BRAYER BR4265 Vacuum Cleaner Instruction Manual

BRAYER BR4265 Vacuum Cleaner

DESCRIPTION

Wireless handheld vacuum cleaner is intended for room dry cleaning.

1. Indication/Operation Mode Selection Panel
2. Power Button
3. Handle
4. Rechargeable Battery
5. Body
6. Dust Box
7. Upper Extension Pipe/Nozzle Lock
8. Extension Pipe
9. Lower Extension Pipe/Nozzle Lock
10. Power Brush
11. Digital Charge Level Indication
12. Suction Power Mode Indication (Low-Medium-High)
13. Suction Power Setting Button
14. Charge Level Light Indicator
15. Rechargeable Battery Lock
16. Power Adapter Cable Jack Socket
17. Dust Box Lower Cover
18. Lower Cover Lock
19. Dust Box Lock
20. HEPA Filter Holder
21. HEPA Filter
22. Mesh Filter
23. Universal Nozzle
24. Power Adapter
25. Wall Mount

SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation manual carefully before using the vacuum cleaner; after reading, keep it for future reference.

• Use the unit for its intended purpose only, as it is stated in this manual.

• Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.

• Make sure that the operating voltage of the Power Adapter (as indicated on the label) corresponds to the mains voltage.

• Do not touch the power adapter body with wet hands during battery charging.

• Before using the vacuum cleaner charge the battery.

• If you didn’t use the vacuum cleaner more than for 3 months, charge the battery.

• Do not charge the rechargeable battery in places with high moisture and high temperature. Charge the accumulator battery at the temperature from +5° C to
  + 35° C and relative air humidity no more than 80%.

• Do not leave the plugged in power adapter unattended.

• Do not use the Vacuum Cleaner with the Dust Box installed improperly or with no Dust Box installed, with no Mesh Filter or HEPA Filter installed.

• Do not use the vacuum cleaner if the dust bin is not installed or installed improperly, or if the inlet and outlet filters are not installed.

• Use only the parts and attachments supplied with the unit.

• Do not use the vacuum cleaner outdoors.

• Protect the unit from impacts, falling, vibrations and other mechanical stress.

• Do not use the unit near heating appliances, heat sources or open flame.

• Do not use the vacuum cleaner in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids; do not use the vacuum cleaner in the places where such liquids are stored.

• The vacuum cleaner is not intended for collecting water or other liquids.

• Do not use the vacuum cleaner for collecting burning or smoking cigarettes or cinders.

• Do not use the vacuum cleaner for collecting dust of plaster, concrete, flour or ashes.

• Do not use the vacuum cleaner to clean your pets’ fur.

• Keep free hanging clothes, hair and other parts of
  your body away from the air inlets of the brush or the attachments while room cleaning.

• Close attention is necessary while cleaning the stair landings

• Do not cover the inlets and outlets of the vacuum cleaner with any foreign objects. Do not switch the vacuum cleaner on if any of its openings is blocked.

• Do not use the power cord as a handle for carrying the vacuum cleaner; carry it by the handle.

• Perform periodic cleaning of the Dust Box, Mesh Filter, and HEPA Filter.

• Turn off the Vacuum Cleaner, using the Power button, after use or before cleaning.

• For children safety reasons do not leave polyethylene bags used as a packaging unattended.
  Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• The unit is not intended for usage by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the power adapter body during battery charging.

• Be especially careful if children or disabled persons are near the operating unit.

• During the unit operation and breaks between operation cycles, place the unit out of reach of children.

• The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• Do not repair the unit by yourself. Do not disassemble the unit by yourself; if any malfunction is detected, and after the unit has been dropped, apply to the service center.

• To avoid damage, transport the unit in the original package.

• Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

• Unpack the vacuum cleaner, remove all packaging and advertising materials.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the unit for damages; if the unit is damaged, do not switch it on.
• Make sure the indicated Power Adapter voltage specifications correspond to the specifications of your mains. No additional setup is required when using the device with the mains operating on 60 Hz frequency.

ASSEMBLING THE VACUUM CLEANER

• Install the rechargeable battery (4) to the installation place until the lock (15) (pic.1) clicking.

Attaching the extension pipe

• Insert the extension pipe (8) into the vacuum cleaner air inlet untilthe clamp (7) clicking (pic.2).
• Connect the electric brush (10) to the extension pipe (8) (pic.3).
• To detach the extension pipe (8) from the vacuum cleaner press and hold the clamp (7).
• To detach the electric brush (10) from the extension pipe (8) press and hold the clamp (9).

Electric brush

• Use the electric brush (10) for cleaning rooms with smooth floors or carpets with medium and low pile.

Notes:

• do not use the electric brush (10) if the pile length exceeds 15 mm.
• do not run the electric brush (10) over electric wires.

UNIVERSAL NOZZLE

• The Universal Nozzle (23) is intended for cleaning radiators, crevices, and so on; as well as for dedusting furniture surfaces. The fibers on the brush prevent damage to the polished furniture surfaces. When using the Vacuum Cleaner, install the Nozzle (23) into the necessary position by pressing the Lock.
• You can attach the crevice nozzle (23) to the extension pipe (8) (pic. 4) or to the air inlet of the vacuum cleaner (pic. 5).

