camry CR 4011 Oil Press User Manual

camry CR 4011 Oil Press

GENERAL SAFETY CONDITIONS. IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

1. Before using the device, read the operating manual and follow the instructions contained therein. The manufacturer is not liable for any damages caused by the use of the device contrary to its intended use or improper operation.
2. The appliance is intended for domestic use only. Do not use for other purposes not in accordance with its intended purpose.
3. The device must only be connected to an earthed socket 220-240 V ~ 50 Hz . In order to increase the safety of use, many electrical devices should not be connected to one electric circuit simultaneously.
4. Be especially careful when using the device when children are in the vicinity. Do not allow children to play with the device and do not let children or people unfamiliar with the device use it.
5. WARNING : This equipment may be used by children over 8 years of age and people with reduced physical, sensory or mental capabilities, or people with no experience or knowledge of the equipment, if this is done under the supervision of a person responsible for their safety or has been provided to them. instructions on the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and user maintenance should not be performed by children, unless they are over 8 years old and these activities are performed under supervision.
6. Always remove the plug from the outlet after use, holding the outlet with your hand. DO NOT pull on the cord.
7. Do not immerse the cable, plug and the entire device in water or any other liquid. Do not expose the device to weather conditions (rain, sun, etc.) or use it in high humidity conditions (bathrooms, damp mobile homes).
8. Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair shop in order to avoid a hazard.
9. Do not use the appliance with a damaged power cord, or if it has been dropped or damaged in any way, or if it is not working properly. Do not repair the device yourself as there is a risk of electric shock. Take the damaged device to an appropriate service center for inspection or repair. Any repairs may only be performed by authorized service points. Incorrectly performed repairs can pose a serious threat to the user.
10. Place the device on a cool, stable, even surface, away from any kitchen appliances that heat up, such as: electric cooker, gas burner, etc.
11. Do not use the device near flammable materials.
12. The power cord must not hang over the edge of the table or touch hot surfaces.
13. Do not leave the device or the power supply in the socket unattended when it is switched on.
14. For additional protection, it is advisable to install a residual current device (RCD) in the electrical circuit with a rated residual current not exceeding 30 mA . A specialist electrician should be consulted in this regard.
15. Before turning on the device, make sure that all parts are properly installed.
16. Use only accessories provided by the manufacturer.
17. Be careful not to overload the machine , do not exceed the top edge of the grain hopper (1) .
18. Always disconnect the device from the mains and disconnect the power cord from the device when it is not in use or you want to start cleaning it.
19. Do not disassemble the juicer while it is connected to a power socket.
20. Do not use abrasive pads or aggressive cleaning agents for cleaning.
21. After use and the device heater has cooled down, it is recommended to disassemble and wash the elements thoroughly.
22. The device includes a heating element to facilitate drainage of the oil and to obtain more of it. After finishing work, wait approx. 20 minutes for the heater to cool down and only after that time you can dismantle it, clean it from seed residues and wash the device.
23. The maximum operating time of the device is 45 minutes. After this time, the device turns off to protect the engine from overheating and damage. Wait 20 minutes before restarting the device.
24. The device is used for extracting oil from oilplants : nuts, seeds, seeds andgrains , the oil content of which is greater than 30% . It is forbidden to use the device with olives, olive pits , soybeans , vegetables , fand ruits, mushrooms .

Device Description

1. Hopper

2. Cover lid

3. Filter

4. Socket

5. Keypad

6. Hopper cover

7. Pressing chamber cover and heating unit

8. Oil Container

9. Pomace container

10. Pressing chamber buckle

11. Outside cover lid

12. Pressing shaft
    Keypad Description

13. Power Button

14. Reverse Button

15. Start / Pause button

Before first use

Please note that before use you should take out all of the pieces out of the box and clean the device with a damp cloth and soap water. Then please dry the device with a dry paper towel and let dry. This will make sure that there is no residue factory grease and other pieces of after production dirt from the device.
WARNING : All accessory parts are NOT SUITABLE FOR CLEANING IN THE DISHWASHER.

