BRAYER BR1706 Juicer Instruction Manual

: October 27, 2023
: BRAYER

Table of Contents

BRAYER BR1706 Juicer
DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
BEFORE THE FIRST USE
CLEANING AND CARE
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAYER BR1706 Juicer

BRAYER-BR1706-Juicer-PRODUCT

Use the auger juice extractor to make fresh juice from fruits or vegetables. The auger juice extractors are also called «slow juicers», they press rather than crush fruits or vegetables like centrifugal ones, so with the auger juice extractors cold-pressed juice is obtained. This juice extraction technology makes cell structure, microelements, enzymes and vitamins surely preserved in juice.

DESCRIPTION

Feeding chute
Filter element
Auger
Juice collector
Juice spout
Power/reverse switch «l/0/R»
Juice cup
Pulp container
Pusher
Cleaning brush

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation manual carefully before using the press Juicer; after reading, keep it for future reference.

ATTENTION! Do not operate the Juicer for more than 20 minutes at a time. Please wait a minimum of 10 minutes before operating the Juicer again.

Use the press Juicer for its intended purpose only, as specified in this manual.
Mishandling the Juicer can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
Do not connect the unit to external timers or remotely controlled mains sockets.
Install and use the press Juicer on a flat, dry, steady surface with free access to the mains socket.
Do not use the unit outdoors.
It is recommended not to use the unit during lightning storms.
Protect the Juicer from impacts, falling, vibrations and other mechanical stress.
Never leave the unit connected to the mains unattended.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the Juicer in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
Do not use the Juicer in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
If the Juicer is dropped into water, unplug it immediately, and only then you can take the unit out of water. Contact a service center to check or repair the unit.
Do not let the power cord touch hot surfaces and sharp edges of furniture.
Use only the removable parts supplied with the press Juicer.
Always check the filter element for mechanical damage, if you find any, do not use the juice extractor until you replace the filter element.
Do not use your fingers or any utensil other than the included plunger while inserting fruits and vegetables into the feeding chute.
Do not disassemble the Juicer if the device is plugged into the mains.
Unplug the unit after usage or before cleaning. When unplugging the Juicer, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
Do not touch the unit body, the power cord and the power plug with wet hands.
For child safety reasons do not leave polyethylene bags used as packaging unattended.
ATTENTION! Do not allow children to play with polyethylene bags or packaging film. The danger of suffocation!
The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during the operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or bypersons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the authorized service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After unit transportation or storage at negative temperature, unpack it and wait for 3 hours before using.

Unpack the unit and remove all the packaging materials.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When the unit is used in the mains with 60 Hz frequency, it does not need any additional settings.
Disassemble the Juicer and wash the parts that come into contact with fruit and vegetables when the Juicer is in use.
Remove the pusher (9) from the feeding chute (1).
Turn the feeding chute (1) with the filter element (2) counterclockwise until the «▲» mark matches the « » mark on the top of the motor unit and remove them (Fig. 1).
Remove the juice collector (4) from the motor unit upwards (fig. 2).
Remove the auger (3) from the juice collector (4) (fig. 3).
Wash the removed parts (1-2, 3, 4, 9), the juice cup (7), the pulp container (8) and the cleaning brush (10) with warm water and a neutral detergent, then rinse and dry.
Wipe the motor unit with a slightly damp cloth, then dry it.

JUICE EXTRACTOR ASSEMBLING

Place the juice extractor on an even, dry and stable surface so that an electrical outlet is always easily accessible.
Make sure before assembling the juice extractor that the silicone seal on the underside of the juice collector (4) is in place (fig. 4).
Notes: the silicone seal must fit tightly into its place of installation, otherwise the juice may flow out of the juice collector (4) during the operation and damage the juice extractor.
Install the juice collector (4) on the motor unit (fig. 5).
Install the auger (3) into the juice collector (4), make sure that the auger (3) is correctly installed, it must be mounted on the driving shaft and sink slightly intothe juice collector (4), otherwise, the installation of the filling chute (1) with the filter element (2) will not be possible.
Install the feeding chute (1) with the filter element (2) on the juice collector (4), the «▲» mark must match the « » mark on the top of the motor unit, turn the feeding chute (1) with the filter element (2) clockwise to « » (Fig. 7). Make sure the feeding chute (1) with the filter element (2) are securely fixed.
Insert the pusher (9) into the feeding chute (1).
Place the juice cup (7) under the spout (5) and install the pulp container (8) (fig. 8).
The juice exractor is ready for use.

