camry CR 4220 Hand Mixer User Manual
- June 6, 2024
- camry
Table of Contents
CR 4220
SAFETY CONDITIONS. IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V, ~50Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device to use it without
supervision. -
WARNING : This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or
knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the
dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision. -
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
Never put the power cable, the plug or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid
hazardous situations. -
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let the cord hang over the edge of the counter.
-
For additional protection, it is advisable to install a residual current device (RCD) with a rated residual current in the electrical circuit.
-
Do not immerse the motor unit in water. Do not wash in dishwashers.
-
Before cleaning and removing accessories set the speed control to OFF position and unplug the power cable.
-
Before operating the device check if all parts and accessories are properly mounted.
-
During the mixing of hot products exercise extreme caution to avoid burning.
-
The device has been designed to prepare small amounts of food products. The device is not intended for industrial food processing.
-
Do not use different types of accessories (e.g. for mixing and whipping) at the same time.
-
The maximum time of continuous operation is 5 minutes. After you operate the device for 5 minutes switch it off and allow to cool.
DESCRIPTION OF THE DEVICE (fig 1 and 2)
- The “Eject” button used to release the attachments
- Speed control
- “Turbo” button
- Whipping attachments
- Mixing attachments
- Mixer body
DEVICE UTILIZATION
- Make sure that the device is disconnected from the power.
- Insert attachments into holes at the bottom of the device. Whipping attachments can be inserted parallel, and the mixing attachments should be inserted so that the attachment with disc should be placed in bigger hole (fig. 2 and 3).
- Make sure the attachments are inserted properly.
- Connect the mixer to power, insert whipping or mixing attachments. Start the mixer by switching the speed control (2) to the appropriate mixing speed.
- After the user set the speed control (2) to “0”, and unplug the mixer from the electric power.
- Press the “Eject” button to remove mixer attachments (1).
CLEANING AND MAINTENANCE
- Unplug the device from the power before cleaning it.
- Remove the accessories before cleaning them in water with washing-up liquid. Do not wash in dishwashers.
- Wipe the external parts with kitchen towel or soft cloth.
- Do not use abrasive materials to clean the device.
- Don’t immerse in water or other liquids.
TECHNICAL DATA
Power supply: 220-240V~50Hz
Power: 300W
Power Max: 750W
The device is made in class II of insulation. The device is compliant with EU
directives:
– Low voltage directive (LVD)
– Electromagnetic compatibility (EMC)
Device marked CE mark on the rating label
To protect your environment: please separate carton boxes and plastic bags and
dispose of them in corresponding waste bins. The used appliance should be
delivered to the dedicated collecting points due to hazarsous components,
which may affect the environment. Do not dispose of this appliance in the
common waste bin.