BRAYER BR4880 Electric Convector Heater Instruction Manual

BRAYER BR4880 Electric Convector Heater

CONVECTION HEATER BR4880
A convection fan heater is intended for use as an additional heating unit, for heating of a small amenity room or its certain area.

DESCRIPTION

1. Hot air output
2. Thermostat knob
3. Power switch «0-I»
4. Feet (2 pcs.)
5. Wheels (4 pcs.)
6. Mounting brackets

ATTENTION!

• Portable convection fan heaters are intended for use as a supplementary source of heat, for heating a small amenity room or its certain area. They are not intended for use as main heating units.
• For additional protection, it is reasonable to install a residual current device (RCD) with a nominal operating current not exceeding 30 mA. To install an RCD, contact an electrical technician.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation manual carefully before using the convection fan heater; after reading this manual, keep it for future reference.

• Use the unit for its intended purpose only, as it is stated in this manual.

• Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.

• Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.

• The three-wire power cord of the convection fan heater has a ground wire, and the power plug has a ground contact. Always connect the power plug to the socket with reliable grounding contact. In case of any inner short circuit, grounding reduces the risk of electric shock, because the current will pass through the ground wire.

• To avoid fire, do not use adapters for connecting the unit to the mains.

• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

• If you use an extension cord, make sure that the wire cross-section of the extension cord and the wire cross-section of the power cord of the convection fan heater match.

• Place the convection fan heater vertically on even dry moisture- and thermal-resistant surfaces, do not place it horizontally, and do not turn it over.

• Make sure to use the feet only when placing the unit on the floor or installing the wheels in the feet.

• When using the wheels, install the convection fan heater on an even steady surface.

• When mounting the unit on the wall, make sure that the main socket is below the level of the unit body and easy to access.

• When mounting the unit on the wall, the distance from all sides of the unit body to any objects should be at least 300 mm, the main socket must be below the level of the unit body and easy to access.

• Do not place the convection fan heater on soft surfaces, such as carpets with deep piles, sofas, or beds.

• The distance between the front grid of the convection fan heater and the furniture should be at least 1 m.

• Do not use the convection fan heater in a limited space, for example, in built-in cabinets or wall niches.

• Do not use the unit if the room temperature is above + 30ºС.

• Do not use the power cord as a carrying handle.

• Do not wind the power cord around the unit body.

• Provide that the power cord does not contact with hot surfaces and sharp furniture edges.

• Protect the unit from impacts, falling, vibrations, and other mechanical stress.

• Avoid blocking the bottom air grid with foreign objects, do not cover the unit during the operation.

• Do not use the unit to dry clothes or other household items.

• Do not use the unit in places where inflammable liquids are used or aerosols are sprayed, do not use the unit in the places where such liquids are stored.

• Do not use the unit outdoors. When using the unit in the bathroom, place the unit in such a way that the distance from the nearest faucet is at least 60 cm, and in no case splashes of water should fall on the unit and inside the body of the unit.

• Do not use the unit near swimming pools or other containers filled with water.

• If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of the water. Apply to the authorized service center for testing or repairing the unit.

• Do not touch the unit body, the power cord, and the power plug with wet hands.

• It is not recommended to use the unit during lightning storms.

• During operation the convection fan heater body heats up strongly, do not touch hot parts of the unit body to avoid burns.

• Avoid getting burned by hot air.

• Never leave the unit connected to the mains unattended.

• Unplug the unit after usage or before cleaning.

• Switch the convection fan heater off and unplug the power cord plug from the main socket.

• When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage or cause a short circuit.

• Do not immerse the unit in water or any other liquids.

• If water droplets fall on the convection fan heater body, switch it off and disconnect the power plug from the mains before touching the unit, then wipe the unit body with a dry cloth.

• For child safety reasons do not leave polyethylene bags used as packaging unattended.
  ATTENTION! Do not allow children to play with polyethylene bags or packaging film. The danger of suffocation!

• The unit is not intended for usage by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the unit body, the power cord or the power plug during the operation of the unit.

• Be especially careful if children or disabled persons are near the operating unit.

• During the unit operation and breaks between operation cycles, place the unit out of reach of children.

• The unit is not intended for usage by physically, sensory, psychically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under the supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• From time to time check the power cord integrity.

• If the power cord is damaged, it should be replaced by the manufacturer, maintenance service, or similarly qualified personnel to avoid danger.

• If a foreign smell appears, immediately stop using the unit, and try to visually determine the cause of the foreign smell, a possible reason is a foreign object present on the heating element, if possible, remove the foreign object from the heating element, otherwise contact the service center.

• Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.

• To avoid damages, transport the unit in the original package.

• Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

• Unpack the unit and remove all the packaging materials.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do not plug it into the mains.
• Make sure that the specified specifications of the power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
• Wipe the convection fan heater body with a slightly damp cloth and then wipe it dry.

ASSEMBLING AND INSTALLATION

Stand mode

• Turn over the unit body. Match the openings on the feet (4) with the corresponding openings in the bottom part of the unit body.

• Fix the feet (4) with the screws supplied with the unit.
  Note: you can install the convection fan heater directly on the feet (4) (pic. 1) or you can insert the wheels (5) into the feet (4).

