CLIPSAL MX9K108PP Protection Kit Installation Guide
- July 17, 2024
- CLIPSAL
Table of Contents
CLIPSAL MX9K108PP Protection Kit
Specifications
- 100A MAXBAR+ 1P, 8 MOD
- 100A MAXBAR+ 3P, 18 MOD
- Terminal Block, 100A, 1P
- Terminal Block, 100A, 1P
- Curve, 6000A, 240/415V, RED
- Curve, 6000A, 415V, RED
- Toggle 1P, 32A, C
- Toggle 1P, 32A, C
- Curve, 6000A, 240/415V
- Curve, 6000A, 240/415V
- 30mA, C Curve, 6000A
- 30mA, C Curve, 6000A
Product Usage Instructions
Unboxing
- When unboxing the Protection Kit, ensure all components are present based on the commercial reference numbers provided in the manual.
Description
- For single-phase installations, use the components provided including the MAXBAR+, Terminal Block, Curve modules, and Comb busbar Tooth Cap as specified in the manual.
Three Phase
- For three-phase installations, utilize the MAXBAR+ 3P, Terminal Block, Curve modules, and Comb busbar Tooth Cap as outlined in the manual.
- Note: Ensure to follow the specified positions for device installation to prevent unintended equipment operation.
Additional Information
- Circuit protection devices for SPD are sold separately.
- The last module can be used for a sub-board or a second solar connection if no AC-coupled battery connection is required.
FAQ
Q: What should I do if I notice damage while unpacking the product?
A: If you observe any damage during unpacking, do not install the product and contact the supplier for further assistance.
Q: Can MCBs be replaced with an isolator switch or terminal block?
A: No, do not replace MCBs with isolator switches or terminal blocks as it could result in device damage and potential hazards.
SAFETY INSTRUCTION
PLEASE NOTE
- This equipment must be installed and maintained by a qualified electrician under the appropriate statutory regulations and codes of practice.
- All applicable local, regional, and national regulations must be complied with during the installation, use, maintenance, and replacement of this device.
- This product should not be installed if, when unpacking it, you observe that it is damaged.
- Clipsal cannot be held responsible in the event of non-compliance with the instructions in this document and in the documents to which it refers.
- The service instruction must be observed throughout the lifetime of this product.
DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
- Turn off all power supplying this product before working on it.
- Use a voltage tester with a suitable rated voltage to check that all active conductors are not energized.
- Do not cut the comb busbar.
- Failure to follow these instructions will result in death or serious injury.
WARNING HAZARD OF DEVICE DAMAGE
- Ensure all the connected sources do not exceed 100 A at any one time.
- Do not replace MCBs with an isolator switch or terminal block.
- Failure to follow these instructions will result in death or serious injury.
TOOLS
Unboxing
Description
Single Phase
- A 100A MAXBAR+, 1P, 8 MOD
- B MX9TB1100
- C MX9MC163R
- D MX9R3240
- E MX9MC132
Three Phase
- A 100A MAXBAR+, 3P, 18 MOD
- B MX9TB1100
- C MX9MC363R
- D MX9R3540
- E MX9MC325
- F MX9MC132
WARNING UNINTENDED EQUIPMENT OPERATION
- Ensure that the devices are in specified positions only.
- Failure to follow these instructions can result in death, serious injury, or equipment damage.
Single Phase Comb Busbar
- В МХ9ТВ1100
- C MX9MC163R
- D MX9R3240
- E МХ9МС132
- G MX9MC140 + MX9SP140
- Circuit protection devices and SPD are sold separately from this kit.
- The last module can used for either a sub-board or 2nd solar connection if no AC-coupled battery connection is required.
- Circuit protection device for SPD
- Neutral connection
- Grid connection
- House connection
- EV connection
- Solar connection
- AC coupled battery
For more information on SPD selection & connection, consult the SPN
installation sheet. 
Three-Phase Comb Busbar
- B MX9TB1100
- C MX9MC363R
- D MX9R3540
- E MX9MC325
- F MX9MC132
- The last module can used for either a sub-board or 2nd solar connection if no AC-coupled battery connection is required.
- Neutral connection
- Grid connection
- House connection
- EV connection
- Solar connection
- AC coupled battery
Installation of Devices
Note: For more information, refer to the respective device instruction sheets and technical data sheets.
Installation of Comb Busbar
Single Phase
Note: Remove the protection film from the busbar before installation of
busbar.
Three Phase
Note: Remove the protection film from the busbar before installation of
busbar.
Installation of Toothcap for MX9K108PP, MX9K318PP
Note: For unused tooths on the busbar install tooth caps. (Commercial reference number: RMXPT120).
Typical System Representation
Single Phase Installation
Three Phase Installation
Additional Technical Information
- For more information on additional applications, enclosure compatibility, and FAQs, consult the complimentary guide.
Labeling
Single Phase
Three Phase
Single Phase Label
Note: If there is no AC-coupled battery connection, apply a spare label to the last module for 2nd solar connection or subboard if required.
Three Phase Label
Note: If there is no AC-coupled battery connection, apply the spare label to the last module for 2nd solar connection or subboard if required.
Testing of RCBO
Single Phase
Note: Test the device at regular intervals by pressing the Test button (marked T), following the intervals defined in your local regulations or monthly.
Three Phase
Note: Test the device at regular intervals by pressing the Test button
(marked T), following the intervals defined in your local regulations or
monthly.
How to Get the Latest Instruction Sheet
-
To get the latest instruction sheets for the device:
-
either scan the QR code on this document.
-
or search for the document references MX9K108PP or MX9K318PP on www.clipsal.com
-
Contact your local support to get a printed copy of the latest instruction sheet.
-
For more information, consult www.clipsal.com/support.
-
Clipsal by Schneider Electric (Australia) Pty Limited 33-37 Port Wakefield Road
-
Gepps Cross
-
South Australia 5094
-
Customer Care Centre
-
Tel: 13 73 28
Email: customercare.au@se.com -
Fax: 1300 369 288
-
Printed on recycled paper.
-
© 2024 Clipsal Australia Pty Ltd – All rights reserved.
-
The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>