WALL-MOUNTED HOLDER OF THE VACUUM CLEANER

• Select the storage place for the vacuum cleaner/the battery charging. Place the wall-mounted holder (25) near the mains socket.
• Place the wall-mounted holder (25) so that the vacuum cleaner does not hang. The vacuum cleaner should rest on the electric brush (10).
• IMake sure that no electric wiring or other utilities is inside the selected wall area before drilling orifices in it.
• Unscrew the two mounting screws, plug the Power Adapter (24) jack into the Wall Mount, and reinstall the Wall Mount, screw in the mounting screws (Fig. 7).
• Fasten the wall-mounted holder (25) with dowels and fastening screws.

BATTERY CHARGING

ATTENTION!

• Use only the battery supplied with the unit. Using a non-original battery can be dangerous.
• Do not expose Li-ion batteries to impacts and high temperatures. Do not disassemble the battery to avoid the electrolyte leakage.
• Do not throw the battery into fire.
• Avoid the battery terminals circuit, it may cause burns or fire.
• Do not discard the battery with usual household waste, apply to a specialized center for further recycling.
• Before using the unit for the first time or after a long period of inactivity, charge the battery.

CHARGING THE DETACHED RECHARGEABLE BATTERY

• Plug the Power Adapter (24) jack into the Socket (16) on the Rechargeable Battery (4).
  Plug the Power Adapter (24) into the mains – the Light Indicator (14) will turn red; when the charge of the Rechargeable Battery (4) is full, the Light Indicator (14) will turn green (Fig. 6).

• Unplug the Power Adapter (24) from the mains once the Rechargeable Battery has been fully charged.

• Install the Power Adapter (24) connection cable jack into the Wall Mount (25) before securing it on the wall if you plan to always charge the Rechargeable Battery (4) from the Wall Mount (25) (See the «Wall Mount» section).

• Dock the Vacuum Cleaner into the Wall Mount (25), plug the Power Adapter (24) into the mains – the Digital Indication (11) will display the Rechargeable Battery (4) Charge Level; the « » symbol will be flashing while the Rechargeable Battery (4) is charging; the Digital Indication (11) will display the value of «100».

• Full charging of the rechargeable battery takes about 4- 5 hours.

• After charging the battery disconnect the power adapter (24) from the mains.

Notes:

• charge the battery at the temperature from +5°C to +35°C.
• if you didn’t use the vacuum cleaner for more than 2-3 months, fully charge the battery before using the vacuum cleaner.

USING THE VACUUM CLEANER

ATTENTION!

• If the suction power of the vacuum cleaner decreases rapidly while cleaning, switch it off immediately and check the extension pipe (8) for obstruction. Remove the obstruction and only then continue cleaning.
• Do not use the vacuum cleaner to collect burning or smoking cigarettes, cinders, plaster or concrete dust, flour or ashes.
• The vacuum cleaner is not intended for collecting water or other liquids.
• Do not use the vacuum cleaner in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids, do not use the vacuum cleaner in
  the places where such liquids are stored.

SWITCHING THE VACUUM CLEANER ON
Attention! Only turn on the Vacuum Cleaner with the installed Dust Box (6) with the Mesh Filter (22) and HEPA Filter (21) installed into it.

• During cleaning or when carrying the vacuum cleaner hold the unit by the handle (3).
• For easy storing of the vacuum cleaner or the battery charging use the wall-mounted holder of the vacuum cleaner (25).
• Press the Power Button (2) to turn on the Vacuum Cleaner – the Vacuum Cleaner will turn on in the Low Suction Power Mode; press the Power Button (2) again to turn the Vacuum Cleaner off.
• When using the Vacuum Cleaner, you can alternate between Suction Power Modes by pressing the Suction Power Setting Button (13); the Indication/Operation Mode Selection Panel (1) will display the Suction Power Mode (12).
• The Digital Indication (11) will display the Charge Level of the Rechargeable Battery (4).

CLEANING AND CARE

Attention!
Keep the Dust Box (6), Mesh Filter (22), and HEPA Filter (21) clean, the performance of the Vacuum Cleaner depends on it.

• For best results, clean the Dust Box (6) after each use of the Vacuum Cleaner; perform a periodic cleaning of the Mesh Filter (22) and the HEPA Filter (21).
• Press and hold down the Lock (19) to remove the Dust Box (6) (Fig. 8).
• To remove dust and garbage, position the Dust Box (6) over the garbage bin, lift up the Lock (18) (Fig. 9) and open the Cover (17) (Fig. 10), remove the dust and garbage, close the Cover (17) so that the Lock (18) activates.
• Reinstall the Dust Box (6), make sure that the Dust Box (6) has been safely secured by the Lock (19).

Cleaning the Dust Box

• Press and hold down the Lock (19) to remove the Dust Box (6) (Fig. 9).
• Remove any dust and garbage from the Dust Box (6), as indicated above, before cleaning.
• Remove the Holder (20) from the Dust Box (6), detach the Mesh Filter (22) and the HEPA-Filter (21), remove the Mesh Filter (22) form the HEPA Filter (21).
• Wash the Mesh Filter (22) and HEPA Filter (21) under a warm jet of running water and let them dry.
• Wash the dust bin flask (6) and dry.
• Do not wash all removable parts in a dishwashing machine.

