smartphone with a width of 45-90 mm. Similar devices can also be clamped. Thanks to the versatile adjustment possibilities, the operating ele-ments on the smartphone remain accessible. With the holding clamp, the holder can be attached to tubes with a diameter of 10-30 mm. Thanks to the flexible holding arm and the ball adapter, in-dividual adjustment is possible.

Foreseeable misapplication

• Do not open the clamping and adjustment screws while the smartphone is inserted.
• Do not use the smartphone holder overhead.

General

• Use a suitable stand: It must have sufficient stability and load-bearing capacity. For this,
• observe the usage information of the stand used.
• Set up and adjustment:
  • Attach the holder to the stand without the smartphone and set the desired position.
  • When the smartphone is clammed it is only allowed to loosen the clamping and adjustment
  • screw to carry out small corrections regarding the position. Increased caution is required
  • during correction, to prevent the device from falling unexpectedly.
• The smartphone holder must be protected from falling, dirt, moisture and jerky movements.
• Do not handle with excessive force.
• The usage information is an integral part of the product and should be kept for its service life or passed on to any subsequent owner or user.

Warranty

No warranty is given for damage caused by:

• Non-observance of the usage information and the “General safety and assembly instructions”.
• Unsuitable or improper use.
• Incorrect installation or commissioning by the buyer or third parties.
• Natural wear and tear.
• Careless handling.
• Improper modifications or repair work by the buyer and third parties.
• Impact on components of foreign origin.
• Use of non-original spare parts.
  Modifications, additions and conversions that may impair safety are prohibited without the manu-facturer’s approval.

Technical data

Material

| Clamping screw, threaded bolt: Steel

Smart phone holder, holding arm, ball adapter, clamping screw, clamp: Plastic

Holding arm, inside: Aluminum rod

---|---
Load capacity| Smartphones and similar devices
Dimensions and adjustment range| Smartphone holder: 45-90 mm Holding clamp: diameter 10-30 mm Vertical and horizontal: 360°
Packaging| 80 x 75 x 173 mm
Weight| 0.21 kg

Mounting

To mount the smartphone holder, proceed as follows:

1. Unpack and check product for damage and completeness

2. Connecting the smartphone holder with the ball adapter

3. Open the clamping nut on the smartphone holder in the UNLOCK direction until the ball adapter 2 snaps into the smartphone holder with slight pressure.

4. Hand-tighten the clamping nut in the LOCK direction.

5. To adjust the position, loosen the clamping nut, set the desired position, and hand-tighten the clamping nut.

6. Mounting on the stand

   • The stand is properly set up.
   • The stand has the necessary load-bearing
   • capacity.
   • The stand is set up on a level and load-
   • bearing surface.
     Open the clamping screw on the clamp 1.
     Place the clamp on the stand tube 2, and tighten the clamping screw at the desired position 3.
     Note: The clamping jaws of the holding clamp must be aligned axially to the stand tube.

7. Place smartphone
   Holding arm with smartphone holder is properly attached to the stand.

   • Press the quick-out button 1 to move the clam-ping jaws on the smart phone holder apart.
   • Fold the support feet outwards 2, and place the smart phone on the support feet 3. Press the two clamping jaws onto the smart phone 4.
     Note: The back of the smart phone must lie flat against the smart phone holder and rest against the support feet. The holding arm can be bent up to 90° in any direction. This requires some effort. Preferably, the desired position is to be set via the ball adapter.

Maintenance, cleaning and repair

• Maintenance: Regularly check if the screw connections are tight.
• Cleaning: Use a slightly damp cloth to clean the smartphone holder. Do not use chlorinated or abrasive cleaning agents. These will cause damage to the surface and varnish.
• Repair: Immediately repair any damage that occurs and stop using the smartphone holder. Maintenance work may only be carried out if you have the necessary knowledge. If any parts are missing, contact the manufacturer at www.k-m.de. Here you can find a corresponding spare parts list by entering the article number on the type label. Use this page to reorder missing or damaged components.

Fault and troubleshooting

Smartphone holder wobbles

| ●  Check the stability and screw connection of the used stand.

●  Check the screw connections on the smartphone holder and tighten if necessary.

Smartphone wobbles in the holder| ●  Adjust or retighten the seat of the lateral stops.

Storage, disposal

Store the smartphone holder in a dry place.
Recycle disassembled components:

• Scrape all components made of metal.
• Recycle or reuse all plastic, paper, and cardboard components.
• Sort all other components according to material composition and dispose of them according to local regulations.

ABOUT COMPANY

• KÖNIG & MEYER GmbH & Co. KG
• Kiesweg 2
• 97877 Wertheim
• Germany
• Phone: +49 9342/8060
• Fax: +49 9342/806-150
• E-Mail: contact@k-m.de
• Web: www.k-m.de

References

• König & Meyer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>