SYNCO G3 Microphone User Manual
- June 3, 2024
- SYNCO
Table of Contents
Microphone G3, » USer Manual
G3 Microphone
Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein.
- Please keep the praduct In a dry, clean, dust-free environment.
- Keep corrosive chemicals, liquids and heat souroc away fram the Product to prevent machanics damage.
- Use only a soft and dry cloth for claaning the product.
- Malfunction may be caused by dropping, impact of external forcs.
- Do not attempt to disassemble the product, Doing so voids warranty.
- Please have the product checked or repaired by authorized technicians if any malfunctions happened.
- Failure to follow all the instructions may result in machanics damage.
- Warranty does not apply to human errors.
Package List
Product Introduction
TX Transmitter
- Volume Control Button
- Built-In Mic
- Switch Button
- 3.5mm Monitoring Port
- Recording Button
- Pocket Clip
- Contacts (For Charging And File Transmission)
RX Receiver
- Switch Button/Back Button
- Setting Button
- Up Option Button
- Down Option Button
- Display Screen
- Type C/Digital Output Port
- 3.5mm TRS/TRRS Output
- 3.5mm Monitoring Port
- Rx Built-In Mic
- Pocket Clip
TX Indicator
Working Indicators
| Blue/green indicator on transmitter corresponds to the A/ B transmitter
shown on the receiver screen
---|---
Blue/green indicator flashes| The transmitter waiting for connection
Blue/green indicator keeps on| The transmitter successfully connected to the
receiver
Blue/green indicator lights up and flashes at the same time| Reset completed
Orange indicator on| Charging
Orange indicator off| Ful y charged
Recording Indicators
| Red indicator on| Recording on
Red indicator off| Recording off
Operations
Tx Transmitter
-
Power On
Method 1 : Push out the TX upwards in the direction shown in the figure. The TX automatically powers on and the blue and green indicators light up and flash.
Method 2: Long press the switch button on the front of the transmitter for 3 seconds, and the blue and green indicators light up and flash. -
Power Off & Charging
Method 1 : Slide the TX into the receiver in the direction shown in the figure, and the orange indicator lights on for automatic charging. The orange indicator turns off and the TX automatically shut down when fully charged.
Method 2: Long press the switch button on the front of the TX for 3 seconds, the blue/green Indicator turns off, and the TX shut down. Method 3: The TX automatically shuts down in 5 minutes when there is no connection or recording. -
Reset
The TX automatically power on when took out from the RX. Long press the switch button for 3 seconds to shut it down, then long press the switch button for 8 seconds until the blue and green indicator flashe. Reset completed. -
Recording
Recording on: Long press the recording button on the side of the TX for 3 seconds until the red light on. Recording off: Long press the recording button for 3 seconds until the red light tums off. Note: A single recording audio file lasts for a maximum of 22 hours (48K16bit) -
File
Transfer Put back the TX into the RX and set the card reading mode in the RX to read the files. -
Monitoring
Insert the listening device into 3.5mm monitoring port for the RX input sound, such as the RX microphone sound/the RX input audio from mobile phone. Adjust the five-level monitoring volume when press the volume button on the TX.
Note: This port of the TX is used as output only, not input.
RX Receiver
-
Power On /Off Long press the power button on the RX for 3 seconds until the screen turns on/off to switch on/off.
-
Reset Press the up and down buttons for 8 seconds to reset the RX when power on.
-
Paring Automatic paring: Take out the TX after turn on the RX, the TX will automatically turn on and pair with the RX. Manual pairing:
Method 1: After the RX turns on, enter the setting panel for pairing without taking out the transmitter,
Method 2: Take out the TX and reset it first. Enter the setting panel for when the receiver powers on. -
File Transfer
1 Connect the Type-C port of the RX to the output of the mobile phone/ computer through adaptor cable.
2 Connect the 3.5mm OUT output port of the RX to the device such as camera through TRRS/TRS cable.
3 The 3.5mm monitoring port of the RX is used for monitoring and can be set as the TRS output port in the Settings panel. The output LR has 3 channels: TXA- TXB-RX. The device supports a maximum of 3 outputs, and the output devices corresponding to TRRS and TRS channels can be combined freely. -
Monitoring 3.5mm Monitoring port of the RX supports 32 w earphones for in-ear monitoring to mobile phone input or computer input audio.
Display Screen
1 Transmitter A
2 Transmitter B
3 Transmitter Signal Transmitter Power
5) Transmitter Power Level
6 Sound Effect Of Left Channel
7 Gain Value Of Left Channel
8 Sound Effect Of Right Channel
9 Gain Value Of Right Channel
10 Receiver
11 Receiver Power| 12 Power Level Of Receiver Microphone Power Level
13 Gain Value Of Receiver
14 Frequency Setting/ Version Information
15 Output Channel Option
16 0SB Port Output Gain
1 3.5Mm Port Output Mode
183.5Mm Port Output Gain
19 Monitoring Port Output Mode
20 Output Channel Option
21 Monitoring Port Volume
---|---
Interface Selection and Button Operation
- Press the Setting button or the Up and Down Option button. The screen highlights shows the selected panel.
- Press the Up and Down option buttons to switch the panel, and then press the Settings button to select the operation page of the settings panel.
- On the operation page, press the Up and Down button to switch between different parameter categories. Press the operation button again as the screen flashes as a prompt. Press the Up and down option key to switch between different options of this parameter.
- Press the Power/Return button to retum to the previous stage.
Setting Content Description
-
When the TX A/B memory card is full, the icon will blink red. After selecting the panel of TX A/B, press the setting button to enter the operation page to mute the microphone and view the recording duration.
-
On the operation page of the RX panel, you can mute the receiver microphone and modify the gain.
-
Enter The Operation Page Of The Channel Panel:
(1) The noise reduction gear of the channel can be changed. There are three level noise reduction: 75/150/300.
(2) The high frequency lifting of the channel can be set on/off.
(3) 5 EQ sound effects can be selected for the channel.
(4) The gain adjustment of the sound channel can be set.
-
Enter the frequency setting operation panel to open the frequency and view the version. When the frequency matching function is enabled, a status pop-up will be displayed, indicating the frequency matching succeeds or fails.
-
The output panel operation page is displayed. The output of the 3.5mm port is (TRRS/TRS), and different microphones are selected for different channels.
The function of type -C port is as follows: charging only/ data reading + charging/ reading L transmitter memory file/ reading R transmitter memory file/ mobile phone mode. NOTE:
1. Select Phone mode in the Setting if heat occurs when using the Apple adapter or Type-C connection to the phone. In this case, the phone will not supply power to the receiver in reverse, reducing the heat generated by the interface, and the phone will powered up longer.
2. Please check whether the receiver is set to TRRS, when using 3.5 TRRS audio cable to connect mobile phone. (TRRS is for mobile phone, TRS is for camera). -
Enter the operation page of the monitoring panel, you can adjust the monitoring volume of the receiver and switch the monitoring port mode. After the 3.5mm monitoring port is set from monitoring to output, the output mode and volume are associated with the setting of the out port.
Specifications
TX Transmitter
Wireless Transmission | Digital 2.4GHz |
---|---|
RF Frequency Band | 2.4G |
Working Distance | 820tt/250m(LOS area) |
Sampling Rate | 48KHz |
Bit Depth | 16Bit |
RF Output Power | 20dB |
Battery Capacity | 260mAh, Lithium Battery, |
Monitor | 3.5mm In–Ear monitoring |
Monitor Volume | 1-5 level |
Built–in Memory | 8G |
Battery Charging Time | 2H |
Battery Life | 5H |
Dimensions | 622220mm |
Material | ABS |
Weight | 15g |
Microphone
Form Factor | MEMS Silico Mic |
---|---|
SNR | > 75dB |
Polar Pattern | Omnidirectional |
Frequency Range | 50-20KHz |
Sensitivity | -28dB (±3dB, re 1 V /Pa at 1 KHz) |
Maximum SPL | 11 OdB SPL (at 1 KHz) |
RX Receiver
Wireless Transmission | Digital 2.4GHz |
---|---|
RF Frequency Band | 2.4G |
Working Distance | 820ft/250m(LOS area} |
Sampling Rate | 48KHz |
Bit Depth | 16Bit |
Display Screen | 1 8″ (240*160) |
Number of Input Channels | 3 |
Number of Output Channe | 3 |
Monitoring | 3.5mm In–Ear Monitoring |
Monitoring Volum | 0-15 level |
Audio Output | TXA+TXB/RX |
Audio Output Volum | -40dB-0dB |
ANC | 75/150/300 |
High Frequency Boost | 4K |
Environment Scene Sound | Popular, Blues, Scene, Rap, Country |
Power Requirements | 5V 1A |
Battery Type | Built-in Lithium Battery, 1800mAh |
Battery Charging Time | 2 5H |
Battery Life | 13H |
Dimensions | 6462+28mm |
Material | ABS |
Weight | 74g |
Microphone
Form Factor | Electret Condenser Mic |
---|---|
SNR | > 75dB |
Polar Pattern | Omnidirectional |
Frequency Range | 50-20KHz |
Sensitivity | -420d8 (±308, re 1V/Pa at 1KHz) |
Maximum SPL | 11 0dB SPL (at 1KHz) |
WARRANTY
Warranty Period
Thank you for purchasing SYNCO products.
- Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
- Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
- Faults resulted from inappropriate use of a product without following its operation specification
- Artificial damage, e.g. crash, squeeze, scratch, or soaking
- Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration
- The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
- All consumable accessory attached to a product, like cable, wind muff, battery
- Faults as a result of force majeure, such as fire, flood, lightning, etc.
Warranty Claim Procedure
- If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at support@syncoaudio.com.
- Please retain your sales receipt and warranty certificate as proof of purchase If any of these documents is missing, only sales return or chargeable service will be provided.
- If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.
WARRANTY CERTIFICATE
Please register your warranty Meanwhile, you are welcomed to contact us via
Email: Support@syncoaudio.com
USER INFORMATION
Customer Name————
Phone Number.——————–
Email:—————-
Address:———-
Sales Date—————————
SALES INFORMATION
Model.——————
Product Code·———————
Dealer:——————–
Service Date:——————
Technician:———-
REPAIR RECORD
Issue.——————
RESULT
Solved Unsolved Returned(Replaced)
Guangzhou Zhiying Technology Co., Ltd
Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi
Avenue, Liwan District, Guangzhou, China, 510000
support@syncoaudio.com
www.syncoaudio.com
https://www.facebook.com/syncomicrophones
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>