SYNCO G1 2.4Ghz Wireless Lavalier Microphone User Manual

SYNCO G1 2.4Ghz Wireless Lavalier Microphone User Manual

Caring For Your SYNCO Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping, impact of external force.
• Do not attempt to disassemble the product. Doing so voids warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions happened.
• Failure to follow all the instructions may result in mechanics damage.
• Warranty does not apply to human errors.

Package List

Product Instruction

1. External Mic Input
2. USB-C Port
3. Power
4. Reset(Help with Eject Pin)
5. Low Cut
6. Pairing
7. Built-in Mic
8. Pocket Clip
9. Pairing Indicator
10. Power Indicator

1. USB-C Port
2. Power(Mono/Stereo Switch)
3. Reset(Help with Eject Pin)
4. Channel A Gain Control
5. Channel B Gain Control
6. 3.5mm Audio Output
7. 3.5mm Monitoring Jack
8. Pocket Clip
9. Pairing Indicator
10. Power Indicator

Indicator

Operations

1. Power Button
   Long press the power button for2 seconds to turn on/off the system. Short press the power button on the RX for Mono/Stereo switch.

2. Pairing
   The system will pair automatically after power on. If you need manual pairing, long press the channel A gain control and channel B gain control on the RX, and the pairing button on the TX, the system will start to pair.

3. Connection
   The receiver outputs audio signals to recording devices with a 3.5mm TRRS Phone Cable or a 3.5mm TRS Camera Cable. Please use the corresponding cable based on your device.

4. installation
   Attach the transmitter or the external mic to the speaker’s clothing. Install the receiver to the camera’s hot shoe via the pocket clip.
   ( Note: When using the external mic, please insert it into the mic input properly.)
   

5. Gain Control
   The initial value of the gain is the microphone’s original volume. Each press of the gain control button increases the gain by one level, fourth level at most. When the gain is at max level, press once and return to initial value.

6. Charging
   Please fully charge the TX and RX via the USB-C port and the charging cable before use.

Specifications

Setting The Recording Level Correctly

Camera devices generally have poor-quality, noisy preamps. In order to get the cleanest signals possible, it is highly recommended that you set the recording level on your camera quite low, 1/2 or 1/3 of it.
Gl provides variable gain control, allowing you to tailor your levels to just about environment and recording device.

Adjust the recording level of inbuilt mis for SONY Camera
(Take A 7S II for example)

(Take EOS 50 Mark IV for example)

(Take LUMIX GH5 for example)

Warranty

Warranty Period

Thank you [or purchasing SYNCO products .

1. defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYN CO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user  Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

• Faults resulted from inappropriate use of a product without following its operation specification
• Artificial damage, e.g. crash, squeeze, scratch, or soaking
• Modifications to a product by its user or a third party without prior written consent of SYN CO, e.g. replacement of element or circuit, label alteration
• The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
• All consumable accessory attached to a product, like cab le, wind muff, battery
• Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

• If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at support@syncoaudio.com.
• Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
• If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.

support@syncoaudio.com

support@syncoaudio.com
www.syncoaudio.com
https://www.facebook.com/syncomicrophones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>