AFTERSHOKZ AEROPEX Bone Conduction Headphones User Guide
- June 5, 2024
- AfterShokz
Table of Contents
User Guide
How to Set Up Aeropex
-
Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete. -
Pair
Start with your headphones off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue. -
Connect
Open your device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue one time.
Multifunction Button (A)
Function | Action | Prompt / “Audrey Says” |
---|---|---|
Play/pause music | Click once | One beep |
Skip to the next song | Double-click while music is playing | One beep |
Skip to the previous song | Three click | |
while music is playing | One beep | |
Answer call | Click once | Two beeps |
End call | Click once | One beep |
Answer call waiting and hang up on current caller | Press and hold for 2 | |
seconds | One beep | |
Reject a call | Press and hold for 2 seconds | Two beeps |
Prompt devices voice assistant | Press and hold for 2 seconds | Device beep |
Redial last number | Double-click (when idle) | Redial last number |
Volume+ / Power Button (B); Volume- Button (C)
Function | Action | Prompt / “Audrey Says TM” |
---|---|---|
Power on | Press and hold volume+ for 2 seconds | “Welcome to AfterShokz” |
Power off | Press and hold volume+ for 3 seconds | “Power off” |
Mute | Press and hold both buttons for 2 seconds while on a call | “Mute on” or |
“Mute off”
Change EQ setting| Press and hold both buttons for 3 seconds while music is
playing| “EQ changed”
Check battery status| Click the volume+ or volume- button while music is
paused| “Battery high/Battery medium/Battery low/Charge me”
Adjust volume| Click the volume+ or volume- button to adjust the volume while
music is playing| One beep
Specifications
Part number | AS800 | Frequency response | 20Hz~20KHz |
---|---|---|---|
Speaker type | Bone conduction transducer | Sensitivity | 105 ± 3dB |
Bluetooth® version | Bluetooth ® v5.0 | Microphone | -38dB ± 3dB |
Wireless range | 10 m | Battery | Li-Polymer battery |
--- | --- | --- | --- |
Compatible profiles | A2DP, AVRCP, HSP, HFP | Weight 26 g | |
Continuous play | Up to 8 hours | Standby time Up to 10 days | |
Charge time | 2 hours | Warranty 2 years | |
Frequency band | 2402MHz-2480MHz | Maximum RF output power dBm | |
Charge voltage | 5V±5% | Water-resistance IP67 | |
Speaker impedance | 8.5ohm±20% | Battery capacity 145 mAh |
LED Indicator
Solid red | Charging |
---|---|
Solid blue | Charging complete |
Flashes of red and blue | Pairing mode |
Flashes blue | Incoming call |
Flashes red every 2 minutes | Low battery |
Multipoint Pairing
Multipoint pairing allows Aeropex to be connected to two devices at once, allowing users to seamlessly transition between the two.
- Start with your headphones off.
- Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
- Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled.”
- Open your first device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected”
- Turn your headphones off.
- Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
- Open your second device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected.”
- Turn your headphones off.
- Turn your headphones on. Your headphones are now connected to both devices.
- To turn multipoint pairing off: Press and hold the multifunction button and volume- button for 3 seconds. Audrey says “multipoint disabled.”
More information: bit.ly/ASMultipoint
Moisture Detected Alert
This device can detect liquid residue. During charging, if there is sweat or other liquid residues in the charging interface, the device’s light will flash blue and red. The core of the headphones will also vibrate and emit a “Beeb Beeb” warning sound. Please dry the liquid on the charging port and then the device can be charged normally.
How to Reset Your Headphones
- Start with your headphones off.
- Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
- Press and hold the multifunction button, volume+ button, and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
- Turn your headphones off. Aeropex is now reset and can be re-paired to your device.
Optional Accessories
Earplugs (D)
Use headphones in environments where it is safe to block out ambient noise,
such as on a train or airplane.
- Roll earplugs firmly between fingers and place them in the ears.
- To adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
- Switch EQ to the original setting when you take out the earplugs.
Manufacturer
AfterShokz LLC
6057 Corporate Dr., East Syracuse, NY 13057
Let us take care of you! We’ve got your back against defects.
Register your Aeropex at
register.aftershokz.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>