WFLY X9 2.4GHz 9CH FHSS LoRa Radio Transmitter Instruction Manual
- June 5, 2024
- WFLY
Table of Contents
X9 Quick Instruction Manual
WFLY-RC radio manufacturer since 2004
Thank you for purchasing WFLY surface radio X9! WFLY X9 Is a great radio set
with a lot of exciting functions. We are confident that you will find lots of
Joy and fun with this radio system.
Shenzhen WFLY Technology Development Co.Ltd
Address:C3 building.Xiang Industry Park.Heping Mops Road.Fuyong Town.Baoan
District.Shenzhen.Cuangdong ProvInctChina.
Emall:servIceewflysz.com
Websitcwww.wflysz.com
-
Turn on and off your radio Power on the Transmitter:
Firstly press and hold the power button for 3 seconds to turn on your transmitter. Receiver: After the transmitter is powered on, then switch on your receiver
Power off Receiver: Please switch off the receiver Transmitter: Press and hold the power button for 3 seconds to shut down. -
Power supply range Your radio is compatible with 3.5V-6V (exceeding the power supply voltage may cause damage to your radio)
Note: You can charge the radio if it is powered by a single lithium battery. DO NOT charge your radio If 4 AA dry batteries are Inside the battery compartment. -
After-sales policy Should you have any question or doubt when you are driving this radio, please contact our sales staff. We would be glad to be of any assistance and support.
Product parameters:
Radio parameters:
Model Name: X9 Channel: 9 channels
Working voltage: 3.5V-6.0V
Working current: 220mA
Application: RC cars. boats. tanks. etc.
Resolution: 4096
Frequency band: 2.4GHz (two-way)
Storage: 40 models memory
Language: Chinese, English
Upgrade: USB online upgrade
Display: 3.5′ 480’320 capacitive touch screen
Voice: support voice broadcast
S.Names of radio parts
Receiver parameters:
Model name: RG206S
Frequency band: 2.4GHz
Working voltage: 3.5V-9.0V
Working current: 95mA
Application: RC cars, boats. tanks, etc.
Resolution: 4096 PWM:6 channels
PPM: support
W.BUS: support S.BUS
Two way transmission: Support
Upgrade: USB online upgrade Dimenion:33.6’22.3’12.3mm
Name of radio parts
| 
| 
---|---|---
Description of the home screen:
1. Model name
2. Receiver signal strength
3. Condition mode
4. Transmitter battery
5. Timer(Default:PS1)
6. Telemetry data: Receiver voltage
7. Telemetry data: External voltage
8. Telemetry data: Model speed| 9. Steering trim(Default control: DTI )
10. Throttle trim (Default)
11. Dual rate (default control: DL)
12. Channel view
13. Menu
14.Lock screen button: long press for 2 seconds to lock/unlock the screen 15.
User menu (default control: Ps2)
---|---
Link
Warning: When linking, please be careful not to connect the power
equipment. and be careful that the sudden output of the engine may cause a
shock hazard.
To ensure safety. please do not perform code matching operations when the
motor and engine are running.
Path: (Menu]-(Linkage menu]-[Link]
Linking method: Transmitter: Click the start button to enter the link-state
Receiver: Power on. press and hold the [SET] button for 3 seconds. the orange
LED flashes.
Authentication method: Successful linking: The receiver LED light becomes
green and steady
Connect the servo: Operate the corresponding channel of the transmitter.
linking successfully if the servo has synchronized action.
Note: The distance between the transmitter and the receiver shall be
within one meter. The transmitter cannot be linked In simulator and student
mode. mode modification
Path: [Menu]-[System Menu ]-[Trainer and simulator]
There is no other WFLV 2.4G system in the vicinity that the same protocol is
undergoing binding operation. During the binding: If you need to exit.
Touch [Cancel].
Receiver RGB LED status:
| Color | Status | Function |
|---|---|---|
| Green | ON | Link successfully |
| Blue | Flash | Wireless upgrading mode |
| Red | ON | No signal |
| Flash | Voltage <3.7V | |
| Orange | Flash | Link |
Failsafe
Importance of F/S protection setting: If you do not set the F/S protection
data. when the model loses control due to some reason, unexpected and
uncontrollable actions may occur. causing the boat/car/tank to collide/fall.
or even hurt humans. If you set the protection according to the parameters of
the smooth driving in advance. then the chance of colliding. losing. or even
hurting others after losing control will be much less.
Path: [Base setting ]-[Fail safe]
Setting mode: 1 Hold: Hold mode. the value when the receiver output is out of
control (hold action) 2 F/S: Loss of control protection mode. the set value
output by the receiver after loss of control (default action). For safety, it
is recommended to set this out of control protection mode. the throttle
channel is set to brake action. 3 Close: Close the current channel output.
Note: Model fail safe is very important. Failure to set It correctly can
cause damage of your RC model. so you must be very careful when setting this
function.
Warning
Low battery warning When the transmitter voltage. receiver battery voltage and
power battery voltage are lower than the set value (path: [Menu)-[System menu
HBattery )). the radio will broadcast corresponding voice reminders, such as
[transmitter voltage is low. 3.Snand you can set whether to turn on the
vibration reminder as required.
Shutdown alarm interface:
After the telemetry function is enabled, the transmitter will check whether
the receiver is communicating when it is off. and then the warning interface
will pop up to confirm before shutdown.
Touch (Shutdown ] to forcibly shut down the transmitter.
Model menu Path:
[Menu]-(Model Menu]
Switch and channel Settings:
PathiMenuNAdvanced Menu ]-(Channel setting]
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: – Reorient or relocate
the receiving antenna. – Increase the separation between the equipment and
receiver. -Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. -Consult the dealer or an experienced
radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Email:service@wflysz.com
WeChat: WFLY_RC
Facebook: Wfly RC
Facebook group: WFLY RC Groups
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>