• Turn over the unit and place it on an even steady surface.

Wall mounting

ATTENTION!
When using the convection fan heater in the bathroom, position the unit so that the distance from the nearest faucet is at least 60 cm, and in no case should splashes of water fall on the body and inside the body of the unit.

Before drilling holes in the wall, make sure that there is no electrical wiring or other communications at this place.

• When mounting the unit on the wall, the distance from all sides of the unit body to any objects should be at least 300 mm (pic. 2), the main socket should be below the level of the unit body and easy to access.
• Do not use the feet (4) with the wheels (5) when mounting the unit on the wall.
• First mark the holes on the wall for the upper brackets (6) (pic. 3).
• Drill two 8 mm holes in the wall to the required depth.
• Insert the dowels (pic. 3) into the drilled holes and tighten the fixing screws so that the fixing screw goes into the bracket (6).
• Align the screw caps with the holes in the upper wall bracket (6), slide the unit to the left and lower it down, making sure the convection fan heater hangs evenly (pic. 4).
• Mark the places for drilling holes on the wall for the lower brackets (6).
• Remove the unit from the wall.
• Drill 8 mm holes in the wall to the required depth for the lower brackets (8).
• Insert the dowels into the drilled holes.
• Align the screw caps with the holes in the upper wall bracket (6), slide the unit to the left, and lower it down, making sure the convection fan heater is fixed properly on the upper brackets (6).
• Fix the lower brackets (6) with two screws, and make sure that the convection fan heater is fixed properly on the wall (pic. 5).

USING THE CONVECTION FAN HEATER

• Place the convection fan heater vertically on even dry moisture- and thermal-resistant surfaces, do not place it horizontally, and do not turn it over.

• Use only the feet (4) or insert the wheels (5) in the feet (4) when placing the unit on the floor.

• Do not place the convection fan heater on soft surfaces, such as carpets with high piles, sofas, or beds.

• The distance between the convection fan heater and the furniture should be at least 1 m.

• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

• Insert the power plug into the main socket.

• Set the power switch (3) to the required position:

  • «0» —the unit is off;
  • «I» — the unit is switched on.

• Turn the thermostat knob (2) clockwise as far as it will go. When the air temperature in the room reaches the desired value, turn the thermostat knob (2) counterclockwise until you hear a distinctive click; in this position, the thermostat will maintain the set air temperature in the room automatically.

• To increase the air temperature in the room, turn the thermostat knob (2) clockwise and counterclockwise to decrease it.
  Note: the fan heater will not switch on if the thermostat settings correspond to the air temperature in the room.

• After operation turn the thermostat knob (2) counterclockwise until bumping, set the power switch (3) to the position «0» and unplug the unit.

Note:
when you switch the unit on for the first time, some smoke or foreign odor may appear. It is normal and not covered by warranty.

AUTOMATIC EMERGENCY SWITCH-OFF FUNCTION IF THE OUTGOING AIR IS TOO HOT

• If the outgoing air temperature exceeds the acceptable value, the automated thermal switch will switch off the convection fan heater.
• Set the power switch (3) to the position «0» and unplug the unit, let the unit cool down for approximately 15-25 minutes (depending on the air temperature in the room) and only after that you can switch the unit on again.
• Make sure that the upper and bottom air grids are not blocked with foreign objects.
• Insert the power plug into the mains socket and switch the unit on.
• If the convection fan heater does not switch on, it may be caused by another malfunction. In this case apply to a service center for repairing of the unit.

PROTECTION FROM DROPPING

• If the convection fan heater accidentally falls or tilts too much, the fall protection system will switch off the unit.
• Set the convection fan heater into the vertical position, and the unit will resume operation.

Note: place the unit on an even dry and steady surface to prevent it from dropping.

CLEANING AND MAINTENANCE

• Before cleaning the convection fan heater set the power switch (3) to the position «0», and make sure that the power plug is not inserted into the mains socket.
• Wipe the unit body with a slightly damp cloth and then wipe it dry.
• Do not use liquid detergents, abrasive cleaners and any solvents to clean the unit.
• To avoid the risk of electric shock provide that no water or other liquid gets into the unit body.
• To clean the air grids, use a vacuum cleaner with a corresponding attachment.

STORAGE

• After cleaning put the convection fan heater away for storage in a dry cool place away from children and disabled persons.
• Before using the convection fan heater next time, it is recommended to check the heater operability and integrity of the power cord and plug.

DELIVERY SET

1. Convection fan heater – 1 pc.
2. Feet – 2 pcs.
3. Wheels – 4 pcs.
4. Working instruction – 1 pc.

TECHNICAL SPECIFICATIONS

• Power supply: 220-240 V, ~ 50-60 Hz
• Rated input power: 1500 W
• Heating area: 20 m²
• Protection degree: IP24

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after the expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.

The manufacturer reserves the right to change the design, structure and specifications not affecting the general operating principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

Hergestellt für «Ruste GmbH», Berggasse 18/18, 1090 Wien, Osterreich
Produced for «Ruste GmbH», Berggasse 18/18, 1090 Vienna, Austria.

References

• BRAYER - официальный сайт австрийского бренда бытовой техники

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>