BRAUN No Touch + Forehead Thermometer BNT400A User Manual

June 6, 2024
Braun

BRAUN No Touch + Forehead Thermometer BNT400A User Manual
BRAUN No Touch + Forehead Thermometer BNT400A

Product description

Product description

  1. Power button
  2. Scanner
  3. LCD screen
  4. Temperature button
  5. Battery door
  6. Protective scanner cap
  7. Silent mode switch
  8. Guidance light
  9. Food and bath temperature mode
  10. AgeSmartTM button

Thank you for purchasing the Braun No touch + forehead thermometer (BNT400). This thermometer is a high-quality product incorporating the latest technology and tested in accordance with international standards. With its unique technology, the product can provide a stable, accurate reading with each measurement. The thermometer performs a self-test every time it is switched on to always guarantee the accuracy of measurements. The Braun No touch + forehead thermometer is intended for the intermittent determination of human body temperature on people of all ages in a “Forehead” and “No Touch” mode, using the center of the forehead as the measurement site, in a home use environment.
Please read these instructions carefully before using this product and keep the instructions and the thermometer in a safe place.

WARNINGS AND PRECAUTIONS

Keep out of reach of children under 12 years. Never use the thermometer for purposes other than those for which it has been intended. Please follow the general safety precautions when using on children. Never immerse the thermometer into water or other liquids (not waterproof). For cleaning and disinfecting please follow the instructions in the <> section. Do not store this thermometer in temperature extremes below -25 °C or over 55 °C or in excessive humidity (above 95% non-condensing relative humidity).

If thermometer is stored in a location that is cooler or warmer than where it will be used, allow it to acclimate to the room temperature for 10 minutes before taking a measurement. Do not use the thermometer if there are signs of damage on the scanner or on the thermometer itself. If damaged, do not attempt to repair the product.

Never insert a sharp object into the scanner area or any other open surface on the thermometer. This thermometer consists of high-quality precision parts. Do not drop the instrument. Protect it from severe impact and shock. Do not twist the instrument or the measuring sensor.
This thermometer is intended for household use only.

Use of this thermometer is not intended as a substitute for consultation with your physician.
Temperature elevation may signal a serious illness, especially in neonates and infants, or in adults who are old, frail, or have a weakened immune system.
Please seek professional advice immediately when a temperature elevation occurs on persons that are:

  • Neonates and infants under 3 months (Consult your physician immediately if the temperature exceeds 37.4 °C)
  • Individuals over 60 years of age (Fever may be blunted or absent in older individuals)
  • Individuals having diabetes mellitus or a weakened immune system (e.g., HIV positive, cancer chemotherapy, chronic immunosuppressant treatment, splenectomy)
  • Individuals who are bedridden (e.g., nursing home patient, stroke, chronic illness, paraplegia, quadriplegia, surgical recovery)
  • A transplant recipient (e.g., liver, heart, lung, kidney).

This thermometer is not intended for pre-term babies or small-for gestationalage babies. Pre-term is defined as babies with a calendar age of less than 37 weeks. Small-for-gestational-age is defined as a baby born at 37 weeks or later, with a weight below the 10th percentile for babies of the same gestational age.
This thermometer is not intended to interpret hypothermic temperatures. If the device displays a temperature of 36.4 °C or less with an LED backlight color of green or white, and the individual is exhibiting atypical symptoms or behaviors, contact your physician or health care professional.
DO NOT allow children to take their temperatures unattended.
Please consult your physician if you see symptoms such as unexplained irritability, vomiting, diarrhea, dehydration, changes in appetite or activity, seizure, muscle pain, shivering, stiff neck, pain when urinating, etc., even in the absence of fever.
Even in the absence of fever, those who exhibit a normal temperature may still need to receive medical attention. People who are on antibiotics, analgesics, or antipyretics should not be assessed solely on temperature readings to determine the severity of their illness.
DO NOT modify this equipment without the authorization of the manufacturer.

Why Braun No touch + forehead?

