camry CR 1113 Vintage Vinyl Record Player User Manual

CR 1113 Vintage Vinyl Record Player
User Manual

GENERAL SAFETY CONDITIONS

IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP
FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial purposes.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.

2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.

3. The applicable voltage is 230V, ~50Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.

4. Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without supervision.

5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.

6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!

7. Never leave the product connected to the power source without supervision.

8. Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc.. Never use the product in humid conditions.

9. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid
   hazardous situations.

10. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. The damaged device always turns to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.

11. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.

12. Never use the product close to combustibles.

13. Do not let the cord hang over the edge of the counter.

14. Always unplug the device after using and before cleaning.

15. Never use this device close to water, e.g.: Under the shower, in the bathtub, or above a sink filled with water.

16. If using the device in the bathroom after use remove the power plug from the socket, because water proximity presents a risk, even if the device is turned off.

17. Do not allow the device or power adaptor to wet. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put your hands in the water. Has the device been checked by a qualified electrician before using it again?

18. Do not touch the device or power adaptor with wet hands.

19. The device has to be turned off after every use.

20. In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.

21. If the device utilizes a power adaptor, do not cover it, because this can cause a dangerous temperature rise and can damage the device. Always connect the power adaptor cable to the device, and then connect the power adaptor to the power socket.

22. To save energy, if there is no audio signal from Turntable /AUX IN for a period of over 5 minutes, then the unit will automatically switch to Standby Mode.

DESCRIPTION OF THE DEVICE

1. Turntable cover
2. LCD display
3. Power diode
4. In-built speaker
5. FUNCTION button
6. SLEEP/TIMER button
7. Headphone port
8. SNOOZE button
9. MODE/CLOCK button
10. TUNER SCAN button
11. BAND button
12. TUNING DOWN button
13. TUNING UP button
14. AUX port| 15. PRESET DOWN button
16. PRESET UP button
17. ON/OFF switch/volume control
18. 45RPM disc adaptor
19. Turntable lever
20. Turntable armlock
21. Plate spin speed adjustment
22. Turntable arm
23. Turntable needle guard
24. LINE OUT jack
25. FM antenna cable
26. Power cord
27. AUTO-STOP switch
---|---

SETTING THE CLOCK
Before first use, unpack everything and remove all protective materials. Unwind the FM antenna cable and power cable. Do not cover the ventilation holes, make sure that there is a gap of a few centimeters around the radio, which is required for proper ventilation.

1. In standby mode, press and hold the MODE/CLOCK button (9) to set the 12H or 24H clock mode. ’12H/24H’ will start flashing on the display (2). Using the TUNING DOWN button (12) or TUNING UP button (13) select either the 12-hour or 24-hour mode and confirm by pressing the MODE/CLOCK button again (9). The device will enter the hour editing mode.
2. Using the TUNING DOWN button (12) or TUNING UP button (13) set the current hour and confirm by pressing the MODE/CLOCK button again (9). The device will enter the minute editing/ mode.
3. Using the TUNING DOWN button (12) or TUNING UP button (13) set the current minute and confirm by pressing the MODE/CLOCK button again (9).

SETTING THE ALARM (RADIO ALARM FUNCTION)

1. In standby mode, press and hold the SLEEP/TIMER button (6). The display will show a clock icon and ‘0:00’ will be flashing.
2. Using the TUNING DOWN button (12) or TUNING UP button (13) set the desired alarm hour and confirm by pressing the SLEEP/TIMER button (6).
3. Using the TUNING DOWN button (12) or TUNING UP button (13) set the desired alarm minute and confirm by pressing the SLEEP/TIMER button (6). The alarm time will be set.
4. The clock icon informs that the alarm is set. To turn the alarm off press the SLEEP/TIMER button (6) when the device is in standby mode. The clock icon will disappear.
5. When the alarm is activated, the device can be put into ‘snooze’ mode by pressing the ‘SNOOZE’ button (8). The device will then switch off for 10 minutes, after which the alarm will reactivate.

AUTOMATIC SHUT-OFF FUNCTION

1. When the device is switched on press the SLEEP/TIMER button (6) the appropriate number of times to select the time after which the device is to switch off (90, 80, 70…10 minutes)
2. The word ‘SLEEP’ on the display informs you that the automatic shut-off function is activated.
3. After the selected time has elapsed the device will turn off and enter standby mode.

FUNCTION BUTTON (5)
Used to change the operating mode of the device
– PHON (turntable operation mode)
– AUX (external device operation mode)
– TUNE (AM/FM radio mode)

LISTENING TO THE RADIO

1. Turn the device on using the ON/OFF button (17) and set the radio mode using the FUNCTION button (5).

2. Using the BAND button (11) set the wavelength to AM or FM.

3. Using the TUNING DOWN button (12) or TUNING UP button (13) tune to the desired radiofrequency. Pressing and holding the button for approximately 2 seconds will automatically search for the closest frequency. After it is found the search will stop.

4. To save the radio station frequency to memory press the MODE/CLOCK button (9). The program number will begin flashing.

5. Using the PRESET DOWN button (15) or PRESET UP button (16) select the program number in which you want to save the radio station.

6. Confirm the selected program number by pressing the MODE/CLOCK button (9) again. The program number will stop flashing.

7. Repeat steps 4-7 to program selected stations (maximum of 30 programs).

8. You can switch between saved programs by using the PRESET DOWN button (15) and the PRESET UP button (16).

9. You can set the volume by turning the volume control knob (17).

10. The FM antenna (24) is located on the back panel. If the reception is poor, try to move the antenna and find a spot in which the signal is strongest.
    The AM antenna is located inside the radio receiver. If the reception is poor, try moving the receiver to a different place or turning it in another direction to catch the strongest signal.

11. The TUNER SCAN button (10) is used to automatically find and save available radio stations.

PLAYBACK OF VINYL DISCS

Prior to the first use of the turntable, remove the turntable needle guard (23) and untie the knot protecting the turntable arm found next to the turntable arm lock (20).

1. Release the turntable arm lock (20) and set the device to the PHON mode.
2. Place the disc on the turntable plate. If necessary, use the adapter (18).
3. Select the plate’s rotational speed (the rotational speed depending on the type of disc) by using the switch (21).
4. Lift the turntable arm by using the lever (19). Gently slide the arm onto the track you want to listen to. Lower the needle arm using the lever (19).
5. To stop playback of the disc, lift the turntable arm using the lever (19).
6. After completion of playback of the disc lift the turntable arm using the turntable lever (19). Move the arm over the lock (20) and lower it using the lever (19).
7. To turn the AUTO-STOP function on or off using the AUTO-STOP switch (27).

CLEANING AND MAINTENANCE

1. Disconnect the radio from the network.
2. The device may only be wiped with a dry cloth.
3. The device should be kept in a dry room.

CAUTION: Do not use water for cleaning – this may damage the device.

TECHNICAL DATA

Power source: 230V ~50Hz
RMS output power: 2x 1.5W
Power: 15W
Hereby, Adler Sp. z o.o., Ordona 2a, 01-237 Warsaw, Poland declares that the radio equipment type Turntable CR1113 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:http://www.camryhome.eu/red/cr_1113.pdf

www.camryhome.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>