ENACFIRE B08Z7Z95JC Geek True Wireless Stereo Headphones Instructions
- June 6, 2024
- ENACFIRE
Table of Contents
TRUE WIRELESS
STEREO HEADPHONES
ENACFIRE GEEK
INSTRUCTION
Customer Support
[email protected] (US/CA)
[email protected] (UK)
We will reply to you within 24 hours and 100% solve your issues
Packaging List
Product Overview
- Charging port
- Charging case LED light
- Multifunctional button
- Earphone LED
- Earphone Mic
- Acoustic hole
- L#R logo
- Magnetic charging pin
- Speaker
Power On & Pairing
Approach 1 – With Charging Case
1. Take out earphones from the charging case 
2, Select ‘ENACFIRE Geek’ frame Bluetooth list
Approach 2 – Without Charging Case
1. Power On: Touch the earphones for 1 second.
Release when you hear the prompt sound ‘Power on! with Blue light
on.
2. Pairing: Earphones will pair automatically with Right earphone Blue and
White light flash alternately
3. Select ‘ENACFIRE Geek’ from the device’s Bluetooth list
Note : Right earphone Is the master earphone
Incoming call
Answer call / End call
Tap the Left / Right earphone once
Reject call
Touch the Left / Right earphone for 2 seconds
Music
Pause / Play
Tap the Left / Right earphone once to pause/play music in the music mode (Some
phones may require starting a media player first)
Voice Assistant
Tap the Left / Right earphone 3 times, your device’s Voice Assistant will be
activated with the ‘Beep’ prompt sound
Next song
Double-tap the Right earphone
Previous song
Double-tap the Left earphone
Adjust Volume
Touch and hold the Left earphone to decrease volume, Touch and hold the Right
earphone to Increase volume
Note:
The above functions are not supported when the earphone is used in single.
Prompt sound ‘Beep’ will be produced when the volume reaches the minimum or
maximum level.
Power Off
Mode 1
With Charging Case
Put the earphones back in the charging case, they will power off
automatically.
Note: Put only the Left earphone into the charging case, the Right
earphone will stay connected.
Put only the Right earphone into the charging case, the Left earphone will
disconnect and start pairing.
Mode 2
Without Charging Case
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for & seconds to power off both
earphones
Single Mode
| Single Mode | Earphone |
|---|---|
| With Charging Case | 1. Take out Left/ Right earphones from the charging case |
2, Select ‘—ENACFIRE Geek’ from the Bluetooth list
Without Charging Case| 1. Make sure both earphones are turned off
2. Touch the Left/ Right earphone for 1 second to turn on. Prompt sound
‘Pairing’ will be produced with Blue and White light flash alternately
3, Select ‘ENACFIRE Geek’ from the Bluetooth list
Note: There will be two ‘ENACFIRE Geek’ Bluetooth names for Left and Right earphones. Please select accordingly.
Charging
Earphones Charging Status
Earphones white LED light on Charging
Earphones white LED light off: Fully charged
Note: It takes about 1.5 hours to fully charge the earphones
Charging Case Charging Status
Lights on the charging case stand for the remaining battery capacity
Note: It takes about 1.5 – 2 hours to fully charge the charging case
Note
Please follow the below steps when both earphones fall to pair each other or
occur connection related Issues
1. Place both earphones to charging case and remain charging
2. Touch and hold the power buttons of both earphones for 8 seconds until
blue and White lights flash
3. Wait for 5 seconds, take out both earphones from the charging case
4, Delete the ‘ENACFIRE Geek’ Bluetooth name from your phone and turn off
Bluetooth
5, Turn on Bluetooth and click ‘ENACFIRE Geek’ from your phone
Safety Instruction
Using earphones at high to moderate volumes for extended perlods of time will
result in permanent hearing damage. It is advised that you keep volume levels
moderate to low at all times for your safety. Do not use them while driving,
cycling, operating machinery, or performing other activities that require
hearing surrounding sounds. Do not use earphones in thunderstorm weather, the
earphones may not work properly in bad weather conditions, and may increase
the risk of being hit by lightning. Earphones may not work properly under high
temperature or high humidity conditions, Do not use any corrosive cleaner/oil
to clean the earphones, If the earphones come in contact with liquids, quickly
wipe away. If submerged in the water, do not turn the earphones on until it is
completely dried. Tips: Man-made damage and loss are not covered under
warranty. Keep the earphones and the packaging out of reach of children.
Q &A
Q: Why does the music cut in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your
device. Please make sure there Is no Microwave oven / Wifi transmitter around
you, which is more likely to produce electromagnetic interference and result
in a signal interruption.
Note: Please keep your phone and the earphone as close as possible to ensure a
more stable Bluetooth connection.
Q: What should I do if the earphones stop charging?
A: We recommend you charge the earphones by using our cable. If our cable does
not work, please try to use another charging cable or power source to charge
the earphones.
Q: How to contact ENACFIRE Customer Service Learn?
A: If you have any issue with the product, please contact us via
s[email protected] (US/CA) /
[email protected] (UK). We will
reply to you within 24 hours and 100% solve your issue.
NOTE: This equipment has been tested and found to comply with the limits
for a Class 6 digital device, pursuant ta part 16 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is a guarantee that interference will not occur
in @ particular installation. if this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and a user is encouraged ta ‘try to correct the
interference by one or more of the following measures
— Reorient or relocate the receiving antenna.
~ Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet and a circuit different from that to
which the receiver is connected
—Consult the dealer ar an experienced radio/TV technician for help
Changes ar modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation
FCC ID: 2AV33-A305