Measurement in under 2 seconds
The innovative infrared technology allows measurement of forehead temperature in under 2 seconds whether you use the forehead or no touch option.
Measurement Timer

Accurate and reliable
Due to the unique technology, the Braun No touch + forehead thermometer captures the heat naturally given off by the foreheadto calculate body temperature value. Get the same professional accuracy whether touching your forehead or holding up to 2.5 cm away.
Accurate
Easy to use
The Braun No touch + forehead thermometer is non-invasive.
A measurement can be taken even while a child is sleeping.
The Braun No touch + forehead thermometer is safer to use on a child than a rectal thermometer and is easier to use than other methods.
Easy to use
Safe and hygienic
No touch option helps minimize spreading of germs.
Completely safe for use on children and adults.

How does Braun No touch + forehead work?

The Braun No touch + forehead thermometer measures infrared energy radiated from the skin at the center. This captured energy is collected through the lens and converted to an oral equivalent value.
The Braun No touch + forehead thermometer has been clinically tested and proven to be safe and accurate when used in accordance with its operating instruction manual.

  1. A traditional forehead product without any optical system to capture radiated heat.

AgeSmart™ color-coded display

Clinical research shows the definition of fever changes as newborns grow into infants, infants grow into children and children grow into adults.1
Select the appropriate age setting, take a temperature, and the display will glow green, yellow, or red to indicate whether the temperature is in a normal, moderate fever, or high fever range, respectively.
The device is only intended for the measurement of human body temperature. It is not intended to diagnose or monitor a serious medical condition or disease.
The device also has a food/bath mode.

  1. Herzog L., Phillips S. Addressing Concerns About Fever. Clinical Pediatrics. 2011; 50 (#5): 383-390.

Temperature taking hints

It is important to know each individual’s normal temperature when they are well.
This is the only way to accurately diagnose a fever. Take multiple readings when healthy to determine normal temperature.
A child’s normal temperature can be as high as 37.7 °C or as low as 36.1 °C.
Be sure to note this unit reads 0.5 °C lower than a rectal digital measurement.
Thermometer needs to acclimate to the room temperature for 10 minutes before taking a measurement.
The individual being measured should be indoors for 30 minutes before taking a measurement. External temperature can impact skin temperature.
If the individual is inside but in a room that is more than a few degrees warmer or cooler than the room the thermometer is in, it will impact the accuracy of the reading.
ALWAYS hold the thermometer and the forehead steady when taking a reading.
DO NOT move the thermometer until you hear the final beep. DO NOT take a measurement while or immediately after nursing a baby.
Individuals should not drink, eat, or be physically active before/while taking the measurement.
Remove hats and wait 10 minutes before taking a measurement.
Before taking a measurement, remove dirt or hair from the forehead area. Wait 10 minutes after cleaning before taking measurement.
ALWAYS take the temperature exactly as directed. Temperature results may vary if positioned in the wrong location.
For individuals measuring their own temperature, it is recommended to use the “forehead” option instead of “no touch.”

In the following situations it is recommended that three temperatures in the same location be taken and the highest one taken as the reading:

  • Newborn infants in the first 100 days.
  • Children under three years of age with a compromised immune system and for whom the presence or absence of fever is critical.
  • When the user is learning how to use the thermometer for the first time until he/she has familiarized himself/herself with the instrument and obtains consistent readings.

General precautions:

  • Remove any sweat prior to measuring with a dry cloth.
  • Avoid any cooling or warming cloths on the forehead for at least 30 minutes prior to measurement.
  • DO NOT take temperature measurements over scar tissue, open sores, or abrasions.
  • Keep the measurement sensor and lens clean. Avoid directly touching the sensor or lens.
  • ALWAYS store the thermometer with the protective cap in place to prevent dirt and scratches from damaging the device.
  • Make sure to remove the protective cap before taking a measurement and to put the cap back on after using the thermometer.

How to use your Braun No touch + forehead

Note: The thermometer and individual should be in the same ambient temperature for at least 10 minutes.

