MTX AUDIO X3-17-SW-D Can AM Maverick X3 Driver Subwoofer Enclosure Owner’s Manual
- June 3, 2024
- MTX Audio
Table of Contents
X3-17-SW-D Can-AM Maverick X3 Driver Subwoofer Enclosure
Owner’s Manual 
X3-17-SW-D Can-AM Maverick X3 Driver Subwoofer Enclosure
X3-17-SW-D CAN-AM® MAVERICK X3 DRIVER SUBWOOFER ENCLOSURE
OWNER’S MANUAL
MTX.COM
THANK YOU
Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit
subwoofer enclosure designed for the Can-Am® Maverick X3. Our sub enclosure,
with its 3512-04S 12″ shallow subwoofer, will belt out the bass and deliver
ground-pounding audio making you the party vehicle in any ride! With a few
basic hand tools in your trusty toolbox, you can have this installed in no
time. So, what are you waiting for? It’s time to get the rumble in your ride
and go hit the trails! Oh, and congratulations on your purchase, thanks for
your support and most importantly, enjoy the ultimate audio experience with
MTX!
WE’RE HERE TO HELP
We’re here to help with any installation or technical support. Visit
mtx.com to chat, call
1-800-225-5689 to speak with an MTX
Technical Support representative, or visit
youtube.com/user/MTXAudioUSA to view
product videos.
DON’T FORGET TO REGISTER YOUR PRODUCT
Don’t forget to register your new MTX Audio product. Visit
mtx.com/productregistration or scan the
QR code to the right.
Model #…………………………..
Serial #……………………………….
Dealer’s Name………………………..
Date of Purchase……………………..
IMPORTANT NOTICE
Whenever working on the vehicle, it is recommended to disconnect the battery
prior to starting work. Failure to do so may lead to a risk of electric shock
or equipment damage.
When connecting power and ground wires ensure that the red power wire is fused
at the point where it is connected to the vehicle’s battery. Failure to do so
can result in damage to the vehicle if a short circuit develops between the
vehicle connection point and the product.
FEATURES
- Includes an MTX 3512-04S 12″ Shallow Subwoofer
- Mounts Under Driver’s Seat
- Factory Matched Texture
- Installer Friendly Design
- Direct Fit, No Cutting or Drilling Required
SPECIFICATIONS
- 12″ Loaded Subwoofer Enclosure
- RMS Power Handling: 300-Watts
- Peak Power Handling: 600-Watts
- Sensitivity (2.83V/1m): 88.5dB
- Sensitivity (1W/1m): 84.4dB
- Frequency Response: 23Hz – 130Hz
- Impedance: 4
FIT GUIDE
Turbo / Max Turbo ………………………………………………….2018 – 2019
Turbo R / Max Turbo R …………………………………………..2017 – 2019
X-DS Turbo …………………………………………………………………2017
X-RS Turbo R / Max X-RS Turbo R …………………………….2017 – 2019
X-DS Turbo R / Max X-DS Turbo R …………………………2018 – 2019
X-MR Turbo ……………………………………………………………2019 – 2021
X-MR Turbo R………………………………………………………….2019
X-RC Turbo ……………………………………………………………2019 – 2021
X-MC Turbo R…………………………………………………………2019
DS Turbo / Max DS Turbo ……………………………………..2020 – 2021
RS Turbo ………………………………………………………………………….. 2020
DS Turbo R / Max DS Turbo R ………………………………..2020 – 2021
Max DS Turbo RR ……………………………………………………………….2020
RS Turbo R / Max RS Turbo R ……………………………………………2020 – 2021
X-RC Turbo RR ……………………………………………………………….2020 – 2021
X-RS Turbo RR / Max X-RS Turbo RR ……………………………….2020 – 2021
X-MR Turbo RR / Max X-MR Turbo RR …………………………………..2020 – 2021
X-MS Turbo RR …………………………………………………………………………..2020
X-DS Turbo RR / Max X-DS Turbo RR ………………………………….2020 – 2021
FIT GUIDE NOTES
Only the X3-17-SW-D driver-side enclosure includes the signal harness from the
amp.