TIPS

The Juicer is not intended for extracting juice from fruits, containing high levels of
pectin or starch, such as bananas, papayas, figs, avocados, and etc., bananas contain little to no juice, only add them for the scent.
The Juicer is not intended to process too hard highfiber foods, such as, coconuts, quinces, rheum, and etc.
Use other types of kitchen appliances to process those kinds of food.
Only use ripe fruit and fresh vegetables, as they contain most juice.
Various fruits (apples, grapes, pineapples, and etc.) and vegetables (carrots, beetroot, celery stalks, spinach, cucumbers, tomatoes, and etc.).
Wash and dry fruit and vegetables thoroughly before extracting juice from them.
Berries are quick to lose their freshness, wash them immediately before juicing.
Removing only the thicker skins of such ingredients as, for example, pineapples. Removing the thinner ones is not necessary.
Choose the apple cultivar according to your needs; remember that the richness of the juice will depend on the cultivar.
It is desirable to remove cores while pressing apple juice, otherwise the normal juice extractor operation may get affected.
Apple juice quickly darkens, to slower this process add a few drops of lemon juice.
Drink juice immediately following its extraction; if left in open air, it will lose its taste and nutritional value.
If you are planning to store the juice, pour it into an airtight container and keep in a refrigerator.
Do not store the juice in metal containers – it can acquire metal taste.

MAKING JUICE

ATTENTION!

Do not operate the Juicer for more than 20 minute at a time. Please wait a minimum of 10 minute before operating the Juicer again.
Always check the grate filter element (2) for damages before assembling the Juicer.
Do not use the Juicer if the grate filter element (2) is damaged.
Prepare fruits or vegetables, wash them thoroughly, remove inedible parts from fruits such as stems, peel pineapple hard shell, remove cherry or peach pits, cut fruits or vegetables into max. 5×2 cm strips or 3×3 cm pieces
Make sure the juice extractor is correctly assembled, see the paragraph «juice extractor assembling».
Open the lid of the juice spout (5) (fig. 9).
Connect the power plug to an electrical outlet.
Switch the juice extractor on by setting the switch (6) to the «l» position.
Put fruits or vegetables into the feeding chute (2 1) only while the auger (3) is rotating and slightly press them with the pusher (1 9).
Only put fruit and vegetables into the feeding chute (9), when the grate auger (4) is rotating, while lightly pushing them through with the plunger (9). Avoid applying excessive force when pushing the plunger (9).
Do not use your fingers or any utensil other than the included plunger (9) while inserting fruits and vegetables into the feeding chute (1).
Regularly check the filter element (2) for clogging with the pulp, if necessary switch the juice extractor off by setting the power switch (6) to the «0» position, and disconnect the power plug from the electrical outlet.
Turn the feeding chute (1) with the filter element (2) counterclockwise until the «▲» mark matches the « » mark on the top of the motor unit and remove them (Fig. 1), rinse the filter element (2) under running water and install it back by turning the feeding chute (1) with the filter element (2) clockwise to « » (Fig. 7). Make sure the feeding chute (1) with the filter element (2) are securely fixed, insert the power cord plug into an electrical outlet, switch the juice extractor on to continue the operation.
To mix different juices while the juice extractor is running you can close the juice spout (5) lid (fig. 9) and continue pressing juice from another fruit or vegetable, then open the spout (5) lid and pour the juice into the cup (7).
Close the spout (5) lid when pouring the juice from the cup (7) or when the juice extractor operation is finished.
If the auger (3) slows down during the juice extractor operation, immediately switch the juice extractor off by setting the power switch (6) to the «0» position, after the auger (3) stops rotating, move the power switch (6) to the «R» position and hold it, the auger (3) reverse rotation function will be activated. After a few seconds release the power switch (6), disconnect the power cord plug from the electrical outlet, turn the feeding chute (1) with the filter element (2) counterclockwise until the «▲» mark matches the « » mark on the top of the motor unit, and remove them (fig. 1), eliminate the cause of the auger (3) slow rotation. Having eliminated the cause, install the feeding chute (1) with the filter element (2) and continue using the juice extractor.
Once the juice container (7) has filled up, turn the Juicer off and pour the juice into a suitable container, place the juice container (7) under the juice spout (5).
Keep the juice container (8) full, turn off the juicer and remove the juice from the container (8).
Note: for your convenience, place an appropriately sized bag into the pulp container (10) to remove the pulp together with the bag.
Once you finish using the Juicer, turn it off by setting the power (6) to «0», and unplug it from the mains.

