camry CR 4083 Blender User Manual

camry CR 4083 Blender

PARTS

SAFETY CONDITIONS

IMPORTANT INSTRUCTIONS ON SAFETY OF USE
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2. The product is only for home use. Do not use the product for any purpose that is not compatible with its application.
3. The applicable voltage is 220-240 V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
4.  Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
5.  WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
9. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
11. Never use the product close to combustibles.
12. Do not let cord hang over edge of counter or touch hot surfaces.
13. Never leave the product connected to the power source without supervision.
14. For additional protection, it is advisable to install a residual current device (RCD) in the electrical circuit with a rated residual current not exceeding 30 mA. A specialist electrician should be consulted in this matter.
15. Do not insert fingers or any other objects into blender’s cup when the blender is on.
16.  In order to avoid injuries handle the blades carefully.
17. Watch out for long hair, scarves, neckties hanging above the cup and operating components of device.
18. For safety reasons use only original accessories and spare parts intended for particular blender type, available at authorised service center.
19.  Handle the blades with extreme care while disassembling accessories. The blades can cause cuts.
20. Change the accessories only when the device is switched off. Disconnect the device from the power.
21. Do not put any products other than food and liquids in the blender cup. Do not put hot products in the cup.
22. The device is not suitable for whipping egg whites, kneading dough or grinding meat.
23. Don’t use aggressive detergents to clean the housing, as it may remove the informational graphic symbols such as: scale, signs, safety marks, etc.
24. Do not start the empty mixing cup, without product inside.
25. MAXIMUM PERIOD OF CONTINUOUS BLENDER OPERATION IS 1 MINUTES. After 1 minutes of continuous operation stop the device and wait couple of minutes before restarting.
26. Do not pour hot liquids (over 60 ° C) into the cup.
27. If the blades become jammed, always unplug the power cord from the electrical outlet before removing the blockage.
28. Do not move the device while it is working.
29. Be careful when handling cutter blades, when emptying the bin and when cleaning.
30. Always disconnect the blender from the power supply when it is left unattended and before assembling, disassembling or cleaning.

DEVICE DESCRIPTION

1. Measurement cup (50ml)
2. Lid
3. Lid ring
4. Safety lock
5. Glass jug 1,5 liters
6. Blades
7. Motor base
8. Speed adjustment knob

DEVICE OPERATION

Before first use:

1. Remove all stickers from the motor base (7), jug (5) and lid (2) of the blender.

2. Wash the jug (5) and the lid (2) in warm water with washing-up liquid and dishcloth. Dry it in the inside and outside.

3. The blender is used to:
   a) blend fruits and vegetables – before blending, you must cut the food into 10-15mm slices.
   b) crushing the ice – the quantity of ice cubes in the glass jug should be about 10 pieces, and size of the ice cube should not exceed 302323mm.

4. Do not allow for continuous operation of the blender for longer than 1 minute. Later let the device cool down for 10 minutes.

5. Never use boiling liquids nor run the appliance empty.

6. Overfilling can block the operation. Please turn off the unit and pull out the plug from the power socket. Take some of the food out of the jug (5), then connect again to the mains. Device is ready for use.

ASSEMBLY

Jug assembly: seal ring, glass jug and blades are already assembled and ready to use. Measurement cup (1) and lid (2) must be set up before each use.

1. First, place the jug(5) on the motor’s base (7). Arrow symbol below the handle must point in to open padlock symbol (4). Turn the jug clockwise to the locked position (closed padlock symbol) (4).
2. Cover the jug (5) with the lid (2). Pull the lid using the lid ring (3) until it moves over the handle.
3. Place the measurement cup (1) into the lid (2). Turn the cup clockwise until its locked in the position.
   NOTE: Before each use you need to place the lid and the measure cup on the jug.
   NOTE: The jug assembly is not prepared to disassemble by the home user. Disassembling may break the safety lock feature (4). NOTE: Blender has a safety lock (4) feature. If the blender jug (5) is not properly assembled device will not operate.

HOW TO USE

1. Place assembled blender on stable, flat surface.

2. Make sure the speed adjustment knob (8) is set to the OFF position (“0”).
   Knob marking:
   0 – OFF: turn off the unit.
   1 – Low speed: suitable for soft food blending.
   2 – High speed: suitable for hard pieces of food.
   P – Pulse: suitable for short-time blending (a few seconds). Use it if some of the food pieces are too hard to blend, or stuck.
   When you move the knob to the pulse setting, blender runs at its highest speed as long as you keep pushing it. Recommended to use for ice crushing.
   NOTE: To crush the ice move the knob to “P” position for about 1 second, and then wait at least 2-3 seconds before repeat.

3. Place assembled jug (5) on the motor base (7).

4.  Remove the lid (2) from the blender jug (5), put the ingredients in for mixing. In order to avoid overflow, the level of ingredients in the jug (5) should not exceed ¾ of jug’s height. Close the lid (check ASSEMBLY point 2 for the details).

5. Connect the power plug to the power outlet.

6. Turn the device on by rotating speed adjustment knob (8) to chosen speed.
   NOTICE: During operation always hold the jug (5) with a hand.

7. When the mixed products have proper consistence, turn the device off by rotating speed adjustment knob (8) to the OFF position. Wait until the blades stop moving. Remove the power plug from the power socket. Remove the lid.

CLEANING AND MAINTENANCE

Make sure that the device is disconnected from the power.

1.  Fill the jug with water to half of its volume. Add a few drops of dishwashing liquid.
2. Turn speed adjusting knob to ON, then push the Pulse knob several times in a row.
3. Remove the jug (5) from the motor base (7), empty and rinse under running water.
4. Set aside to dry.
5. Clean the motor base (7) with moist cloth, and then wipe dry.
   NOTICE: Don’t immerse motor base (7) in water or other liquids.
   NOTICE: Do not wash any blender parts in dishwashers.

TECHNICAL DATA
Power: 1000W
Max. Power: 2200W
Voltage: 220-240V~ 50/60Hz
Recommended operation time: max 1 minute turned on + 10 minutes turned off.

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit
its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>