GUARDO WS-200 Digital Weather Station User Guide
- June 6, 2024
- GUARDO
Table of Contents
QUICK REFERENCE GUIDE. WS-200
PARTS & BUTTONS
1. Indoor Temperature
2. Low battery indicator main unit
3. Humidity Trends
4. Indoor Humidity
5. Indoor comfort indicator
6. Time (12/24h)
7. Snooze Icon
8. Alarm Icon| 9. Weekday
10. Date
11. Comfort Indicator for different channels
12. HI/LOW Alert for Humidity
13. Humidity Data from remote sensor
14. Low battery indicator remote sensor
15. Temperature Trends
16. Temperature Data from remote sensor
---|---
- MAIN UNIT –
See illustration 1
17. Channel No. for remote sensor
18. Auto scrolling icon for measured data for different channels
19. HI/LOW Alert for Temperature
20. Snooze / Light Button
21. Hanging Hole| 22. Buttons: [SET] [CHI/▲] [▼] [ALARM] [MEM] [ALERTS] 23. Battery Compartment Cover
24. DC IN JACK
25. Metal Stands
---|---
REMOTE SENSOR –
See illustration 2
1. LED light
2. Battery compartment
3. Hanging hole| 4. Channel switch
5. Rope hanging hole
---|---
INSTALLATION
-
MAIN UNIT
1. Remove the protection foil from the display.
2. Remove the battery compartment cover (23).
3. Insert 3 x AAA batteries matching the correct polarity (+and-) (optional, for use without DC adapter).
4. Take out the metal stands in the battery compartment, assemble them into the metal stand holes (25).
5. Connect the adapter with the main unit (22) and a power outlet.
6. Close the battery compartment cover.
The main unit can be placed on a vertical surface using the metal stands (25) or it can be hung on a wall using the hanging hole (21). -
SENSOR
1. Remove the battery compartment cover, choose the channel (1,2,3) using the channel switch (4).
2. Insert 2 x AA batteries matching the correct polarity (+ and -). The red led light (1) will flash once.
3. Close the battery compartment cover.
The sensor can be hung on a wall using the hanging hole (3).
Remarks:
- Mount your sensor on a north-facing wall or in any shaded area. Under an eave or deck rail is preferred.
- The maximum wireless transmission range to the weather station is up to 50 meters in the open air, not including walls or floors.
- Mount your sensor in a horizontal position, to allow moisture to drain out properly. Keep out of direct sunlight & make sure the sensor is well-ventilated.
OPERATION
- After connecting the main unit to the power (or installing the batteries), the unit is automatically turned ON. The main unit will start to detect indoor temperature/humidity.
- To receive signals from the remote sensor, both devices should be set to the same channel. For example, if you have chosen channel 2 for the sensor, you should select channel 2 for the main unit as well. Select the desired channel for the main unit using the [CHI/▲] button at the back of the unit.
- When you have set both the weather station and the outdoor sensor to the same channel, you should keep the [CHI/▲] button pressed until you hear a beep and the 3 dashes on the display start to flash. The outdoor sensor and the weather station will now connect to each other, this can take up to 3 minutes.
BUTTONS
[SET]| Press and hold to enter Setting mode
Press to enter the following settings: language / beep / 12/24h format / time
/ date / °C/°F format
Press to confirm a setting
---|---
[CHI/▲]| Press to choose channel 1/2/3
In setting mode, press to change the setting item to the desired values
[▼]| In setting mode, press to change the setting item to the desired values
[MEM]| Press to view daily max. record/min. record / Heat Index /Dew Point
[ALARM]| Press and hold to enter Alarm time setting mode
In alarm time setting mode, press to set the alarm(s)
Press to view the 2 alarm settings
[SNOOZE/LIGHT]| Press to activate backlight for 10 seconds when powered with
batteries
Press to select the brightness level: high–soft–off when powered with an
adapter
Press to snooze an alarm. The alarm will go off again after 5 minutes. Press
any button to stop the alarm.
[ALERTS]| Press and hold to enter Alert setting mode
In alert setting mode, press to (de)activate the alarm(s)
For more detailed information about functions and settings, please check the complete and detailed manual on www.guardo.be
SAFETY INSTRUCTIONS
- The product must not be dismantled or modified in any way.
- The main unit must not be exposed to rain or moisture.
- The product is not intended to be used as a reference thermometer and we will not be held liable for any damage which may result from inaccurate readings.
- The battery should be removed if the product is not to be used for an extended period, otherwise, the battery might leak and damage the product. Never leave discharged batteries in the battery compartment.
- Changing the battery on the weather station erases the saved information.
- Do not clean any part of the product with benzene, thinner, or other solvent chemicals. When necessary, clean it with a soft cloth.
- Never immerse the product in water. This will damage the product.
- Do not subject the product to extreme force, shock, or fluctuations in temperature or humidity.
- Do not mix new and old batteries or batteries of different types.
- Do not dispose of this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.
SUPPORT
For more information, spare parts, technical questions, and return requests concerning this product, you should contact support@guardo.be.
GUARANTEE
Copyright © Guardo. Guardo is a registered trademark of TE-Group NV. The
Guardo brand stands for superior product quality and outstanding customer
service. That is why Guardo warrants this product against all defects in
material and workmanship for a period of two (2) years from the date of
original purchase of the product. The conditions of this guarantee and the
extent of responsibility of Guardo under this guarantee can be downloaded from
our website: www.guardo.be
VISIT OUR WEBSITE FOR THE DETAILED MANUAL & DOC-INFORMATIONS:
www.guardo.be
DECLARATION OF CONFORMITY
Hereby,
Company | TE-Group NV |
---|---|
Address | Kapelsestraat 61, 2950 Kapellen, Belgium |
declare that the following equipment
Product name| Guardo WS-200
Product type| Digital Weather Station
conforms with the following safety requirements of the directives 2011/65/EU, 2015/863/EU, 2014/30/EU, 2014/35/EU, 2014/53/EU, 2009/125/EU, and 2019/1782/ EU. Conformity is guaranteed by the CE symbol. This product has been tested against the following standards and specifications.
EN 62321
EN 55032:2015
EN 55035:2017
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50663:2017
EN 62479:2010| EN 62368-1:2014+A11:2017
ETSI EN 301 489-1 V2.2.1 (2019-03)
ETSI EN 301 489-3 V2.1.1 (2019-03)
ETSI EN 300 220-1 V3.1.1 (2017-02)
ETSI EN 300 220-2 V3.2.1 (2018-06)
ETSI EN 300 330 V2.1.1 (2017-02)
IEC 62368-1
---|---
J. Van Os, Product & Research Manager
Authorized Signature, Kapellen
September 2020
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>