AFTERSHOKZ AS800 Aeropex Open-Ear Bluetooth Wireless Bluetooth Headphone User Guide
- June 5, 2024
- AfterShokz
Table of Contents
Aeropex
User Guide
How to Set Up Aeropex
-
Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete. -
Pair
Start with your headphones powered off. Enter pairing mode by pressing and holding volume+ until the LED indicator flashes red and blue. -
Connect
Open your device’s Bluetooth® settings and select “Aeropex by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue.
Multifunction Button (A)
Function | Action | Prompt/Audrey Says |
---|---|---|
Play/pause music | Click once | One beep |
Next song | Double-click while music is playing | One beep |
Previous song | Triple-click while music is playing | One beep |
Answer call | Click once | Two beeps |
End call | Click once | One beep |
Answer call waiting and end the current call | Press and hold for 2 seconds |
One beep
Ignore a call| Press and hold for 2 seconds| Two beeps
Activate voice assistant| Press and hold for 2 seconds| Device beeps
Redial last number| Double-click on standby| ‘Redial last number’
Power/Volume+ (B); Volume- (C)
Function | Action | Prompt / “Audrey Says™” |
---|---|---|
Power on | Press and hold volume+ for 2 seconds. | “Welcome to AfterShokz.” |
Power off | Press and hold volume+ for 3 seconds. | “Power off” |
Mute | Press and hold both buttons for 2 seconds while on a call | “Mute on” or |
“Mute off”
Change EQ setting| Press and hold both buttons for 2 seconds while music is
playing| “Equalization changed”
Check battery status| Click the volume up or down button while music is
paused| “Battery high, medium, low (or) charge me”
Adjust volume| Click the volume+ or volume- button
to adjust volume while music is playing| One beep
Specifications
Part number | AS800 | Frequency response | 20Hz~20KHz |
---|---|---|---|
Speaker type | Bone conduction transducer | Sensitivity | 105 ± 3dB |
Bluetooth® version | Bluetooth® v5.0 | Microphone | -38dB ± 3dB |
Wireless range | 10 m | Battery | Li-Polymer battery |
Compatible profiles | A2DP, AVRCP, HSP, HFP | Weight | 26 g |
Continuous play | Up to 6 Hours | Standby time | Up to 10 days |
Charge time | 2 hours | Warranty | 2 years |
Frequency band | 2402MHz~2480MHz | Maximum RF output power | 5dBm |
Maximum Charge Voltage | 5V±5% | Water-resistance | IP67 |
Battery Capacity | 145 mAh |
LED Indicator
Solid red | Charging |
---|---|
Solid blue | Charging complete |
Flashes of red and blue | Pairing mode |
Flashes blue | Incoming call |
Flashes red every 2 minutes | Low battery |
Multipoint Pairing
Multipoint Pairing allows Aeropex to be connected to two devices, allowing users to seamlessly transition between the two.
- Start with your headphones powered off.
- Press and hold volume+ the LED indicator flashes red and blue.
- Press and hold the Multifunction Button and Power/Volume+ Button for 3 seconds. Audrey says “multipoint enabled.”
- Open your first device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected”.
- Turn your headphones off.
- Re-enter pairing mode by pressing and holding the Power/Volume+ Button the LED indicator flashes red and blue.
- Open your second device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected.”
- Turn your headphones off.
- Turn your headphones on. Your headphones are now connected to both devices.
- To turn off the Multipoint Pairing function: Repeat Steps 1 and 2. Then press and hold the Multifunction Button and Volume- Button for 3 seconds until you hear “multipoint disabled.”
Moisture Detection Alarm
These headphones can detect liquid such as water, sweat, and rain. If the headphones are plugged into the charger while wet, the LED indicator will flash red and blue. The headphones will also vibrate and emit a beep. If this happens, remove the charging cable from the headphones, dry them completely and then proceed with charging.
How to Reset Your Headphones
- Start with your headphones powered off.
- Enter pairing mode by pressing and holding volume+ until the LED indicator flashes red and blue.
- Press and hold the Multifunction Button, Power/Volume+ Button, and Volume- Button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
- Turn your headphones off. Aeropex is now reset and can be re-paired to your device.
Optional Accessories
Earplugs (D)
Use headphones in environments where it is safe to block out ambient noise,
such as on a train or airplane.
- Roll earplugs firmly between fingers and place them in the ears.
- While music is playing adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
- Switch EQ to the original setting when you take out the earplugs.
Manufacturer
AfterShokz LLC
3200 Gracie Kiltz Lane, Suite 400 Austin, TX 78758
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>