  1. Remove protective cap
    Operational Instructions

  2. Power on
    Press and release the power button once. Backlight will come on and the start- up sequence begins.
    NOTE: Make sure to remove the protective scanner cap before taking a measurement.
    Operational Instructions

  3. Select age range
    Select age with AgeSmartTM button
    Device will start cycling through the age ranges, highlighting the
    3 ranges you may select; 0-3 months ( ), 3-36 months ( ),
    or 36+ months ( ).
    Operational Instructions
    Operational Instructions
    Operational Instructions
    To set a preferred age range: (Locking an age setting)
    To save a preferred age range, so that the preferred age range will be automatically selected when the thermometer is turned ON, follow these steps:

    • Make sure the thermometer is OFF.

    • Press and hold the power button (  ) and AgeSmartTM button ( ) for 4 seconds. The unit will turn on, displaying a yellow backlight and the 3 age range icons will flash.

    • Press the AgeSmartTM ( ) button. The age range selected will flash. Press the AgeSmartTM button until your desired age range is flashing on the display.

    • Once the desired age range is selected, stop pressing the button and wait 3 seconds. The green backlight will illuminate, and the selected age range will turn solid. After 4 seconds, the thermometer will turn off.

    • The preferred age range will be automatically selected when the thermometer is turned ON.
      Note: With a preferred age range, an alternate age range can be selected during each use, by pressing the AgeSmartTM button when the age range icon appears, after the thermometer is turned ON.

    • To remove the preferred age range, open the battery door, remove the batteries, wait 30 seconds and re-insert the batteries.
      IMPORTANT: To ensure accurate readings, you must always take a temperature reading in the age range that corresponds to the individual’s age.

  4. Position
    Position thermometer on or up to 2.5 cm away from the center of the forehead, just between the eyebrows.
    When the thermometer is ready and on or 2.5 cm away from the forehead a horizontal line of dashes (“—”) will appear on the screen.
    For No touch readings, the yellow guidance light will show you where you are aiming.
    If the eyebrow area is covered with hair, sweat or dirt, please clean the area beforehand to improve the reading accuracy. It is important to hold the thermometer and the forehead steady during measurement. Movement will impact the temperature reading.
    Position

  5. Take temperature
    Three dashed lines mean the thermometer is ready to take temperature. Press the temperature button. The display will show a dashed line animation while it takes a reading. Once the reading is complete a confirmation beep will be heard and the appropriate fever light color will be displayed on screen.
    Take Temperature Take
Temperature Take
Temperature
    If the device is positioned too far away from the forehead, it will prompt you to move closer by displaying the characters “0 – 2 cm”. Slowly move the device toward the forehead until the dashed line animation starts and a reading is displayed.

  6. Read temperature
    If temperature is in the normal range, a long beep will sound when the measurement is complete. If the temperature is in the fever range, 10 short beeps will sound to indicate the measurement is complete.Read
Temperature| Read
Temperature| Read
Temperature| Read
Temperature
    ---|---|---|---

Age range

| Green Normal temperature| Yellow Moderate fever| Red High fever

*0-3 Months**

| ≥35.8 – ≤37.4 °C| |

> 37.4 °C

3-36 Months| ≥35.4 – ≤37.6 °C| > 37.6 – ≤38.5 °C|

> 38.5 °C

36 M onths – adult

| ≥35.4 – ≤37.7 °C| > 37.7 – ≤39.4 °C|

> 39.4 °C

  • 0 months is defined as having a gestational age of greater than or equal to 37 calendar weeks at birth

    1. To turn off
      Press the power button to turn off. Device will also shut off automatically after 30 seconds of no use.

How to use the Braun No touch setting to take a food/bath temperature

  1. Remove protective cap
    Remove Protective Cap

  2. Power on
    Press and release the power button once. Backlight will come on and the start- up sequence begins.
    NOTE: Make sure to remove the protective scanner cap before taking a measurement.
    Remove Protective Cap

  3. Select food & bath temperature mode
    Press and release the food & bath temperature mode button. A beep will sound, the food & bath icon ( ) will be displayed, the screen backlight will turn blue and three dashes will show on the screen indicating the thermometer is ready to take a temperature.
    Operational Instructions

  4. Position
    Position device up to 6 cm away from the bath water or food. Note: When measuring food or bath temperature the thermometer must be aimed directly at the food or bath water. DO NOT aim at sides of container holding the liquids or food. DO NOT touch liquid or food with the thermometer. Keep the sensor dry and clean. If the thermometer becomes dirty, please follow the <> section to clean.
    Position

