ION IPA150X Bluetooth Speaker User Guide
- June 6, 2024
- ION
Table of Contents
ION IPA150X Bluetooth Speaker User Guide
Box Contents
- Explorer XLTM
- Power Cable (IEC320 C13, 6 ft./182 cm)
- Microphone with Cable (8 ft./250 cm)
- Quickstart Guide
Note: Before you first use the product, please fully charge the battery. Your unit was purposely shipped with a reduced battery charge to ensure safe transit. For optimal charging, power off the speaker while charging.
Features
- A. Display: Shows information relative to the current operation.
- B. Control Knob: Press to toggle between controlling the volume of the music source (Bluetooth, Aux, or Radio), mic input, or instrument input/FX, or the Treble and Bass EQ, as indicated on the display. Turn the knob to increase or decrease the selected setting.
- C. Power: Press and hold to turn Explorer XL on or off.
- D. Bluetooth: Press to pair to a Bluetooth device or disconnect a paired Bluetooth device and enter Aux mode. Press and hold to turn voice prompts on or off.
- E. Link: Press and hold this button to start stereo linking to another Explorer XL. Then, repeat this process on another compatible speaker. To disconnect the link between the two speakers, double-press the Link button. See the full User Guide for more detailed instructions.
- F. BOOM: Press to simultaneously enhance the bass EQ and volume and activate a light show that pulses to the beat of the music.
- G. RADIO: Press to set the radio to FM1 or FM2, or turn the radio off.
- H. Presets: In Radio Mode, press these buttons to select a previously saved preset station. To save the current station as a preset, press and hold these buttons.
- I. Tune/Track: Press to tune in a radio station or go to the previous/ next track on a Bluetooth connected device. To “seek” (jump to the next available radio station), hold either button down for a few seconds.
- J. Play/Pause: Press to play or pause a track from a connected Bluetooth device.
- K. Lights: Press to cycle between light modes.
- L. FX REC: Press to record up to 30 seconds of your own sound effect. Once the REC icon begins flashing, press and hold an FX pad to begin recording from any sound source (such as Bluetooth, radio, or the Inputs) while the pad is held. Once recorded, press the FX pad to trigger your sound. Press and hold this button and press an FX pad to delete a recorded sound. See the full User Guide for more detailed instructions.
- M. FX SELECT: Press to change the sounds on each FX Pad. Once the FX Pads are lit white, press each one to cycle through all the sound effects. Once you have found the sound effects you like, press this button again to lock them in. To revert to the default sounds, press and hold this button.
- N. FX Pads: Press these pads to trigger a sound effect. Press the Control Knob and select INST to adjust the FX volume.
- O. Microphone Input (1/4” [6.35 mm], unbalanced): Press the Control Knob and select MIC to adjust the microphone volume.
- P. Instrument Input (1/4” [6.35 mm], unbalanced): Press the Control Knob and select INST to adjust the instrument volume.
- Q. Aux Input (1/8” [3.5 mm], balanced): To hear this signal, disconnect Bluetooth and enter Aux Mode by pressing the Bluetooth button.
- R. USB Charging Port: Connect your device’s charge cable here to charge it. USB charging only functions when the unit’s power is turned on.
Bluetooth Connecting with Explorer XLTM
-
Power on the Explorer XLTM by holding down the Power button for 2 seconds. Explorer XLTM will automatically enter Bluetooth pairing mode indicated by the Bluetooth icon flashing blue.
-
Navigate to your device’s Bluetooth setup screen, find Explorer XL, and connect. When connected, the Bluetooth icon in the display will be lit solid blue and you will hear “Connected”.
Note: Do not connect to Explorer XL_BLE; this is reserved exclusively for connecting to the ION Sound XP app. If you experience trouble in connecting, select “Forget this Device” on your Bluetooth device and try to connect again. -
To disconnect, turn off Bluetooth from your device’s Bluetooth settings, or press the Bluetooth button. This will also enter Aux mode.
App Control
IMPORTANT: To ensure the best possible experience with the app, use the most current Android OS or iOS on your device.
Follow these steps to download the free app on your device:
- Open the Apple App Store or Google Play on your device. Then, search for the ION Sound XPTM app.
- Follow the on-screen instructions to download and install the app. Once downloaded, the ION Sound XPTM app will appear on your device’s home screen.
- Connect your device to Explorer XLTM via Bluetooth. See the Bluetooth Connecting with Explorer XLTM to learn how to do this.
- Open the ION Sound XPTM app and tap to select Add A Product on the screen. The app will scan and find Explorer XLTM.
- Select the Explorer XL icon to go to the next screen, where you can control the speaker settings from your device.
