MTX AUDIO MUD600-1 Mono Block Amplifier Owner’s Manual
- June 3, 2024
- MTX Audio
Table of Contents
MTX AUDIO MUD600-1 Mono Block Amplifier
PRODUCT INFORMATION
- Model #
- Serial #
- Dealer’s Name
- Date of Purchase
INTRODUCTION
Thank you for purchasing this MTX Audio Hi-Performance amplifier. Proper installation matched with MTX speakers and subwoofers provides superior sound and performance for endless hours of enjoyment whether you are waking the neighbors or just out enjoying your tunes. Congratulations and enjoy the ultimate audio experience with MTX!
FEATURES
- Compact Size
- Double Sided PCB
- Surface Mount Components
- MOSFET Design
- LPF Crossover
- Noise Free Design
- Optional Remote Bass Knob (EBC-01)
PANEL LAYOUT
CONTROL FUNCTIONS
-
1. Wiring Harness – All wiring to the amplifier will run through the wiring harnesses. Speakers – Connect subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground. + BATT (+12 Volt Power) – Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery. WARNING: Always protect this power cable by installing a fuse or circuit breaker of the appropriate gauge within 18 inches (45cm) of the battery terminal connection.
Remote Turn On – This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote and turn on the lead of the head unit or signal source.
GND – Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. If a suitable ground point is not available on the frame, or if used in a marine or UTV application, connect this terminal directly to the vehicle battery ground terminal, or any other factory ground points. RCA Input Jacks – This unit is designed to function with source units that feature RCA outputs. If your source unit does not have RCA outputs you will need to use the speaker-level outputs. A source unit with a minimum level of 200mV is required for proper operation. -
Input Level – Allows switching the signal input mode from High (Speaker) level to Low (RCA) Level inputs.
-
Gain Control – The Gain control will match the amplifier’s sensitivity to the source unit’s signal voltage. The operating range is 200mV to 10V. NOTE: This is NOT a volume control.
-
Bass Boost / LPF – These controls allow control over the frequencies played. The Bass Boost allows adjustment of up to 18dB of boost to be applied at 45Hz. The LPF controls the built-in Low Pass Crossover cut-off frequency between 40Hz~250Hz.
INSTALLATION AND MOUNTING
MTX recommends your new amplifier be installed by a 12-volt installation specialist. Any deviation from specified installation instructions can cause serious damage to the amplifier, speakers, and/or vehicle’s electrical system. Damage caused by an improper installation is NOT covered under warranty. Please verify all connections prior to the system turning on.
- Disconnect the vehicle’s negative battery cable.
- Determine the mounting place for your MTX amplifier. Keep in mind there should be sufficient airflow for proper cooling. Mark the mounting holes from the amplifier to be drilled. Before drilling makes sure all vehicle wires, gas lines, brake lines, and gas tank are clear and will not interfere with installation. Drill the desired holes and mount the MTX amplifier.
- Install a positive (+) power cable from the vehicle’s battery through the firewall using a grommet or firewall bushing to avoid cable damage from the sharp edges of the firewall. Run the cable through the interior of the vehicle and connect it to the amplifier’s +12V wire. Do not connect to the battery at this time. NOTE: Use only proper gauge wire for both positive and negative connections.
- Install a circuit breaker or fuse within 18 inches of the battery. This effectively lowers the risk of severe damage to you or your vehicle in case of a short circuit or accident. Make sure the circuit breaker is switched Off or the fuse is taken out of the fuse holder until all connections are made. Now connect your positive power cable to the positive battery terminal of the battery.
- Grounding – Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare metal surface. Attach the amplifier’s ground wire to that contact point. If a suitable location is not available or if used in a marine or UTV application, connect this terminal to the vehicle’s negative battery terminal.
- Connect a Remote Turn-On wire from the source unit to the MTX amplifier’s (REM) wire. If the source unit does not have a dedicated Remote Turn-On lead, you may connect to the source unit’s Power Antenna lead.
- Supply the signal to your MTX amplifier by connecting the signal cables using high-quality RCA or speaker wires to the corresponding outputs at the source unit and inputs of the amplifier.
- Connect your speakers to your MTX amplifier’s speaker wires using the correct gauge speaker wire. Your MTX amp can drive a 2Ω mono minimum load for optimum power.
- Double-check all previous installation steps, in particular, wiring and component connections. Once verified, reconnect the vehicle’s negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.
NOTE:
Gain Levels on the amplifier should be turned all the way down (counter-
clockwise) before proceeding with adjustments.
INSTALLATION
For proper performance and safety, MTX recommends installing an inline fuse
per the owner’s manual instructions according to the following.
- MUD600-1: 60A Fuse
TROUBLESHOOTING
| Problem | Cause | Solution |
|---|---|---|
| Output Distorted | Head Unit Volume Set Too High | Lower Head Unit Volume |
| Amplifier Gain Set Too High | Lower Amplifier Gain |
__
Bass is Weak
| Speakers Wired Out of Phase| Wire Speakers with Correct Phase
Not Using MTX Subwoofers| Buy MTX Subwoofers
__
Blowing Fuses
| Excessive Output Levels| Lower the Volume
Amplifier Defective| Return for Service
For MTX technical support please call 1 800-225-5689 or chat with us online at mtx.com.
SPECIFICATIONS
| Model | MUD600- 1 |
|---|---|
| Description | Class D Mono Amplifier |
Primary Ratings**
Primary Power| 300 W RMS at 4W, 20-165Hz and £ 1% THD+N
Signal-to-Noise Ratio| 85 dBA
Secondary Ratings***
Dynamic Power| 425 W at 4W, £ 1% THD+N
650 W at 2W, £ 1% THD+N
Features
Input Level| 0.2 – 5V Low Level, 0.4 – 10V High Level
Frequency Response| 10Hz – 250 Hz
Low Pass Filter (LPF)| 40-250Hz Variable
Minimum Load| 2W
Low Voltage Protection| Yes, Protect <8.5V
Components & PCB| SMD Parts / Double-Sided FR-4 PCB
Dimensions
Height| 1.85″ (47mm)
Width| 5.51″ (140mm)
Length| 7.36″ (187mm)
Amplifier ratings in accordance with CTA-2006C standards.
WIRING DIAGRAM
4Ω MONO
2Ω MONO
© 2019 Mitek Corporation. All rights reserved. MTX, Mud Nation, and Let’s Do Something Dirty are trademarks of Mitek Corporation. All other trademarks are the property of their respective owners. Designed and Engineered in the U.S.A.
Due to continual product development, all specifications are subject to change
without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
1-800-225-5689
MTX005930 RevA 2/19 • 21A10713 • AW0015728.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>