CL101A AfterShokz Loop100 USB-A Bluetooth Adapter User Guide
- June 4, 2024
- AfterShokz
Table of Contents
AfterShokz Loop100 USB-A Bluetooth® Adapter
Model: CL101A
QUICK START
*Compatible products: OpenComm, OpenComm UC
Pairing
- Start with OpenComm turned off. Press and hold the Volume+ button until the LED Indicator flashes red and blue.
- Plug the USB adapter into a USB port on your PC. The LED will flash blue rapidly.
- Connection is established when Audrey says “Connected” or beeps. The LED on the USB adapter is solid blue.
- To play music or take calls on the headset, please check, and ensure the “AfterShokz Loop100” is the default input and output device in your operating system’s audio settings.
Multifunction Button (Designer will put the chart into the graphic presentation)
Multifunction Button | LED |
---|---|
Function | Action |
Pair to a headset | Press and hold for 2 seconds |
Reconnect to the last connected headset | Click once |
Reset the adapter | Press and hold for 2 seconds, then double-click |
blue then turns solid blue for 5 seconds, then flashes blue rapidly
LEGAL
AfterShokz Loop 100 USB-A
Wireless Adapter
Model CL101A
Safety Instructions
- Store the product in a cool, dry place. The working and storage temperature should be 0°C-55°C (45°F-131°F).
- Never allow children to play with the product – small parts may be a choking hazard.
- Keep the product away from heat sources, direct sunlight, combustible gas, or other liquids.
- Do not disassemble the product.
- Unplug, discontinue use, and contact Shokz if the product overheats or has a damaged outer casing or plug.
Note
Design and specification are subject to change without notice. For the most
up-to-date product information, please visit
www.aftershokz.com.
FCC
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed to comply without
testing of specific absorption rate (SAR).
Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s):
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CE Declaration of Conformity
Shokz Holding Limited hereby declares that this product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU and all other applicable EU Directive requirements. The complete
declaration of conformity can be found at:
https://us.aftershokz.com/pages/policies.
AfterShokz’s EU representative is AfterShokz Euro B.V., Schipholweg 103,
2316XC Leiden, Netherlands.
Frequency: 2400-2483.5MHz | Maximum Power: 5dbm |
---|---|
Input: 5V ****1000mA |
WEEE Declaration of Conformity
This WEEE logo means that this product must not be discarded as household
waste, and should be delivered to an appropriate collection facility for
recycling. Proper disposal and recycling help protect natural resources, human
health, and the environment. For more information on the disposal and
recycling of this product, contact your local municipality, disposal service,
or the shop where you bought this product.
UK Declaration of Conformity
Shokz Holding Limited hereby declares that this product is in compliance with
the essential requirements and all other applicable United Kingdom
regulations. The complete declaration of conformity can be found at:
https://us.aftershokz.com/pages/policies.
AfterShokz’s authorized representative in the UK is Pinpoint Consumer
Electronics Ltd., Unit 35, Meridian House, Road One, Winsford Industrial
Estate, Winsford, Cheshire CW7 3QG.
Manufacturer
Warranty: Shokz Holding Limited gives a warranty of 24 months on this product. For the current warranty conditions, please visit our website at www.aftershokz.com or contact your AfterShokz partner. Before putting the product into operation, please observe the respective country-specific regulations.
Responsible party (contact for FCC matters only): AfterShokz LLC.
3200 Gracie Kiltz Lane, Suite 400 Austin, TX 78758 USA
www.aftershokz.com
Australia/New Zealand
References
- Shokz Official | The Professional Bone Conduction Headphones Pioneer
- Terms of Service & Warranty – Shokz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>