PLEASE NOTE:

• The device should be assembled in the package.
• You will have 2 pressing shafts in the package.
• The pressing shaft with the RED O ring is used for smaller nuts and grains.
• The pressing shaft with the BLACK O ring is used for bigger nuts and grains.

To exchange the pressing shaft:

• Take out the EMPTY hopper (1) by pulling on it upwards. It should slide out without any problems. As shown on Picture H
  NOTE : Please make sure it is empty since the contents of the hopper will spill out.

• Push the Pressing chamber buckle to the unlocked position as shown on picture I The upper part of the picture is the unlocked position and the lower is the closed position.

• Push the Pressing chamber cover and heating unit (7) as shown on picture

• Take the heat resistant glove from the set or any heat resistant oven glove.

• Remove the pressing chamber (13) as shown on picture K

• Pull out the pressing shaft and replace it with the desired one.

• Push the Pressing chamber (13) back into place and slide the pressing chamber buckle (10) into the locked position.

• Close the Pressing chamber cover and heating unit (7) down into the closed position.

• Put the hopper (1) into the proper starting position making sure it is a tight fit.

Device Use:
To use the device please make sure you have the proper pressing shaft installed. To do so please use the instructions mentioned before this chapter. After making sure the proper pressing shaft is installed follow the below instructions:

1. Open the Cover lid (2) as shown on picture E on
   Fill the hopper (1) with the desired grain or nuts as shown on picture F on
   NOTE : The raw material to be processed must not be larger than peanuts or hazelnuts. If necessary, crush them to ensure optimum processing.

2. Close the hopper (1) with the Cover lid (2) making sure it is in the proper position and the seal is tight or the device will not turn on. The protrusion on the lid needs to be inserted in the proper holes in the hopper.

3. Put the oil strainer onto the oil container (8) to make sure no additional material from the oil pressing process gets into the oil as shown on picture G on page 3. Put the oil container under the pressing shaft making sure the oil goes into the container.

4. Put the Pomace container (9) under the pressing shaft so the pomace will fall only into the container.

5. Plug the device into the mains power using the power cable from the set.

6. Turn on the device by pressing the Power Button (14). It will light up.

7. Press the Start / Pause button (16).

8. The Power Button (14) will start to blink and show the device is warming up.

9. After warming up the device will start.

10. When the hopper (1) is empty and the Pressing chamber is also empty the device will stop.

Please note that after working for 45 minutes or the hopper being empty for more than 1 minute. The device will stop.
Please note than if the seed or nut is too big or gets stuck the device will stop. Please then turn the device off and mix the seeds or nuts in the hopper with an wooden spatula.

NEVER PUT YOUR HAND INTO THE HOPPER IF THE DEVICE IS POWERED.

If the device does not start please press the REVERSE (15) button for a few seconds. Then press the Start / Pause button again and check if the device is working again.

WARNING : The appliance motor will stop after a short while after pressing the Stop button. It is to ensure the device from clogging. Please wait for the motor to stop. Then open the lid of seed container.
NOTE : The device is not designed for pressing SOYA BEANS OR OLIVES.
TIP : Start processing with a small amount to test the quality and the moisture content.

Special notes:

1. Peanut oil: To ensure the device is not getting stuffed and the engine does not stop. Please fry the peanuts dry before pressing. The size, hardness and quality are different in each batch.
2. Please make sure to use the highest quality nuts and seeds.
3. Please make sure to choose 90% dryness material. We suggest frying the materials with low temperatures for half an hour or put out into the sun for one hour.
4. Please press only as much oil as you need per day. The health benefits of freshly pressed oils are the best and if not stored correctly will dissipate fast.

Guide to the control panel lights:

• Status of the light = Machine status
• Quick flashing red light = Pre Heating
• Constant red light = Powered on but the start not pressed
• Slow flashing red light = Paused
• Greenlight = Working
• Quick flashing green light = Reverse gear

Flashing green and red light with noise = Machine not working correctly. Please check if the assembly is correct and if nothing is blocking the oil press. If the machine is assembled and not blocked please contact the seller or warranty service for support.

Technical details:

• Voltage: 220-240 V ~ 50/60 Hz
• Power : 650 W

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit
its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>