  5. Take temperature
    Press the temperature button (you can press and hold the button or press and release it.) The display will show a dashed line animation while it takes a reading. Once the reading is complete, the display will show the temperature reading.Take Temperature

  6. Read temperature
    Remove the device and read the temperature
    Take Temperature

Changing the sound mode

The Braun No touch + forehead thermometer allows you to silence the beeps on the thermometer to avoid waking a sleeping child.
To activate the silence feature, slide the switch to the silent mode position and take a temperature reading. An icon will appear on the screen to indicate that the thermometer is in silent mode.
Changing The Sound

Calibration

The thermometer is initially calibrated at the time of manufacture. If this thermometer is used according to the use instructions, periodic re-adjustment is not required. If at any time you question the accuracy, please contact customer service.
The LOT and SN of your device are located inside the battery compartment.
Manufacturing date is given by the LOT number. The first three (3) digits represent the Julian date that the product was manufactured and the next two (2) digits represent the last two numbers of the calendar year the product was manufactured.
The last identifiers are the letters that represent the manufacturer.
An example: LOT 11614tav, this product has been manufactured on the 116th day of the year 2014.

Error message

| Situation|

Solution

---|---|---
Error Message| When 20% of battery life is left, the display flashes the low battery warning symbol; however, the device can still work until the battery life has 0% left.| Replace batteries
Error Message| If the steady battery icon is the only symbol shown on the display, the device cannot work. The battery should be replaced immediately| Replace batteries.
Error Message| This message displays when the measured temperature is lower than 34 °C or higher than 43 °C or when the room temperature is outside the operating range of 15 °C – 40 °C .| Re- measure the temperature, carefully following the instructions in <> section.
Error Message| System error – self- check display flashes continuously and will not be followed by the ready beep and the ready symbol. If error persists, If error still persists,| Wait 1 minute until the thermometer turns off automatically, then turn on again. … reset the thermometer by removing the batteries and putting them back in. … please contact customer service.
Error Message| Blank display. Thermometer does not have power.| Please check if the batteries have been loaded correctly. Also check polarity (<+> and <–>) of batteries. Contact customer service if thermometer still does not function.

Care and cleaning

Use an alcohol swab or cotton swab moistened with alcohol (70% isopropyl) to clean the thermometer casing and the measuring probe. Ensure that no liquid enters the interior of the thermometer. Never use abrasive cleaning agents, thinners or benzene for cleaning and never immerse the instrument in water or other cleaning liquids. Wait 10 minutes after cleaning before taking a temperature measurement.
Make sure to replace the protective cap after use to prevent scratches or damage from occurring to the thermometer.
Never insert a sharp object into the scanner area or any other open surface on the thermometer.

Replacing the batteries

The Braun No touch + forehead thermometer comes with 2 AAA batteries. Replace with 2 new AAA batteries when the flashing battery symbol appears on the LCD screen. To change the batteries, slide open the battery cover and remove batteries.
Replace the batteries being sure to align properly as indicated inside the battery compartment. Remove the battery from the product if it is not required for extended periods of time in order to avoid damage to the thermometer resulting from a leaking battery.
To protect the environment, dispose of empty batteries at appropriate collection sites according to national or local regulations.
Replacing The Batteries

Limited warranty

This product comes with limited warranty commencing on the date of purchase (See warranty card for details). Within the warranty period we will eliminate, free of charge, any defects in the appliance resulting from faults in materials or workmanship, by replacing the complete appliance.
This warranty is applicable only for the appliance supplied by the appointed distributor. This warranty does not cover: damage due to improper use, normal wear or use as well as defects that have a negligible effect on the value or operation of the appliance. The warranty becomes void if repairs are undertaken by unauthorized persons and if original Braun parts are not used.