OVERHEATING PROTECTION

Exceeding the operating temperature will trigger the overheating protection and the Juicer will turn off.
Should the Juicer turn off on its own, set the power (6) to «0» and unplug it from the mains.
Depending on the room temperature, the electric motor can take from 20 to 50 minutes to cool down, once it has cooled down, plug it into the mains and turn the Juicer on.
Should the Juicer fail to turn on, wait for some time, if nothing changes this might indicate another defect. In this case, please, contact an authorized service center.
Do not exceed the recommended operation time.

CLEANING AND CARE

Perform cleaning of the Juicer after each use.
Turn off the Juicer and unplug it from the mains before cleaning.
Remove the pusher (9) from the feeding chute (1).
Turn the feeding chute (1) with the filter element (2) counterclockwise until the «▲» mark matches the «» mark on the top of the motor unit and remove them (Fig. 1).
Remove the juice collector (4) from the motor unit upwards (fig. 2).
Remove the auger (3) from the juice collector (4) (fig. 3).
Remove the silicone seal on the bottom of the juice collector (4) (fig. 10).
Remove the seal ring from the central part of the juice collector by pressing it and pushing it inside the juice collector (4) (fig. 11).
Wash the removed parts (1-2, 3, 4, 9), the juice cup (7), the pulp container (8), and the seal ring with warm water and a neutral detergent, then rinse and dry.
Install the silicone seal on the bottom of the juice collector (4) (fig. 4).
Place the seal ring back to its place so that one seal rib remains outside the juice collector (4) (fig. 13) and the other ones are inside the juice collector (4).
Use the brush (10) to clean the filter element (2) and other hard-to-reach places.
Do not wash the removable parts of the Juicer in a dishwasher.
Clean the motor unit with a slightly damp tissue, then wipe it dry.
Do not use metal scouring pads, abrasives, or solvents for cleaning the Juicer.
Fruits and vegetables with painting properties, blackberries, carrots, or beetroot, for example, can color certain parts of the Juicer. If this happens you can try clearing the paint with a dry tissue soaked in vegetable oil, followed by washing the parts with warm water and a neutral detergent, rinsing, and drying them.

STORAGE

Perform a cleaning of the Juicer before taking it away for storage.
Keep the Juicer in a dry cool place unreachable by children or people with disabilities.

DELIVERY SET

Juicer – 1pc.
Instruction Manual – 1pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50-60 Hz
Rated input power: 130 W
Juice container volume – 0.6 l
Pulp container volume – 0.45 l
Troubleshooting

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after the service life expiration of the unit or the batteries (if included), do not discard them with usual household waste, deliver the unit and the batteries to specialized centers for further recycling. The waste generated during the disposal of the unitis subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product. The manufacturer reserves the right to change the appearance, design, and specifications not affecting the general operating principles of the unit, without prior notice. The unit operating life is 3 years The manufacturing date is specified in the serial number. In case of any malfunctions promptly apply to the authorized service center.

Hergestellt für «Ruste GmbH»,
Berggasse 18/18, 1090 Wien,
Osterreich
Produced for «Ruste GmbH»,
Berggasse 18/18, 1090 Vienna, Austria

т.: +7 (495) 297-50-20,
e-mail: info@brayer.su