MTX 278003880 Audio Bluetooth System Owner’s Manual
- June 6, 2024
- MTX
Table of Contents
278003880
Owner’s Manual
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact
MTX Technical Support at
1-800-225-5689.
When connecting power and ground wires ensure that the power wire is fused at
the point where it is connected to the vehicle’s battery. Failure to do so can
result in damage to the vehicle if a short circuit develops between the
vehicle connection point and the product.
PRODUCT INFORMATION
Model #——————-
Serial #——————-
Dealer’s Name———-
Date of Purchase——–
BLUETOOTH AUTO-PAIR MODE
Follow these steps to pair the unit to your Bluetooth device:
a. Turn the unit On.
b. Search for BRP Sound System from your device’s Bluetooth menu.
c. Select Pair.
BUTTON FUNCTIONS
| Button | Function |
|---|---|
| POWER (1) | When the device is off, press the Power button to turn it on; When |
the device is on, press and hold the Power button for 3 seconds to turn it
off. The device emits 4 short beeps to indicate that it is switching off.
When not paired with a phone, the device will turn off after 10 minutes. To
avoid battery drain, the sound system can be used for a short time when the
engine is off. Until this short time, the sound system automatically shuts
down.
PLAY/ PAUSE (2)| The Play/ Pause / allows you to play or pause a track with a
single tap.
VOLUME UP (3)| Increase the sound level.
VOLUME DOWN (4)| Decrease the sound level.
PREVIOUS TRACK (5)| Reproduce the previous track.
NEXT TRACK (6)| Reproduce the next track.
Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Declaration of conformity
Hereby MTX Audio declares that this product is in compliance with the essential requirements and other relevant provisions of Directives:
| 2014/53/EU | Radio Equipment Directive (RED) |
|---|---|
| 2014/30/EU | The Electromagnetic Compatibility Directive and its amending |
Directives
2011/65/EU amended by 2015/863| Restriction of Hazardous Substances (RoHS3)
directive
2012/19/EU| Waste of Electrical and Electronic Equipment (WEEE) recast
directive
USA FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canada IC Information
CAN ICES-3(B)/NMB-3(B)
CAN ICES-3(B)/NMB-3(B)
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
FCC/ IC Radiation Exposure Statement
This equipment complies with FCC and IC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
NOTES
© 2021 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek
Corporation. Designed and Engineered in the U.S.A. Due to continual product
development, all specifications are subject to change without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
1-800-225-5689
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>