Alpine Corporation MLT100 Mirror Waterfall Fountain Owner’s Manual

: August 10, 2024
: Alpine CORPORATION

Table of Contents

Alpine Corporation MLT100 Mirror Waterfall Fountain
WHAT’S INCLUDED
FEATURES
SPECIFICATIONS
ASSEMBLING & USING YOUR PRODUCT
TROUBLES HOOTING
LIMITED WARRANTY INFORMATION
FREQUENTLY ASKED QUESTIONS
VIDEO – PRODUCT OVERVIEW
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Alpine Corporation MLT100 Mirror Waterfall Fountain

WHAT’S INCLUDED

Fountain Top
Fountain Base
Fountain Pump
Fountain Tray with Light
Replacement Light
Pump Valve
Transformer
Sponge
Bag of Rocks
Cleaning Brush
Cleaning Cloth

FEATURES

SPECIFICATIONS

Power Requirements ………Standard Household 120V
Water Capacity ……………..6-½ US Gallons / 25 Liters
Tubing Diameter ……………………………………….¾” I.D.

ASSEMBLING & USING YOUR PRODUCT

Unpack all components carefully. Please check to ensure all parts have been removed from the packaging. Some splashing may occur when the product is in use.

Place the fountain base on a smooth & level surface. Allow enough space to access the pump. Place the Fountain Top into the Fountain Base with the mirror facing forward. ⚠ CAUTION: It’s important to lean the fountain up against a wall until filled with water, or the fountain will tip over.
Next tighten the wing nuts preinstalled into the Fountain Base This will secure the Fountain Top.
Remove the pump from its packaging and adjust the flow control to the lowest setting to avoid splashing until the fountain is completely assembled.
Place the Pump and Pump Valve into the Fountain Base. Connect the Pump to the Valve first, then connect the Valve to the PVC connector of the Fountain Top.
Next place the supplied Sponge under the Pump. This will help the Pump from excess vibration in the Fountain Base.
Place the Fountain Tray onto the Fountain Base, and route the light cord through the Hole in the Tray then into the Base. Next Route both the Pump and Light cords through the hole in the back of the Fountain.
Pull out the light cord plug through the back opening & connect to the transformer.
Gently pour water into the fountain basin, being careful not to overflow and cause splashing. Make sure the water completely submerges the pump and the water runs clear during operation.
NOTE: We recommend that you use distilled water to prevent scale build- up. The first time you operate the pump it can take up to 5 minutes for the air to be completely expelled and water begins to flow properly
Plug the pump and light cord into your local power supply. Make sure that there is no water around the plug & always keep the power source in a dry place.
Finally add Rocks to your Fountain Tray and enjoy your new Fountain. Don’t forget to add water regularly as water will evaporate over time.

REPLACEMENT PART ITEM#

Submersible Stream Pump ………….PAD900
Replaceable Transformer ……….……..PL022T
Replacement Light Bulb ………………RBS1210

ALSO AVAILABLE FROM ALPINE

Fountain Care Formula ………………..PPL102
Foam and scale remover for indoor and outdoor fountains.

TROUBLES HOOTING

If you have any questions and/or problems, please contact the retail store you purchased this fountain.

If your pump fails to run

Check the circuit breaker or try a different outlet to make sure the pump is receiving electrical power.
Check the pump discharge and tubing for any kinks and/or obstructions
Any buildup obstructing the water flow can be flushed with a garden hose
Check the rotor by removing the front cover & plate to access the impeller area. Turn the rotor and make sure that the rotor is not jammed or broken

If your pump “spews”

Check the water level to make sure the pump is completely submerged and there is enough water in the basin to operate your fountain. Not having enough water will cause your pump to spew

If your pump is making abnormally loud noises

Disconnect the pump from the electrical power supply and remove the front cover & plate
Carefully grip the impeller and gently pull the impeller/rotor assembly out of the pump housing
Rinse the impeller/rotor assembly and clean the cavity with clean water. If breakage or damage is found, contact your local retailer for parts.

CAUTION

Always unplug the pump from the electrical outlet before cleaning & handling
Use with clean water only, do not place the fountain and/or parts in any other liquid.
Periodically change the water & clean the pump to keep free from microorganisms
Disconnect and store the unit in a dry place if not in use for an extended period of time
Do not operate with water above 90°F or 30°C
Do not lift, carry, or pull the pump by the power cord
Do not exceed the maximum voltage & wattage on the transformer
NEVER LET THE PUMP RUN DRY

LIMITED WARRANTY INFORMATION

Thank you for choosing an Alpine product! We aim to please with our wide range of products including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed from the highest quality materials. In the event that we have not achieved our usual standard of excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of purchase, with the purchase date clearly indicated, must be provided. Photos of defective merchandise will also be required to help distinguish the actual cause of the defect. Please read below for a detailed description of warranty coverage.