Product specifications

Type

|

No touch + forehead (BNT 400)

---|---

Measuring range

|

34 °C – 43 °C

Resolution

|

0.1 °C

Laboratory accuracy

|

0.2 °C for 35 °C – 42 °C
outside that range ±0.3 °C (Ambient temperature: 15 °C – 40 °C) This thermometer displays a calculated oral equivalent estimate. Clinical accuracy characteristics and procedures are available upon request.

Display

|

Liquid crystal display, 4 digits plus special icons

Acoustic

| Audio:
Normal temp range = Green temp range: 1 long beep for 0.4 second duration Fever = Red or Yellow temp range: 10 short beeps for 0.2 second duration

Operating temperature

| 15 °C – 40 °C
Automatic switch-off|

Approx. 30 seconds after last measurement has been taken

Weight

| 100g. (with batteries), 82.5g. (w/o batteries)
Service life|

5 years

Long term storage ranges

Storage/transport temperature

| : -25 °C – 55 °C
Humidity|

15 – 95% non-condensing

Battery

| (2) AAA Batteries – at least 500 measurements
Pressure|

700-1060 hPA (0.7-1.06 atm)

This infrared thermometer meets requirements established in ASTM Standard E 1965-98 (for the thermometer system). Full responsibility for the conformance of the product to the standard is assumed by Kaz Europe Sàrl, A Helen of Troy Company, Place Chauderon 18, CH-1003 Lausanne, Switzerland
ASTM laboratory accuracy requirements for the thermometer only in the display range of 37 °C to 39 °C for infrared thermometers is ±0.2 °C, whereas for mercury-in-glass and electronic thermometers, the requirement per ASTM Standards E 667-86 and E 1112-86 is ±0.1 °C .
This device conforms to the following standards:
EN 60601-1:2014 Medical electrical equipment. General requirements for basic safety and essential performance.

ASTM E1965-98:2016 – Standard Specification for Infrared Thermometers for Intermittent Determination of Patient Temperature.
IEC 60601-1-2:2014 Medical electrical equipment – Part 1-2: General requirements for basic safety and essential performance – Collateral Standard: Electromagnetic disturbances – Requirement and tests.

NOTE: Do not use this device in the presence of electromagnetic or other interference outside the normal range specified in IEC 60601-1-2:2014.
EN 1041: 2008 Information supplied by the manufacturer of medical devices. IEC 60601-1-11:2015 Medical electrical equipment – Part 1-11: General requirements for basic safety and essential performance – Collateral standard:
Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment.

Equipment with type BF applied parts
See Instruction for use
Operating temperature
Storage temperature
Keep it dry

Internally Powered Equipment Continuous Operation
IP22: Protected against solid foreign objects of 12.5 mm diameter and greater. Protected against vertically falling water drops when the device is tilted up to 15 degrees.
MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC.
For detailed description of EMC requirements please contact customer service.
Portable and mobile RF communications equipment can affect MEDICAL ELECTRICAL EQUIPMENT.
Remove the battery from the instrument if it is not required for extended periods of time in order to avoid damage to the thermometer resulting from a leaking battery.

Please do not dispose of the product in the household waste at the end of its useful life.
To protect the environment, dispose of empty batteries at appropriate collection sites according to national or local regulations.

Guidance and manufacturer’s declaration — electromagnetic immunity


The BNT400 is intended for use in the electromagnetic environment specified below.
The customer or the user of the BNT400 should ensure that it is used in such an environment.

Phenomenon

| Basic EMC
standard or test method| IMMUNITY TEST LEVELS
HOME HEALTHCARE ENVIRONMENT
ELECTROSTATIC DISCHARGE| IEC 61000-4-2|

L 8 kV contact
2 kV, ± 4 kV, ± 8 kV, ± 15 kV air

Radiated RF EM fields a)

| IEC 61000-4-3| 10 V/m f)
80 MHz — 2,7 GHz b) 80 % AM at 1 kHz c)

