Aerpro CHFO17C Steering Wheel Control Interface User Manual
- May 15, 2024
- Aerpro
Table of Contents
Aerpro CHFO17C Steering Wheel Control Interface
Specifications
- Product Name: CHFO17C Steering Wheel Control Interface
- Compatibility: Select Ford vehicles, Focus 2015 onwards
- Features: Ford steering wheel control interface for vehicles with CAN-Bus
- Contents: Interface, Harness, Instruction Manual
Product Usage Instructions
Pre-Installation
Before installation, ensure you have technical knowledge, a dry
installation location away from heat sources, and the correct tools to avoid
damage.
Installation Steps
- Remove and disconnect the original head unit.
- Connect the provided 12-way Molex connector of the head unit patch lead to the interface.
- Connect the other end of the head unit patch lead to the steering wheel control input on the aftermarket head unit.
- Connect the 14-way Molex connector, car display connector, and chime retention box to the interface.
- Connect the car display connector to the vehicle and Aux Into the head unit.
- Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit.
- Connect the USB lead to the OEM USB connector and head unit.
ABOUT THIS PRODUCT
CHFO17C
Ford steering wheel control interface for Ford vehicles with CAN-Bus.
Product Contents
- Interface
- Harness
- Instruction
Application
Focus 2015>
Before installation
Read the manual before installation. Technical knowledge is necessary for
installation. The place of installation must be free of moisture and away from
heat sources. Please ensure you use the correct tools to avoid damage to the
vehicle or product.
Aerpro can not be held responsible for the installation of this product.
FITTING
-
Remove and disconnect the original head unit.
-
Connect the 12-way Molex connector of the head unit patch lead (supplied separately) to the interface.
-
Connect the opposite end of the head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit. This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
Important Note: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function
-
Connect the 14-way Molex connector, the car display connector (from the vehicle), and the chime retention box to the interface.
-
Connect the car display connector (from the interface) to the vehicle and the Aux Into the back of the head unit
-
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit.
-
Connect the USB lead to the OEM USB connector and the back of the head unit.
For aftermarket head units which do not have an ISO connector the interface uses the following wiring colours:
-
Connect the female vehicle-specific connector to the male vehicle connector. Test head unit for correct operation.
STEERING WHEEL CONTROL FUNCTIONS
To Change Time & Date
Single press Mute to switch the display on. Press & Hold Mute for 2 seconds to
enable menu mode. Press Volume +/Volume – to select ‘Clock settings’ and press
Mute to confirm. Use Volume +/Volume – to adjust the time and select the next
option with Track +/Track -. Press Mute to confirm. To set the date, repeat as
above after selecting ‘Set date’. Once the time/date has been set, press Mute
once to confirm the settings. NB. The menu option will time out after 15-20
seconds.
FAQ
- Q: What should I do if my steering wheel controls are not working after installation?
- A: Ensure that all connections are secure and correct. Double-check the wiring and consult the installation manual for troubleshooting tips.
- Q: Can I use this interface with any aftermarket head unit?
- A: The interface is compatible with most aftermarket head units. Refer to the head unit installation manual for specific instructions.
Technical Support
If you need assistance setting up or using your Aerpro product now or in the
future, call Aerpro Support Australia
TEL: 03 – 8587 8898 FAX: 03 – 8587 8866 Mon-Fri 9 am – 5 pm AEST. If you
would like to download a digital copy of this manual, or other Aerpro
manuals/software, please visit the http://aerpro.com website.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>