Note: before assembling the dust bin (6) make sure that all removable parts are clean and dry.

Assembling of the dust bin

• Install the Mesh Filter (22) onto the HEPA Filter (21), and install them onto the Holder (20).
• Install the Holder (20) into the Dust Box (6) retort.
• Reinstall the assembled Dust Box (6) so that the Lock (19) produces a clicking sound; make sure that the Dust Box (6) is properly secured.

Cleaning the electric brush

• When using the electric brush (10) threads or long hair etc. can wind up around the rotating brush. Keep the electric brush (2) clean, disassemble the brush
  (10) and clean the round brush as it becomes dirty.

• Remove the electric brush (10) from the extension pipe (8) by pressing the release button (9).

• Using, for example, an appropriately sized coin, rotate the Lock all the way counter-clockwise (Fig. 10), remove the round brush (Fig. 12, 13) remove any thread and hair wound-up onto the round brush.

• Clean the inner and outer surface of the electric brush (10) body from garbage and dust.

Assembling the electric brush

• Insert the left part of the round brush all the way into the body of the Brush (10).
• Turn the lock clockwise until it stops (Fig 11).
• Make sure that the round brush is fixed properly.

Cleaning the vacuum cleaner body

• Wipe the vacuum cleaner body (5) with a soft, slightly damp cloth and then wipe it dry.
• Never immerse the vacuum cleaner body (5), the electric brush (10) and the power adapter (24) into water or other liquids. Make sure that no liquid gets inside the vacuum cleaner body (5) and the electric brush (10).
• Do not use solvents or abrasives for cleaning the vacuum cleaner body and the removable parts.

STORAGE

• Before taking the vacuum cleaner away for storage, clean the vacuum cleaner body (5), the dust bin (6) and the electric brush (10).
• Keep the vacuum cleaner in a dry cool place out of reach of children and disabled persons.

DISPOSING OF THE BATTERY

• Press the lock (15) and remove the rechargeable battery (4). Do not throw out the battery with usual household waste, apply to a specialized center for further recycling.

Troubles and troubleshooting

Charge the battery.
The suction power decreased.| The dust bin is full.

The HEPA-filter

is dirty.

The extension pipe became obstructed.

The round brush in the electric brush does not rotate.

The battery is almost discharged.

| Clean the dust bin.

Clean the HEPA-filter.

Remove the obstruction from the extension pipe.

Clean the electric brush.

Fully charge the battery.

The indicator does not light up when the

Rechargeable Battery is charging.

| No voltage in the electric socket.

Power Adapter is not plugged in.

The contact point of the jack with the charging socket is faulty.

| Check whether the electric socket is operational by plugging in device known to be operational.

Plug the Power Adapter into an electric socket.

| | Check the connection between the Power Adapter Cable Jack Socket and the charger.

Short operation time of the vacuum cleaner.| The battery is not fully charged.| Fully charge the battery.
---|---|---
| Natural aging process of the battery.| The rechargeable battery is a consumable material. After the warranty period expires, the consumer should buy a new battery.

DELIVERY SET

1. Vacuum cleaner (with the dust bin) – 1 pc.
2. Wall-mounted holder – 1 pc.
3. Extension pipe – 1 pc.
4. Electric brush – 1 pc.
5. Universal Nozzle – 1 pc.
6. Power adapter – 1 pc.
7. Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Vacuum cleaner:

• Rechargeable battery: 29.6 V, Li-Ion 2200 mA/h
• Rated input power: 350 W

Power adapter:

• Power supply: 100-240 V ~ 50/60 Hz
• Output voltage: 27 V 500 mA
• Dust bin capacity: 1 l.
• Operation time at low power is about 40 min.
• Operation time in the Medium Suction Power Mode – around 20 minutes.
• Operation time at maximal power is about 12 min.

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, but take the unit and the batteries to specialized stations for further recycling.
The waste generated during the recycling of the unit is subject to mandatory collection and consequent recycling in the prescribed manner.
For further information about recycling of this product, apply to the local municipal administration, a household waste recycling service or to the shop where you purchased this product.
The manufacturer reserves the right to change the appearance, design and specifications not affecting the general operation principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions, promptly apply to the authorized service center.

Hergestellt für «Ruste GmbH», Berggasse 18/18, 1090 Wien, Osterreich
Produced for «Ruste GmbH», Berggasse 18/18, 1090 Vienna, Austria
Изготовлено по заказу Русте Гмбх, Бергассе 18/18, 1090 Вена, Австрия
Уполномоченное изготовителем лицо: ООО «Грантэл»
143912, МО, г. Балашиха,
ш. Энтузиастов, вл. 1А
т.: +7 (495) 297-50-20,
e-mail: info@brayer.su
Made in China/Произведено в Китае
brayer.ru

References

• BRAYER - официальный сайт австрийского бренда бытовой техники

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>