MTX AUDIO X3-17-DK Can-Am Maverick X3 Dash Kit Owner’s Manual
- June 4, 2024
- MTX Audio
Table of Contents
X3-17-DK
CAN-AM® MAVERICK X3 DASH KIT
OWNER’S MANUAL
X3-17-DK Can-Am Maverick X3 Dash Kit
THANK YOU
Thank you for making the AWESOME decision to purchase our Can-Am® Maverick X3
dash kit designed for use with the MTX Audio AWMC3 Bluetooth all-weather head
unit. This easy to install dash kit is the perfect OEM fit solution for your
Can-Am® Maverick X3. So, congratulations on your purchase, thanks for your
support and most importantly, enjoy the ultimate audio experience with MTX!
WE’RE HERE TO HELP
We’re here to help with any installation or technical support. Visit mtx.com
to chat, call 1-800-225-5689 to speak
with an MTX Technical Support representative, or visit
youtube.com/user/MTXAudioUSA to view
product videos.
DON’T FORGET TO REGISTER YOUR PRODUCT
Don’t forget to register your new MTX Audio product. Visit
mtx.com/productregistration or scan the
QR code to the right.
Model # _____
Serial # _____
Dealer’s Name ____
Date of Purchase __
IMPORTANT NOTICE
Whenever working on the vehicle, it is recommended to disconnect the battery
prior to starting work. Failure to do so may lead to a risk of electric shock
or equipment damage.
When connecting power and ground wires ensure that the red power wire is fused
at the point where it is connected to the vehicle’s battery. Failure to do so
can result in damage to the vehicle if a short circuit develops between the
vehicle connection point and the product.
FIT GUIDE
Turbo / Max Turbo ………………………………………2018 – 2019
Turbo R / Max Turbo R ………………………………….2017 – 2019
X-DS Turbo …………………………………………………..2017
X-RS Turbo R / Max X-RS Turbo R ………………2017 – 2019
X-DS Turbo R / Max X-DS Turbo R ……………..2018 – 2019
X-MR Turbo ……………………………….2019 – 2021
X-MR Turbo R………………………………………..2019
X-RC Turbo ………………………………2019 – 2021
X-MC Turbo R…………………………………………2019
DS Turbo / Max DS Turbo ……………………2020 – 2021
RS Turbo ……………………………………. 2020
DS Turbo R / Max DS Turbo R ……………2020 – 2021
Max DS Turbo RR ………………………………………………2020
RS Turbo R / Max RS Turbo R …………………..2020 – 2021
X-RC Turbo RR …………………………………..2020 – 2021
X-RS Turbo RR / Max X-RS Turbo RR …………………2020 – 2021
X-MR Turbo RR / Max X-MR Turbo RR …………..2020 – 2021
X-MS Turbo RR ……………………………………………2020
X-DS Turbo RR / Max X-DS Turbo RR ……………….2020 – 2021
IN THE BOX
- Dash Kit
- Mounting Hardware
(1) Compression Plate
(2) Compression Plate Screws
(4) Shroud Screws
(2) Source Unit Screws
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
- 1″ Hole Saw
- Torx T8 Screwdriver
- Torx T20 Screwdriver
- Drill and 1/8″ Drill Bit
INSTALLATION
Step 1 – Remove the cover from top center of the dash.
Step 2 – Locate the four (4) dimples formed into the tray area on the top
center dash. Two are located toward the front and two are at the rear under
the cover that was just removed. Using a 1/8″ drill bit, drill through the
dimples just enough to expose the existing boss located below.
Caution: Drilling deeper can damage the bosses beneath and prevent proper
installation of the dash kit.
Step 3 – Using a 1″ hole saw, drill a hole in the top of the dash to pass the
wiring harness through. Our recommended location is indicated in the picture.
Note: The 12-volt power port can be removed and used to pass the harness
through the dash if you do not desire to drill a separate hole. This will
require the removal of the center dash console panel to remove the power port.
Step 4 – Prepare the AWMC3 radio unit by removing the two (2) threaded studs from the back of the radio.
Step 5 – Locate the compression plate (shown) in the kit. Install it loosely as shown into the kit by inserting two (2) short screws included.
Step 6 – Sliding the plate toward the rear of the kit, install the radio into the kit opening from the rear making sure the top of the radio is between the kit face and compression plate. Once in position, press the radio forward into the opening until it is flush with the front and aligned with the pre-molded screw holes.
Step 7 – Using the two (2) longer screws, secure the bottom of the radio to the kit.
Step 8 – While pressing the pressure plate forward against the radio chassis, tighten the two (2) screws left loose in Step 5.
Step 9 – Prepare the pigtail harness supplied with the AWMC3 radio for
installation by connecting additional wire to reach power/ground locations,
speaker wire if needed and amplifier turn-on wire.
Note: If the radio installation is part of a full plug-and-play kit, use
the pigtail supplied with the kit and not the radio. Start the installation by
passing the pigtail harness down through the 1″ hole previously drilled.
Step 10 – At this time, any RCA signal wires should be fed up through the hole for connection to the radio unit. Once wires are in place, make the appropriate connections to the radio.
Step 11 – With connections made, collect the wire harness under the kit shroud and place the radio kit on top of the dash aligning it with the four (4) holes drilled earlier. Making sure all wires are tucked under the kit, secure it in place with the four (4) screws provided
Step 12 – With the radio secure, make the appropriate electrical connections to complete the install such as power, ground and remote turn on for amplifiers.
Step 13 – Reassemble and go ride.
WARRANTY PERIOD
At MTX Audio we engineer products that will stand up to the test of time. We
also realize that from time to time a problem may occur. That’s why our
products carry a 2-year limited warranty that begins at the time of sale to
the end user.
Of course, we’re here to help. If you experience an issue with any of our
products within the warranty period, please contact our customer service
technical line at 1-800-CALL-MTX to help troubleshoot your issue. If, after
speaking with our technical experts it is determined that a problem lies with
the product, the technician will provide you with a Return Authorization
number and all relevant details you’ll need to get the product taken care of.
MITEK WARRANTY
MiTek Mobile products (including, but not limited to: MTX, Coustic, Streetwires, Xtant, BassSlammer, and Thunder Marine) purchased in the USA from an AUTHORIZED MITEK DEALER are guaranteed against defects in material and workmanship for the period of time specified. The warranty period begins the day the product is purchased by the end user, and this warranty is limited to the original retail purchaser of product. Products found to be defective during the warranty period will be repaired or replaced with equivalent product by MiTek at no charge. This warranty is void if it is determined that unauthorized parties have attempted repairs or alterations of any nature, and the warranty does not extend to cosmetics or finish. MiTek disclaims any liability for other incurred or consequential damages resulting from product defects. MiTek’s total liability will not exceed the purchase price of the product.
NOTES
Let’s Get Social
mtx.com
Like, Follow, & Subscribe
© 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek
Corporation. All other trademarks are property of their respective owners.
Designed and Engineered in the U.S.A.
Due to continual product development, all specifications are subject to change
without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
1-800-225-5689
MTX006220 RevA 1/21 · 21A10809 · AW0015864
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>