Water Damage Alpine products are not manufactured to withstand extreme temperatures. Improper storage that allows water to freeze within a product may cause damage, is considered negligence, and will not be covered under this warranty. The use of “hard water,” and/or caustic cleaners, can affect the painted or other finishes. Failure to keep the unit clean, and use of such additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for some splashing to occur, and protecting the immediate surfaces is not the responsibility of Alpine Corporation.
Paint & Color (Retention and/or Loss) The use of water will cause natural erosion to the color. This area can be touched up using standard paint. The paint is designed to protect the entire finish against the breakdown of color. As with any product, all finishes with time will gradually fade and discolor. The warranty will only cover against severe or complete fading, within the first year from date of purchase, with the above exclusion.
Procedure/Service Should a warranty/claim be needed, you should contact the retailer from whom you purchased the product. If that is not an option, you can contact Alpine Corporation at www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to show proof of purchase and provide photographs and any other information needed to validate your claim. This may be necessary to distinguish between a partial or complete replacement of a defective product. The warranty does not cover any items with multiple parts; the warranty will ONLY cover the individual component of the unit/item that may be defective. Replacement parts can be made available to a consumer through the original selling party, or an approved parts retailer. If this is not an option, contact our customer service department. Item is covered under a one-year limited warranty from the date of purchase. When requesting replacement parts due to a warranty claim after 30 days of purchase, credit card information will be requested for shipping charges.

Not Covered Under Warranty

The limited warranty will NOT cover cases of damages due to:

Damages caused in Transit
Inadequate care and/or neglect
Environmental and/or natural elements
Immersion in water, unless specified
Improper Installation/Storage and/or Maintenance

This warranty is void if the product has been damaged by accident, misuse, negligence, improper installation, and/or modifications have occurred. This includes any and/or all defects arising out of freezing water damage, hard water damage, failure to keep the unit clean and free of harmful additives such as bleach, chlorine, etc…. which affect the paint and/or parts. This warranty also does not cover any additional charges or installation, removal, disposal, and/or shipping costs or consequential damage associated with any warranty claim.

Purchased your product online?

We would really appreciate it if you could share your experience with others by reviewing our product on the website from which you purchased it.

Have Questions or Issues? Need help with assembly? Contact us and we will resolve them within 12 hours.

Support Hours: M-F 7:30–5:00 (U.S. Pacific Time)
Call: 877-460-4511
Email: info@alpine4u.com

FREQUENTLY ASKED QUESTIONS

What are the dimensions of the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The Alpine Corporation MLT100 Mirror Waterfall Fountain measures 24 inches in length, 10 inches in width, and 72 inches in height, making it a striking and tall water feature for any space.

What is the price of the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 model is priced at $583.00, reflecting its size, quality, and the visual impact it offers as a decorative piece.

How much does the Alpine Corporation MLT100 Mirror Waterfall Fountain weigh?

The MLT100 fountain weighs 43 pounds, providing a solid and stable structure that is unlikely to tip over easily.

What are the power requirements for the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 model requires a standard household 120V power source, making it easy to install and use in most indoor settings.

What is the water capacity of the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 fountain has a water capacity of 6-½ US gallons (25 liters), ensuring a continuous and steady flow of water.

What is the tubing diameter of the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 model features a tubing diameter of ¾ Inches I.D (inside diameter), which helps facilitate the water flow from the reservoir to the top of the fountain.

How do you set up the Alpine Corporation MLT100 Mirror Waterfall Fountain?

Setup involves assembling the fountain, connecting the pump to the tubing, filling the reservoir with water, and plugging it into a 120V power outlet.

What are the benefits of the mirror feature in the Alpine Corporation MLT100 Waterfall Fountain?

The mirror in the MLT100 model enhances the visual impact of the water flow, reflecting light and surroundings, and creating a sense of depth and tranquility in the room.

What is the warranty period for the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 fountain comes with a 1-year warranty, covering manufacturing defects and providing support for repairs or replacements if needed.

What type of maintenance is required for the Alpine Corporation MLT100 Mirror Waterfall Fountain?

Maintenance includes regular cleaning of the mirror, pump, and tubing, checking for debris, and ensuring the water level remains sufficient for continuous operation.

Who manufactures the Alpine Corporation MLT100 Mirror Waterfall Fountain?

The MLT100 model is manufactured by Alpine Corporation, a reputable company known for producing high-quality decorative water features and garden products.

What should I do if the Alpine Corporation MLT100 Mirror Waterfall Fountain stops working?

Ensure the fountain is connected to a working power source and that the pump is fully submerged in water. If the fountain still doesn’t work, inspect the pump for clogs or damage, and clean or replace it if necessary.

Why is the water flow in my Alpine Corporation MLT100 Mirror Waterfall Fountain weak?

Weak water flow can result from low water levels, debris blocking the pump, or a kink in the tubing. Make sure the reservoir is filled to the correct level, clean the pump, and check the tubing for any blockages or kinks.

What should I do if the Alpine Corporation MLT100 Mirror Waterfall Fountain is making excessive noise?

If the fountain is louder than usual, it might be due to the pump not being fully submerged, low water levels, or vibrations from the surface it’s placed on. Add more water, ensure the fountain is on a stable surface, and consider placing a soft pad underneath to reduce noise

How can I prevent streaking or water spots on the mirror of the Alpine Corporation MLT100 Mirror Waterfall Fountain?

To prevent streaks or water spots, clean the mirror regularly with a soft, lint-free cloth and a non-abrasive cleaner. Using distilled water in the fountain can also minimize mineral deposits that cause streaks.