infineon AIROC CYW20829 Bluetooth LE SoC Evaluation Kit User Guide

AIROC CYW20829 Bluetooth
LE SoC Evaluation Kit
User Guide Quick start guide
AIROC™ CYW20829 Bluetooth CYW920829M2EVK-02 ® LE SoC Evaluation Kit

AIROC CYW20829 Bluetooth LE SoC Evaluation Kit

Kit contents

1. CYW20829 Evaluation Board (CYW9BTM2BASE3+CYW920829M2IPA2)
2. USB Type-A to Micro-B cable
3. Six jumper wires (five inches each)
4. Quick start guide (this document)

www.infineon.com/CYW920829M2EVK-02

Before you start

1. Ensure that you have the following:
   • PC with USB 2.0 port
   • UART terminal software such as Tera Term or Minicom
   • Download and install the AIROC™ Bluetooth® Connect app from Play Store or iOS App Store.

2. Visit the kit website to download and install the required software.

3. Ensure the following jumper settings to select 3.3 V:
   Jumper| Position
   ---|---
   J9| 1  – 3
   J10| 1  – 3
   J12| 1  – 2

4. Connect the Kit Prog3 USB connector (J5) to your PC.
5. Wait for the driver installation to complete.
6. Open the UART terminal software and set the
   USB-UART COM port terminal setting by referring to COM port setup image.

Run the AIROC™ Bluetooth® Connect application

1. Turn ON Bluetooth® on your Android or iOS device.
2. Launch the AIROC™ Bluetooth® Connect app.
3. Press the reset switch on the CYW920829M2EVK-02  board to start sending advertisements and observe the “Advertisement started” message on the serial terminal and confirm USER LED2 blinking.
4. Swipe down on the AIROC™ Bluetooth® Connect app home screen to start scanning for LE Peripheral devices.
5.  Your device (“Find Me Target”) appears on the home screen. Tap Connect to establish a Bluetooth® LE connection with the device.
6. The USER LED2 changes from blinking state to always ON state after establishing a successful connection with the device.
7. Select ‘Find Me Profile’ and select an Alert level.
   The USER LED1 state is linked to the type of alert sent.
   • No alert: USER LED1 OFF
   • Mild alert: USER LED1 blinking
   • High alert: USER LED1 ON

1. Power LED (LED1)
2. KitProg3 USB Micro-B connector (J5)
3. KitProg3 programming mode selection button (SW3)
4. KitProg3 (PSoC™ 5LP) programmer and debugger (CY8C5868LTI – LP039, U5)
5. VBAT voltage selection jumper (J9)
6. VIO_BASE voltage selection jumper (J10)
7. VDARA voltage selection jumper (J12)
8. Analog mic (U13)
9. Power header compatible with Arduino Uno R3 (J1)
10. Reset button (SW1)
11. 10-pin MCU PROG/DEBUG header (J11)
12. Analog header compatible with Arduino (J2)
13. User Button 1 (SW2)
14. Digital mic (U11)
15. User Button 2 (SW4)| 16. User LED 1 (LED3)
17. User LED 2 (LED4)
18. M.2 stand-off (MT1)
19. AIROC™ CYW20829 Bluetooth® and Bluetooth® LE system on chip
20. M.2 E-key interface connector (J16)
21. RGB LED (LED5)
22. Thermistor (TH1)
23. Thermistor enable header (J14)
24. Peripheral enable header (J13)
25. VDDIO current measurement header (J17)
26. Six-axis IMU (U12)
27. QSPI flash memory (U14)*
28. Digital I/O headers compatible with Arduino Uno R3 (J3, J4)
29. Extended GPIO header (J18)
30. KitProg3 status LED (LED2)
---|---

*Footprint only, not populated on the board
**Component is located at the bottom side of the board

AIROC™ CYW20829 Evaluation Board pinout details

See the kit guide available at www.infineon.com/CYW920829M2EVK-02 for details.

Please note!
This Document is for information purposes only and any information given herein shall in no event be regarded as a warranty, guarantee or description of any functionality, conditions and/or quality of our products or any suitability for a  particular purpose. With regard to the technical specifications of our products, we kindly ask you to refer to the relevant product data sheets provided by us. Our customers and their technical departments are required to evaluate the  suitability of our products for the intended application.
We reserve the right to change this document and/or the information given herein at any time.

Additional information

For further information on technologies, our products, the application of our products, delivery terms and conditions and/or prices, please contact your nearest Infineon Technologies office (www.infineon.com).
Warnings
Due to technical requirements, our products may contain dangeroussubst ances. For information on the types in question, please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by us in a written document signed by authorized representatives of Infineon
Technologies, our products may not be used in any life-endangering applications, including but not limited to medical, nuclear, military life- critical or any other applications where a failure of the product or any consequences of the use  thereof can result in personal injury.

Mouser Electronics

Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Infineon:
CYW920829M2EVK-02

www.infineon.com
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2023 Infineon Technologies AG.
All Rights Reserved.
Document Number: 002-37204 Rev. *A
Date: 08 / 2023

References

• Semiconductor & System Solutions - Infineon Technologies
• CYW920829M2EVK-02 - Infineon Technologies
• Infineon Technologies Distributor | Mouser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>