infineon CYBLE-343072-EVAL-M2B Airoc Bluetooth LE Module Evaluation Kit User Guide
- June 6, 2024
- infineon
Table of Contents
infineon CYBLE-343072-EVAL-M2B Airoc Bluetooth LE Module Evaluation Kit
Kit contents
- CYW9BTM2BASE1 baseboard
- CYBLE-343072-EVAL Bluetooth® radio card based on AIROCTM CYW20835 silicon (connected to the baseboard using the M.2 connector)
- USB standard-A to Micro-B cable
- Quick start guide (this document)
www.cypress.com/CYBLE-343072-EVAL-M2B
Before you start
-
Register on the Developer community and then download and install ModusToolboxTM software v2.3 (or later) with the Bluetooth® SDK at https://www.cypress.com/products/modustoolbox.
-
Do the following to download and install the
HelloSensor’ code example. This step will also install theHelloClient’ peer application required later.
a. In Eclipse IDE for ModusToolboxTM software, select File > New application. This launches the project creator.
b. In the project creator, click AIROC™ Bluetooth® BSPs.
c. Select theCYBLE-343072-EVAL-M2B’ kit and click **Next**. **d.** Click **Create** and then click **Close**. **Note:** The kit is pre-programmed with theHello Sensor’ application. -
Connect a USB cable between the PC and CYBLE-343072-EVAL-M2B (J6) to power the kit.
ModusToolboxTM software
Run the `HelloClient’ application
- Locate the
HelloClient’ peer sample application that complements theHelloSensor’ application at … _mtw23mtb_sharedwiced_btsdk toolsbtsdk-peer-apps-blerelease-v3.1.0 hellosensorWindowsHelloClient Releasex64. - Run the HelloClient executable and select the
HelloSensor’ device, which appears as a device with the nameHello’. - When prompted, allow pairing from the client to the HelloSensor device.
- In the HelloClient window, select Allow Notifications next to the Hello Input characteristic.
- Press button SW3 on the evaluation kit. Observe that the Value field shows the Hello 1 message.
- Press SW3 again, and observe that the Value field is incremented.
AIROCTM Bluetooth® LE module evaluation kit board details
CYBLE-343072-EVAL-M2B
- VDDIO current measurement jumper (J17)
- Peripheral enable jumper (J19)
- VDDIO select jumper (J7)
- Baseboard power status LED (D3)
- VBAT select jumper (J8)
- USB connector for programming/USB-UART (J6)
- VPA select jumper (J16)
- KitProg3 based on PSoCTM 5LP MCU (U12)
- KitProg3 mode select (SW5)
- KitProg3 status LED (D5)
- Debug interface select jumper (SW8)
- Debug header (J13)
- Recovery button (SW1)
- Header compatible with Arduino (J1)
- Reset button (SW2)
- Header compatible with Arduino (J2)
- User button (SW3)
- User LEDs (D1, D2)
- User LED/DMIC switch (SW4)
- Digital mic sound port (J16)
- AIROCTM CYBLE-343072-EVAL-M2B
- Analog mic footprint (MIC1)
- Thermistor (TH2)
- Thermistor enable jumper (J18)
- Header compatible with Arduino (J4)
- Bluetooth® I/O header (J12)
- Header compatible with Arduino (J3)
- Bluetooth® I/O header (J11)
- Ambient light sensor (U10)
AIROCTM Bluetooth® LE module evaluation kit pinout details
CYBLE-343072-EVAL-M2B
Please note!
THIS DOCUMENT IS FOR INFORMATION PURPOSES ONLY AND ANY INFORMATION GIVEN
HEREIN SHALL IN NO EVENT BE REGARDED AS A WARRANTY, GUARANTEE OR DESCRIPTION
OF ANY FUNCTIONALITY, CONDITIONS AND/OR QUALITY OF OUR PRODUCTS OR ANY
SUITABILITY FOR A PARTICULAR PURPOSE. WITH REGARD TO THE TECHNICAL
SPECIFICATIONS OF OUR PRODUCTS, WE KINDLY ASK YOU TO REFER TO THE RELEVANT
PRODUCT DATA SHEETS PROVIDED BY US. OUR CUSTOMERS AND THEIR TECHNICAL
DEPARTMENTS ARE REQUIRED TO EVALUATE THE SUITABILITY OF OUR PRODUCTS FOR THE
INTENDED APPLICATION.
WE RESERVE THE RIGHT TO CHANGE THIS DOCUMENT AND/OR THE INFORMATION GIVEN
HEREIN AT ANY TIME.
Additional information
For further information on technologies, our products, the application of our
products, delivery terms and conditions and/or prices, please contact your
nearest Infineon Technologies office
(www.infineon.com).
Warnings
Due to technical requirements, our products may contain dangerous substances.
For information on the types in question, please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by us in a written document signed by
authorized representatives of Infineon Technologies, our products may not be
used in any lifeendangering applications, including but not limited to
medical, nuclear, military, life-critical or any other applications where a
failure of the product or any consequences of the use thereof can result in
personal injury.
www.infineon.com
Published by Infineon Technologies AG 81726 Munich, Germany
© 2021 Infineon Technologies AG. All Rights Reserved.
Document Number: 002-34052 Rev. ** Date: 10 / 2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>