K M 19789 Tablet PC Stand with Boom Arm Instruction Manual

June 15, 2024
K M

K M Logo 19789 Tablet PC stand with boom arm »Biobased«K M 19789 Tablet PC Stand
with Boom Arm

Information for use

Intended use

The tablet PC stand is above all designed to hold a tablet with 155-307 mm dimension. The stand features a heavy cast-iron base, making it highly versatile to use and extremely stable. Height and incline can be adjusted individually thanks to the extension tube and boom arm. The joint on the holder can be used to further adjust the angle.
Foreseeable misapplication
Do not transport the tablet PC stand with the tablet clamped. Please do not use the tablet PC stand upside down. Do not use the tablet holder sideways; there is nothing to keep the tablet from sliding out

General

The stand must have sufficient stability. The flooring must be clean, dry, even and load-bearing.
  ● High-value and/or sensitive floor coverings should be protected with a suitable under-lay.
● The surface of the base may leave marks on these types of floors.
  Using the tablet PC stand with inserted tablet can affect the stability and the stand may lose its balance.
  Set up and adjust:
● Attach the holder without the tablet to the stand and adjust to the desired position.
● Loosening the clamping and adjustment screw when the tablet is still clamped, is only per-
● mitted to make small corrections to the position. Increased caution is required when making
● this correction to prevent the unit from falling down unexpectedly.
● Whenever a clamp is loosened, the part that is coming loose must always be held/secured.
The fixed support arms of the tablet holder must always be aligned toward the floor.
● To change between portrait and landscape position, the tablet must be reinserted to deter-
● mine the alignment.
Falling over or dropping the tablet PC stand holder can cause personal injury and damage to property.
There is a risk of crushing between the components due to the possibility of adjustment.
The user must be physically and professionally fit.
  The usage information is an integral part of the product and should be kept for its service life u or passed on to any subsequent owner or user.

Warranty

No warranty is given for damage caused by:
Non-observance of the usage information and the “General safety and assembly instructions”.
  Unsuitable or improper use.
Incorrect installation or commissioning by the buyer or third parties.
Natural wear and tear.
  Careless handling.
  Improper modifications or repair work by the buyer and third parties.
  Impact on components of foreign origin.
Use of non-original spare parts.
Modifications, additions and conversions that may impair safety are prohibited without the manufacturer’s approval.

Technical data

Material| Base tube, extension tube, swivel joint: powder-coated steel, black Screws, washer, threaded bolt, nut: galvanised steel Clamping screw press-in nut: brass
Knurled washer: anodised aluminium, black Holder, upper joint part, lower joint part, clamping screws, clamping sleeve, boom arm sleeve, safety ring: black plastic
---|---
Load capacity| Tablets 10″ – 16″
Dimensions and adjustment range| Base diameter: 300 mm
Tablet clamping range: Upper hole (1): 185-307 mm Lower hole (2): 155-277 mm
Maximum thickness: 20 mm Height, floor to center of tablet holder: 700-1520 mm Min./max. height: 1000 mm/1625 mm Angle at tablet holder: 220°
Packaging| Package 1: 990 x 370 x 49 mm, package 2: 201 x 155 x 94 mm
Weight| 5.8 kg

Assembly

!There is a risk of crushing between the components due to the adjustment option!

  1. Unpack and check item for damage and completenessK M 19789 Tablet PC Stand with Boom Arm - riskThis item consists of 2 packages.
    Package 1: Base, extension tube, boom arm
    Package 2: Tablet holder

  2. Assembling and installing the stand Set the rod combination on the base 1 and screw fully into the base 2.
    Set the boom arm on the extension tube 3 and screw fully together with the extension tube 4.
    Set the tablet holder on the boom arm tube 5 and screw fully together with the boom arm tube 6.

  3. Inserting and adjusting the tablet
    The stand must be properly set up.
    The stand must be placed on a level surface that can hold the weight involved.
    The desired position must be set.
    The clamping screws must be clamped.

K M 19789 Tablet PC Stand with Boom Arm - stand 1

Open the lock nut at the slider 1 and pull the slider upward 2. Set the tablet on the lower holder arms and place it in the tablet holder 3. Make sure the back of the tablet lies flat against the holder. Set the slider on the tablet 4 and handtighten the lock nut 5. Z The clamping range can be ad- justed using the two drill holes. To do this, unscrew the lock nut 1. Remove the screw from the first hole (1) and insert it into the second (2), for example. Screw the lock nut into place
Adjusting the inclination of the tablet holder:
The lock nut on the holder can be used to adjust the inclination. To do this, open the lock nuts 6, set the desired position 7 and hand-tighten the lock nuts again 8. Making adjustments at the pivot joint: The pivot joint can be used to set the inclina-tion and extension. Loosen the clamping screw 9, set the desired position 10 and re-close the clamping screw 11.
Note: The boom must always be held when making any adjustment to the pivot joint. When the clamping screw 9 is opened, the boom moves freely in terms of extension, incline, and rotation. Make sure the holder arms of the tablet holder are inclined toward the floor. Making adjustments at the extension tube: Loosen the clamping sleeve 12, set the height and alignment using the extension tube 13 and re-close the clamping sleeve 14.

Maintenance, cleaning and repair

Maintenance: Regularly check if the screw connections are tight.
Cleaning: Use a slightly damp cloth to clean the tablet PC stand . Do not use chlorinated
 or abrasive cleaning agents. These can cause damage to the surface and varnish.
  Repair: Immediately repair any damage that occurs and stop using the tablet PC stand.
  Maintenance work may only be carried out if you have the necessary knowledge. If any parts
are missing, contact the manufacturer at www.k-m.de. Here you can find a corresponding
  spare parts list by entering the article number. Use this page to reorder missing or damaged
  components.
Fault and troubleshooting

Fault/cause Check/Remedy
Tablet cannot be clamped in the holder ● Check the clamping range, if

necessary adjust the clam-  ping range on the slider with the help of the second hole.
Tablet PC holder is unstable or wobbles| ● Check surface for irregularities or dirt.
● Check the screw connection between the base rod and base and tighten if necessary.
● Check the screw connections and retighten if necessary.
Tablet does not hold in position once set| ● Check clamping screws on the tablet holder and swivel  joint and tighten if necessary.
● Tighten clamping sleeve on base tube if neces-sary.

Storage, disposal
Store the tablet PC stand in a dry place.
Recycle disassembled components:

  • Scrape all components made of metal.
  • Recycle or reuse all plastic, paper, and cardboard components.
  • Sort all other components according to material composition and dispose of them according to local regulations.

Contact information
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2
97877 Wertheim
Germany
Phone: +49 9342/8060
Fax: +49 9342/806-150
E-Mail: contact@k-m.de
Web: www.k-m.de
19789-000-55 Rev.04 03-80-967-00 9/23

Documents / Resources

| K M 19789 Tablet PC Stand with Boom Arm [pdf] Instruction Manual
19789 Tablet PC Stand with Boom Arm, 19789, Tablet PC Stand with Boom Arm, PC Stand with Boom Arm, Boom Arm, Arm
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals