Aerpro CHFO19C Steering Wheel Control Interface Owner’s Manual

Aerpro CHFO19C Steering Wheel Control Interface

Product Information

Specifications

• Model: CHFO19C
• Version: V2.11/20
• Compatibility: Select Ford vehicles

Key Features
This product is a CAN-Bus Steering Wheel Control Interface designed for select Ford vehicles. It retains steering wheel controls and factory phone buttons if the vehicle is equipped.

Wiring Color Codes

• Purple – Right Rear Speaker +
• Purple/Black – Right Rear Speaker –
• Green – Left Rear Speaker +
• Green/Black – Left Rear Speaker –
• Grey – Right Front Speaker +
• Grey/Black – Right Front Speaker –
• White – Left Front Speaker +
• White/Black – Left Front Speaker –

Additional Wiring Colors

• Purple/White – Reverse Gear
• Light Green – Park Brake
• Light Pink – Speed Pulse
• Blue/White – Amplifier Turn On
• Yellow – Permanent 12V
• Black – Ground
• Red – Ignition 12V

Prior to Installation
Before installation, ensure you read the manual, have the necessary technical knowledge, and work in a suitable environment. Use correct tools to prevent damage to the vehicle or product. Aerpro is not liable for installation issues.

Fitting Guide

1. Remove and disconnect the original head unit.
2. Connect the 12-way molex connector of the head unit patch lead to the interface.
3. Connect the opposite end of the head unit patch lead to the head unit’s steering wheel control input on the back of the aftermarket head unit.
4. Connect the 14-way molex connector to the interface.
5. Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit.
6. Connect the female vehicle-specific connector/s on the harness to the male vehicle connector/s from the vehicle.
7. Test the head unit for correct operation.

Steering Wheel Control Functionality
The interface allows for retaining steering wheel control functionality in your vehicle, providing a seamless integration with aftermarket head units.

FAQ

• Q: Can I install this product in a vehicle not listed in the Vehicle Application section?
  A: This product is specifically designed for select Ford vehicles listed in the manual. Installation in other vehicles may not be compatible or supported.

• Q: What should I do if I encounter issues during installation?
  A: If you face any difficulties during installation, refer to the manual for troubleshooting steps. If problems persist, contact technical support or visit the Aerpro website for assistance.

CHFO19C
Steering Wheel Control Interface for select Ford vehicles

Vehicle Application

• Ford Edge 2007 – 2010

• Ford Escape 2008 – 2012

• Ford Expedition 2007 – 2014

• Ford Explorer 2006 – 2010

• Ford Explorer (Sport Trac) 2007 – 2010 Ford Five Hundred 2005 – 2007

• Ford Focus 2008 – 2011

• Ford Flex 2008 – 2011

• Ford Freestyle 2005 – 2007

• Ford Fusion 2006 – 2012

• Ford Mustang 2005 – 2014

• Ford Taurus 2008 – 2012

• Ford Taurus (X) 2008 – 2009

• Ford F150 (F Series Pickup) 2009 – 2012

• Ford F250 (F Series S. Duty Pickup) 2008 – 2012 Lincoln MKX 2007 – 2010

• Lincoln MKZ 2007 – 2010

• Lincoln Navigator 2007 – 2014

• Lincoln Zephyr 2006>

• Mercury Mariner 2008 – 2010

• Mercury Milan 2006 – 2010

• Mercury Montego 2005 – 2007

• Mercury Mountaineer 2006 – 2010

• Mercury Sable 2008 – 2009

Key Features

• Retains Steering Wheel Controls (if equipped)
• Retains Factory Phone Buttons (if equipped)

Designed and Engineered in the UK.
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s.

ABOUT THIS PRODUCT

CHFO19C
CAN-Bus Steering Wheel Control Interface for select Ford vehicles. Retains steering wheel controls and factory phone buttons (if vehicle is equipped).

WIRING COLOUR CODES

PRIOR TO INSTALLATION

Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid damage to the vehicle or product. Aerpro can not be held responsible for the installation of this product.

TECHNICAL SUPPORT

• If you need assistance setting up or using your Aerpro product now or in the future, call Aerpro Support Australia
• TEL: 03 – 8587 8898
• FAX: 03 – 8587 8866
• Mon-Fri 9am – 5pm AEST. If you would like to download a digital copy of this manual, or other Aerpro manuals/software, please visit the http://aerpro.com website.

FITTING GUIDE

1. Remove and disconnect the original head unit.

2. Connect the 12 way molex connector of the head unit patch lead (supplied separately) to the interface.

3. Connect the opposite end of head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit.
   NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
   Important: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function .

4.  Connect the 14 way molex connector to the interface

5. Connect the male power/speaker ISO harness to the female power/speaker ISO har-ness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to “Wiring Colour Codes” on Pg. 2.

6.  Connect the female vehicle specific connector/s on the harness to the male vehicle connector/s from the vehicle. Test head unit for correct operation.

STEERING WHEEL CONTROL FUNCTIONALITY

EXAMPLE BUTTON CONFIGURATION
(MAY DIFFER DEPENDING ON VEHICLE)

NB: INTERFACE WILL ALSO RETAIN THE VEHICLE’S FACTORY PHONE BUTTONS (IF EQUIPPED)
www.aerpro.com

References

• Home | Aerpro
• Home | Aerpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>