AFTERSHOKZ AS660 OpenMove Wireless Bone Conduction Open-Ear Bluetooth Headphones User Guide

AFTERSHOKZ AS660 OpenMove Wireless Bone Conduction Open-Ear Bluetooth

Headphones

How to Set Up OpenMove

1. Charge
   Charge the headphones with the included Type-C charging cable. The LED indicator will change from red to blue when charging is complete.

2. Pair
   Begin with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.

3. Connect
   Open your device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey will say “connected” and the LED indicator will flash blue one time.

Multifunction Button (A)

Volume+ / Power Button (B); Volume- Button (C) How to Reset Your Headphones

“Mute off”
Switch EQ| Press and hold both buttons for 3 seconds while music is playing| “Balance mode / Bass booster mode/ Vocal booster mode / Treble booster mode/

Standard mode / Ambient mode Earplug mode / Driving mode”

Check battery status| Click the volume+ or volume- button while music is paused| “Battery high/Battery medium/ Battery low/Charge me”
Adjust volume| Click the volume+ or volume- button to adjust volume while music is playing| One beep

Specifications

Model number                                              S661| Frequency response             20Hz – 20kHz
---|---
Speaker type Bone conduction transducer| Speaker sensitivity 96 ± 3dB
Bluetooth® version| Bluetooth® v5.0| Microphone| sensitivity -40 ± 2dB
---|---|---|---
Wireless range| 10 m| Frequency band                  2402 – 2480MHz
Battery  Rechargeable Li-Polymer battery| Battery capacity 135 mAh
Continuous play| Up to 6 hours| Standby time                             Up to 10 days
Charge time| 2 hours| Charge voltage                                5.25V ± 5%
Charge type| Type-C| Speaker impedance                  8.0 ± 0.5ohm
Water resistance| IP55| Maximum RF output power                4dBm
Weight| 30g| Warranty                                                    2 years
Compatible profiles| HSP, HFP, A2DP AND AVRCP|

LED Indicator

Multipoint Pairing

Multipoint pairing allows OpenMove to be connected to two devices at once, allowing users to seamlessly transition between the two.

1. Begin with your headphones powered off.
2. Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
3. Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled”.
4. Open your first device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey says “connected”.
5. Turn your headphones off.
6. Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
7. Open your second device’s Bluetooth® menu and select “OpenMove by AfterShokz.” Audrey says “connected”.
8. Turn your headphones off.
9. Turn your headphones on. Your headphones are now connected to both devices. Audrey says “connected” and “device 2 connected”.
10. To turn multipoint pairing off: Press and hold the multifunction button and volumebutton for 3 seconds. Audrey says “multipoint disabled”.
    More information: bit.ly/aftershokzpairing

How to Reset Your Headphones

1. Begin with your headphones powered off.
2. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
3. Press and hold the multifunction button, volume+ button and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
4. Turn your headphones off. OpenMove is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)
Use earplugs with headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

1. Roll earplugs firmly between fingers and place in ears.
2. To adjust EQ settings for earplugs, press and hold volume+ and volume- buttons simultaneously while music is playing. Continue through options until “earplug mode.”
3. Switch EQ to other settings when you take out the earplugs.

Storage and Maintenance

• Store the headphones in cool and dry place. The working temperature should be 0~45°C (32~113°F). Working in cold/hot environment or highly humid area may reduce the life of battery.
• After storage for a long period, please charge the headphones before using again.
• The headphones are water resistant, but are NOT waterproof. Please DO NOT submerse the headphones in water
• Listening with headphones at high volume may affect your hearing and the audio will be distorted.
• Clean the headphones with a soft dry cloth.
• Do not charge right after exercising, in case there’s sweat inside the charging port, which could lead to circuit burning while charging.
• Keep the charging port dry before connecting to charger will reduce the risk.
  Note: Design and specification are subject to change without notice. For the most up-to- date product information, please visit www.aftershokz.com.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies  with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption rate (SAR).

Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s): Operation is subject to the following Two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Manufacturer Declarations

Warranty
AfterShokz LLC gives a warranty of 24 months on this product.For the current warranty conditions, please visit our website at www.aftershokz.com or contact your AfterShokz partner. Before putting the product into operation, please observe the respective country specific regulations.

Battery
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Sound Pressure
Excessive sound pressure from earphones and headphones can cause hearing loss.

WEEE Declaration of Conformity
This WEEE logo means that this product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

CE Declaration of Conformity
Hereby, AfterShokz LLC declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and all other applicable EU Directive requirements. The complete declaration of conformity can be found at: https://aftershokz.com/pages/policies.

References

• Terms of Service & Warranty – Shokz

• Terms of Service & Warranty – Shokz

• Shokz Official | The Professional Bone Conduction Headphones Pioneer

• Słuchawki kostne Aftershokz. Słuchawki z przewodnictwem kostnym

• Terms of Service & Warranty – Shokz

• Wsparcie – Dystrybutor Skullcandy i Aftershokz

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>