IN THE BOX
- X3-17-SW-D Loaded Subwoofer Enclosure
- Adhesive Foam Tape
- Mounting Hardware (1) Mounting Bracket (5) T40 Torx Bolts
INSTALLATION
Step 1 – Release the lower seat belt strap from the harness by feeding it
back through the tension assembly. This will allow you to feed the shoulder
straps through the hole at the top of the seat.
Step 2 – Remove two (2) 13mm bolts and nuts at the front of the seat
frame.
Step 3 – Access the rear 18mm nuts using a socket with extension either
by aligning the holes in the seat base over the nuts or by sliding the seat
fully forward and reaching behind.
Step 4 – With the seat free, disconnect the seat belt sensor and speed
sensor cables from the seat assembly.
Step 5 – Once disconnected, lift the seat out of the vehicle and set it
aside.
Step 6 – Remove the 10mm M6 bolt holding the brake line clamp in place on
the seat frame.
Step 7 – Remove the cable clamp from the brake line.
Step 8 – Wrap the brake line with the strip of adhesive-backed foam tape
included in the box.
Note: This step is to prevent the brake line from rattling against the
enclosure under high bass output and any chaffing due to the movement of the
brake line while the vehicle is in motion.
Step 9 – Tilt the front of the enclosure down and slide it under the
forward crossbar as you set it in place onto the floor of the vehicle tucking
the brake line into the pre-molded slot in the bottom of the enclosure.
Step 10 – Taking the long bar bracket included, align the slotted holes
with the threaded insets on the top rear of the enclosure. The two large holes
at either end should slide over the threaded seat mounting posts.
Step 11 – Loosely install three (3) T-40 Torx screws into the bracket.
Step 12 – Align the threaded inserts at the front corners of the
enclosure with the holes in the bottom of the seat brackets and insert two (2)
T-40 Torx screws.
Step 13 – Once all fasteners are in place, tighten to secure the
enclosure.
Step 14 – Route the subwoofer cable to the desired connection point.
Note: If installed as part of a kit, the subwoofer plug will connect to
the main harness supplied. If not installed as part of a kit, the plug will
need to be removed and an additional speaker wire added.
Step 15 – With your wire routed and system tested, reinstall the seat in
the reverse order as removed.
Note: In the event of floor pan rattle, included in the subwoofer kit are
a self-tapping drill bit and bolts to allow you to bolt the floor pan directly
to the frame of the vehicle. Please refer to the installation videos for more
information on their use at
www.youtube.com/user/MTXAudioUSA
Step 16 – Reassemble and go ride.
WARRANTY PERIOD
At MTX Audio we engineer products that will stand up to the test of time. We
also realize that from time to time a problem may occur. That’s why our
products carry a 2-year limited warranty that begins at the time of sale to
the end user.
Of course, we’re here to help. If you experience an issue with any of our
products within the warranty period, please contact our customer service
technical line at 1-800-CALL-MTX to help troubleshoot your issue. If, after
speaking with our technical experts it is determined that a problem lies with
the product, the technician will provide you with a Return Authorization
number and all the relevant details you’ll need to get the product taken care
of.
MITEK WARRANTY
MiTek Mobile products (including, but not limited to MTX, Coustic, Streetwires, Xtant, BassSlammer, and Thunder Marine) purchased in the USA from an AUTHORIZED MITEK DEALER are guaranteed against defects in material and workmanship for the period of time specified. The warranty period begins the day the product is purchased by the end user, and this warranty is limited to the original retail purchaser of the product. Products found to be defective during the warranty period will be repaired or replaced with equivalent products by MiTek at no charge. This warranty is void if it is determined that unauthorized parties have attempted repairs or alterations of any nature, and the warranty does not extend to cosmetics or finishes. MiTek disclaims any liability for other incurred or consequential damages resulting from product defects. MiTek’s total liability will not exceed the purchase price of the product.
Let’s Get Social
mtx.com
Like, Follow, & Subscribe
© 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek
Corporation.
All other trademarks are the property of their respective owners.
Designed and Engineered in the U.S.A.
Due to continual product development, all specifications are subject to change
without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
1-800-225-5689
MTX006226 RevA 1/21 · 21A10812 · AW0015867
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>