SYNCO G2 (A1) Ultracompact Digital Wireless Microphone System User Manual

Thank you for choosing SYNCO product.
Please read this manual carefully before use and Mow all instructions
mentioned herein.

Caring For Your SYNCO Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping, the impact of external force.
• Do not attempt to disassemble the product. Doing so voids the warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions happen.
• Failure to follow all the instructions may result in mechanic damage.
• Warranty does not apply to human errors.

Package List

Product Instruction

TX Transmitter

1.  External Mic Input
2. USB-C Port
3. Power(MUTE)
4. Reset(Help with Eject Pin)
5. Low Cut
6. Pairing
7. Built-in Mic
8. Display Screen
9. Pocket Clip

1. USB-C Port
2. Power (MUTE)
3. Reset(Help with Eject Pin)
4. Gain Control
5. Pairing
6. 3.5mm Audio Output
7. 3.5mm Monitoring Jack
8. Display Screen
9. Pocket Clip

Display Screen

Operations

TX

1. Power/Mute
   Long Press 2s: turn on/off the system Short Press: mute/unmute the microphone

2. Charging
   5V/2A; with USB-C Charging Cable Please fully charge the product before use.

3. External Mic Input
   TRS Mic Only
   (Note: When using an external mic, please insert it into the mic input properly.)

4. Mic Windshield & Device Installation
   

5. Reset
   

6. Low Cut
   

7. Pairing
   

The system will pair automatically after the power is on. Manual pairing: long-press the pairing button on the RX and TX for 3 seconds at the same time
RX

1. **Power/ Mute
   Long Press 2s: turn on/off the system Short Press: mute/unmute the microphone

**

2. Charging
   

3. **Reset

**

4. Gain Control
   
   

5. Pairing
   The system will pair automatically after the power is on. Manual pairing: long-press the pairing button on the RX and TX for 3 seconds at the same time
   

6. Audio Monitoring ‘A Output Connection
   

Setting The Recording Level Correctly

Camera devices generally have poor-quality, noisy preamps. In order to get the cleanest signals possible, it is highly recommended that you set the recording level on your camera quite low, 1/2 or 1/3 of it. G2 provides variable gain control, allowing you to tailor your levels to just about the environment and recording device.
Adjust the recording level of inbuilt mics for SONY Camera (Take A7S II for example)

**

Adjust the recording level of inbuilt mics for Panasonic Camera (Take LUMIX GH5 for example)
Specifications
**

TX Transmitter

Power Requirements

| 3.3V-4.7V
Battery Type| Built-in Lithium Battery, 500mAh
Battery Charging Time| 1.5H
Battery Life| 8H
Display| TFT Screen
Dimensions| 52 x 42 X 17mm
Material| Plastic
Weight| 39g

RX Receiver

Microphone
Form Factor| Built-in/External Mic
Sound Field| Mono
Polar Pattern| Omnidirectional
Frequency Range| 50Hz-20KHz
Sensitivity| -40dB (±3 dB, re 1V/Pa at 1KHz)
Maximum SPL| 135dB SPL (at 1KHz)

Warranty

Warranty Period

Thank you for purchasing SYNCO products.

1. Customers are entitled to free replacement or repair service in case of the quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYNCO products are entitled to a 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.
   Within the warranty period, if a product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

• Faults resulted from inappropriate use of a product without following its operation specification
• Artificial damage, e.g. crash, squeeze, scratch, or soaking
• Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration
• The code on the product is inconsistent with that of the warranty certificate, or the code on the product or warranty certificate is altered or torn off
• All consumable accessories attached to a product, like a cable, wind muff, battery
• Faults as a result of force Majeure re, such as fire, flood, lightning, etc.

Warranty Claim Procedure

• If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at support@syncoaudio.com.
• Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents are missing, only sales return or chargeable service will be provided.
• If the SYNCO product is out of warranty coverage, the service and the cost of the parts will be charged.

WARRANTY CERTIFICATE

Please register your warranty. Meanwhile, you are welcome to contact us via Email: support@syncoaudio.com
USER INFORMATION| Customer Name:
Phone Number:
Email:
Address:
SALES INFORMATION| Sales Date:
Model:
Product Code:
Dealer:
REPAIR RECORD| Service Date:
Technician:
Issue:
RESULT| Solved| Unsolved| Returned(Replaced)

Guangzhou Zhiving Technology Co., Ltd

| Block 15th, No.200 Fa ngcu n Avenue East, Liwan District, Guangzhou, China, 510000
---|---
support@syncoaudio.com
www.syncoaudio.com
https://www.facebook.com/syncomicrophones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>