Proximity fields from RF wireless
communications equipment

| IEC 61000-4-3|

See RF wireless communication equipment immunity table below

RATED power frequency magnetic fields d) e)| IEC 61000-4-8|

30 A/m g)
50 Hz or 60 Hz

  • The interface between the PATIENT physiological signal simulation, if used, and the ME EQUIPMENT or ME SYSTEM shall be located within 0,1 m of the vertical plane of the uniform field area in one orientation of the ME EQUIPMENT or ME SYSTEM.
  • ME EQUIPMENT and ME SYSTEMS that intentionally receive RF electromagnetic energy for the purpose of their operation shall be tested at the frequency of reception. Testing may be performed at other modulation frequencies identified by the RISK MANAGEMENT PROCESS. This test assesses the BASIC SAFETY and ESSENTIAL PERFORMANCE of an intentional receiver when an ambient signal is in the pass band. It is understood that the receiver might not achieve normal reception during the test.
  • Testing may be performed at other modulation frequencies identified by the RISK MANAGEMENT PROCESS.
  • Applies only to ME EQUIPMENT and ME SYSTEMS with magnetically sensitive components or circuitry.
  • During the test, the ME EQUIPMENT or ME SYSTEM may be powered at any NOMINAL input voltage, but with the same frequency as the test signal (see Table 1).
  • Before modulation is applied.
  • This test level assumes a minimum distance between the ME EQUIPMENT or ME SYSTEM and sources of power frequency magnetic field of at least 15 cm. If the RISK ANALYSIS shows that the ME EQUIPMENT or ME SYSTEM will be used closer than 15 cm to sources of power frequency magnetic field, the IMMUNITY TEST LEVEL shall be adjusted as appropriate for the minimum expected distance.

Guidance and manufacturer’s declaration — electromagnetic emissions

The BNT400 equipment is intended for use in the electromagnetic environment specified below. The customer or the user of the BNT400 should ensure that it is used in such an environment.
Emissions Test| Compliance| Electromagnetic environment — guidance
RF Emissions CISPR 11| Group 1| The ME equipment uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF Emissions CISPR 11| Class B| Complies
Harmonic emissions IEC 61000-3-2| Not Applicable| The ME equipment is solely battery powered.
Voltage fluctuations/ flicker emissions| Not Applicable
Guidance and manufacturer s declaration — RF wireless communication equipment immunity

Test frequency
(MHz)| Band a) (MHz)| Service ‘)| Modulation b)| Maximum power
(W)| Distance
(m)| Immunity test level
(V/m)
385| 380 —390| TETRA 400| Pulse modulation b)
18 Hz| 1,8| 0.3| 27
450| 430 — 470| GMRS 460, FRS 460| FM C)
-.: 5 kHz deviation
1 kHz sine| 2| 0.3| 28
710| 704 — 787| LTE Band 13, 17| Pulse modulation b)
217 Hz| 0,2| 0,3| 9
745
780
810| 800 — 960| GSM 800/900, TETRA 800. iDEN 820, CDMA 850. LTE Band 5| Pulse modulation b)
18 Hz| 2| 0.3| 28
870
930
1720| 1 700 —
1 990| GSM 1800; CDMA 1900; GSM 1900; DECT;
LTE Band 1, 3, 4, 25; UMTS| Pulse modulation b)
217 Hz| 2| 0,3| 28
1845
1970
2450| 2 400 —
2 570| Bluetooth,
WLAN,
802.11 b/g/n, RFID 2450, LTE Band 7| Pulse modulation b)
217 Hz| 2| 0,3| 28
5240| 5 100 —
5 800| WLAN 802.11 a/n| Pulse modulation b)
217 Hz| 0,2| 0,3| 9
5500
5785
a)For some services, only the uplink frequencies are included.
b)The carrie shall be modulated using a 50 0/ duty cycle square wave signal.
c) As an alte native to FM modulation, 50 % pulse modulation at 18 Hz may be used because while it does not
represent actual modulation, it would be worst case.

Certain trademarks used under license from The Procter & Gamble Company or its affiliates.

AgeSmartTM is a trademark of Helen of Troy Limited and/or its affiliates.
© 2021 All rights reserved. Made in China.

Distributed for:
Kaz Europe Sàrl
A Helen of Troy Company
Place Chauderon 18
CH-1003 Lausanne
Switzerland
www.BraunHealthcare.com
Patents: www.kaz.com/patents/braun
Printed in China
BNT400KO
PN: A002077R2
08DEC20

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals