Aerpro Integrated Touch Screen Control Kit FP8419K Instruction Manual

FP8419K
Integrated Touch Screen Control Kit
for Ford Vehicles

1. Fascia Panel
2. Right Bracket
3. Left Bracket
4. Four Switch Trim
5. Back Cover
6. PCB Spacer
7. Pocket

APPLICATION| Note : Application data is subject to change at any time
---|---
Ford Mustang| 2015>| (Right Hand Drive Models Only)
RECOMMENDED TOOLS

• Panel Removal Tool

|

• Screwdriver

|

• Cutting Tool

FEATURES

• Allows for the installation of a double-DIN aftermarket stereo
• Replaces HVAC control unit
• Retains climate controls, steeringwheelcontrols, heated seats, vehicle OE personalization menus, and settings
• Accommodates OEM toggle or OEM push button switches
• Includes mounting brackets and fitting accessories
• Finished in gunmetal to match the vehicle dashboard

DISCLAIMER
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the
vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.

PRIOR TO INSTALLATION

Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product.Connects2 can not be held responsible for the installation of this product.

WARNING
DASH MODIFICATIONS REQUIRED FOR FULL INSTALLATION OF A DOUBLE DIN STEREO WHEN USING THIS PRODUCT See Step 7 forDetails

INSTALLATION GUIDE

1. Remove the two (passenger and driver side) knee panels on the lower console. (A) Next, remove the two exposed screws (B)

2. Using a panel removal tool, carefully remove the tray located below the USB and 12V socket ports, then remove and retain the two exposedscrews.
   Lift and slightly pull back the center cup holder console but do not remove the console.
   

3. Using a panel removal tool, carefully remove the air vent trim surrounding the vents, temp, and boost control gauge. Unplug and remove.
   

4. Unclip and remove the plastic plate located in between the USB plug-in and the cigarette lighter

5. Remove the four screws securing the OEM panel to the dash (circled), then unplug and remove the panel

6. Remove the OEM display and the CD receiver by unscrewing the four screws for each component, then unplug all wiring and remove.
   *DASH MODIFICATION**

7. Carefully cut and remove the highlighted dashed area on the sub-dash frame to create space for the double DIN stereo.
   File down the ridge areas highlighted and note the image.
   NB: Only file down the amount of plastic necessary to achieve a flush fit
   

8. Remove the ten screws and the 12V socket located behind the OEM climate control panel and retain them for installation. Then remove the PCB board back cover.
   NB: The amount of screws may vary between vehicle models.
   

9. Remove the five screws securing the PCB board to the panel, then remove them from the panel
   NB: The amountof screws may vary between vehicle models
   

10. Lift and remove the plastic CD insert slot away from its location

11. Lift and remove the drive train/ignition controls and rubber pad from the OEM panel and retain them for later install
    NB: Remove rubberband plastics blocking pieces needed in order to remove the ignition controls
    

12. lace the drive train/ignition control trim into the fascia panel
    

13. Place the OEM drive train/ignition control buttons (retained in Step 11) into the trim from Step 12.
    Next, place the three provided PCB spacers indicated by the arrows on top of the button controls.
    NB: Image is for illustration purposes only and may not represent the vehicle’s exact ignition control button configuration

14. Place the rubber pad from the OEM drive train controls onto the back of the buttons, being careful not to knock over the spacers placed in the previous step.
    

15. Carefully align the circuit board over the rubber pad
    

16. Place the back cover plate over the PCB and secure using the six screws retained in the disassembly
    NB: Use the screws attained from the OEM PCB cover plate

17. For Single DIN Installation:
    Attach the brackets provided to the pocket (A), then secure the stereo to the brackets (B). Lastly, secure stereo assembly into dash cavity (C).
    
    For DoubleDIN Installation:
    Attach the brackets provided to the aftermarket stereo (D), then secure stereo assembly into dash cavity (E).

18. Connect and reassemble everything in the reverse order of disassembly to complete the installation
    NB: 12V/cigarette plugins retained from OEM panel

CONNECTING THE PATCH LEAD

Here are some examples of how to make various patch leads:
Example 1: Alpine -Cut Link J2, then use the Jack Connector
to connect the patch lead to the head unit
Example 2:Kenwood -Cut Link J1 and J2, then use the
wire connector to connect the patch lead to the head unit

STEERING WHEEL CONTROL CONFIGURATION

1. Track
2. Volume +
3. Track +
4. Volume
5. Voice Command(For JVC/Alpine/ Pioneer Units with Voice Command Capabilities)
6. Mute
7. Hang Up (BT HU Only)
8. Pick Up (BT HU Only)

WIRING DIAGRAM

CLIMATE/CONVENIENCE CONTROLS

The touchscreen interface replaces the factory climate, convenience, and personalization controls built into the factory Ford stereo/dash panel. This solution provides improved ergonomics whilst adding touchscreen capabilities unique to this system. Read the following sections to familiarise yourself with the operating controls and settings.

1. Change on-screen button configuration to show controls for heated and cooled seats (if the vehicle is equipped). Levels for both driver and passenger side seats can be adjusted up or down independently.

2. Access menu. See ‘Menu Structure’ for more

3. Quick press four times and hold to enable Installer Menu. The Installer Menu can be found un­der ‘Vehicle Settings’ by pressing the MENU button (4) on the screen.

4. Press the POWER button to toggle the climate controls on or off.

5. Press to toggle Automatic Air Conditioning on or off (indicated by the orange icon).

6. Press to turn on the Air Recirculation feature. When on, air will be recirculated inside the vehicle to quickly cool the interior and prevent outside air or odors from entering.
   Note: Operating this function when the A/Cis off in­creases humidity and may cause the windows to fog. This feature is not available when Defrost or Defog modes are active.

7. Activates maximum cooling with temperature automatically adjusted to the lowest setting and fan speed increased to the highest setting. Press the button again to return to the previously selected fan speed and temperature setting.

8. A preset/favorite temperature for the driver zone can be stored using the MyTemp function. Once a desired temperature for the driver has been set, long press/hold the MyTemp button until a beep is heard. A short press of the MyTemp button will now instantly restore the preset driver temperature.

9. Press to direct air at the front windscreen to help clear fog or moisture. A light will illuminate the button to indicate the active/inactive status of the Defrost mode.
   Note: For best results, clear the windows of snow or ice before activating Defrost mode. Do not attempt to operate the vehicle until windows are clear.

10. Press to defog the rear window. A light will illumi­nate in the button to indicate the active/inactive status of the Defog mode. The Defog mode will also be turned off when the vehicle ignition is turned off.
    

11.  Touch the vent control mode icons to select desired vent mode. Graphics are displayed according to the selected vent and airflow pattern. Air can be
    directed through the instrument panel, floor, side, and windshield outlets as desired.

12. Select the desired temperature for the driver zone by using the two arrow buttons.

13. Select the desired temperature for the passenger zone by using the two arrow buttons.

14. Toggle ʻDual Modeʼ function to enable different temperatures to be selected for driver and passenger zones. The turnoff to lock both zones to identical temperatures.

15.  Increase fan speed using the Fan +button

16. Decrease the fan speed using the Fan -button

17. Toggle ʻAUTOʼon to engage Auto mode for all functions (Air Direction, Air Conditioning, Recirculation, Fan Speed). Whilst in Auto Mode, the vehicle will try to reach the selected temperature in the most efficient way possible.
    Note: The ʻAUTOʼbutton will perform a different function depending on whether the climate controls are being adjusted manually, semi-automatically, or fully automatically.

If all functions are under manual control, pressing ʻAUTOʼwill activate full auto mode(all functions under automatic control). If only some functions are under manual control, then pressing ʻAUTOʼwill return all functions to manual control. A second press of ʻAUTOʼwill then activate the full auto mode.

MENU NAVIGATION

Press the MENU button to access the Configurationmenuand adjust Vehicle, ITCInterface, Language, and Version settings.
The following screenshots are sample menu displays to assist in the navigation of the user interface. Use the Return Arrow to go back to the previous menu. Press the X to close the menu window and return to the TFT color touch screen home screen. For further setting options, refer to the charts in the following pages of this manual.

  Main Menu Navigation

1. Return to the previous menu
2. Enter VehicleSettings menu
3. Enter ITCSettings menu
4. Enter Language menu
5. Enter ModuleVersionmenu
6. Header
7. Close menu settings
8. Enter Sub-menu for selected option

Sub-MenuNavigation

1. Return to the previous menu
2. Sub-menu configuration options
3. Header
4. Close menu
5. Scroll bar (Scroll Up/Down for more options)

Setting configuration options

1. Return to the previous menu
2. Setting highlighted when selected
3. Scroll bar (Use to customize setting)
4. Press to select option
5. Close menu
6. Current value (Adjust with slider)
7. Scroll bar (Scroll Up/Down for more options)

VEHICLE CONFIGURATION SETTINGS CHART

  Use the charts on the following pages of this instruction manual to navigate through the various menus and settings offered by the kit.

VEHICLE SETTINGS (INSTALLER MENU)

Toaccess the Installer Menu, quick press the Menu icon on the touch screen display four times. A popup will appear with the notification: “Installer Menu Enabled”.

*Set ‘Camera Type’to ‘Type2’ for Mustang application to enable the Zoom feature. If the Zoom feature does not work, select ‘Type1’.
**Please note that additional modules are required in order to retain the Shaker amplified system in vehicles with this OEM option.

ITC SETTINGS CHART

LANGUAGE & SOFTWARE SETTINGS CHART

NOTES

FP8419K_IG_en-GB_v1

Documents / Resources

| Aerpro Integrated Touch Screen Control Kit FP8419K [pdf] Instruction Manual
Aerpro, FP8419K, Integrated, Touch Screen, Control, Kit, for, Ford, Vehicles
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>