Outdoor Use and Care
Though Explorer XLTM is water-resistant and able to tolerate splashing water, please review these tips to get the best performance from Explorer XLTM: Bring Explorer XLTM indoors during extreme cold, heavy rain, or melting snow. Please do not place Explorer XLTM in standing water. Please do not connect the power cable to Explorer XLTM in a wet environment. Keep any non-water-resistant devices (phones, music players, etc.) in a dry place where they will not be affected by water and cause a risk of electric shock. Make sure the charging port door is securely closed when using outdoors to ensure the IPX5 rating.
Technical Specifications
- Output Power: 220 W (peak)
- Drivers: 1 x 8″ (203.2 mm), 2 x 3” (76.2 mm), 2 x 1” (25.4 mm)
- Frequency Response: 35 Hz – 15 kHz
- Bluetooth:
- Profile: A2DP, AVRCP
- Range: Up to 100 ft. (30 m) from source device. (Bluetooth range is affected by walls, obstructions, and movement. For optimal performance, place the product it is unobstructed by walls, furniture, etc.)
- Linked Range: Up to 65.6 ft. (20 m) between speakers
- Water Resistance Class: IPX5
- Battery: Sealed lead-acid
- Battery Life: Up to 120 hours (Battery life may vary based on temperature, age, and volume use.)
- Recharge Time: Up to 10 Hours
- Dimensions(WxDxH): 15.4″ x 10.9″ x 18.9″ / 392 x 278 x 480 mm
- Weight: 24.9 lbs. / 11.3 kg
Specifications are subject to change without notice.
Safety Information
Important Safety Instructions
-
Read these instructions. Keep these instructions. Heed all warnings. Follow all Instructions.
-
Do not use this apparatus near water.
-
Do not block any ventilation openings (if applicable). Install in accordance with the manufacturer’s instructions. Do not install this equipment in a confined or “boxed-in” space such as a bookcase or similar unit, and maintain good ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place exposed flame sources such as lighted candles on the apparatus.
-
Do not defeat the safety purpose of the polarized or grounding-type plug (if applicable). A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Only use attachment/accessories specified by the manufacturer.
-
Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus (if applicable). When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
Internal/External Voltage Selectors (if applicable): Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself.
-
Power Sources (if applicable): This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit.
-
Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries (a battery pack or an installed battery) shall not be exposed to excessive heat such as sunshine, fire, etc.
-
(If applicable) Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
-
Warning (if applicable): Provide an earthing connection before the mains plug is connected to the mains. When disconnecting the earthing connection, be sure to disconnect it after pulling the mains plug out from the mains.
-
For Class II apparatus only (if applicable): This symbol means the equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
-
Class II Wiring (if applicable): To reduce the risk of electric shock, the external wiring connected to the terminals with “Class II Wiring” requires Class II wiring installed by an instructed person or the use of ready-made leads or cords.
-
This apparatus is for professional use only. Intended operational climate: moderate.
-
(If applicable) When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Be careful not to damage the power cord.
Before using it again, make sure the power cord has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer. -
Warning (if applicable): Excessive sound pressure (high volumes) from headphones can cause hearing loss.
-
Warning (if applicable): Please refer to any important information (e.g., electrical, safety, etc.) printed on the exterior bottom enclosure or rear panel before installing or operating the product.
-
Warning (if applicable): Terminals marked with the lightning bolt symbol may be of sufficient magnitude to constitute a risk of electric shock.
-
Minimum distances 10 mm around the apparatus for sufficient ventilation.
Safety Notices
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER.
NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
DANGEROUS VOLTAGE: The
lightning flash with arrowhead symbol within the equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
INSTRUCTIONS: The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this appliance.
WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.
NOTICE CONCERNING FCC REGULATIONS: You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (a) reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d) connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where appropriate; (f) consult the dealer or an experienced radio/television technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
If apparatus contains a coin/button-cell battery: Warning: Do not ingest the battery—chemical burn hazard. The remote control supplied with this product contains a coin/button-cell battery. If the coin/button-cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. Tell others about the risk associated with button batteries and how to keep their children safe. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.
Disposal of Batteries (if applicable):
-
Never dispose of any types of batteries in fire or near excessive heat or direct sunlight. Overheated batteries can rupture or explode.
-
If you are unsure of how or where to dispose of a battery, refer to your local ordinances for the proper location, method, etc.
-
Alkaline batteries & lithium button cell batteries: You can safely dispose of alkaline and lithium button cell batteries with normal household waste.
They do not pose a health or environmental risk during normal use or disposal. (Alkaline batteries are composed primarily of common metals like steel, zinc, and manganese.)
Do not dispose of large amounts of alkaline or lithium button cell batteries in a group. Used batteries are often not completely “dead.” Grouping them together can bring these “live” batteries into contact with one another, creating safety risks. To avoid this, insulate each battery with tape or other nonconductive material to ensure it does not discharge. Proven cost-effective and environmentally safe recycling processes are not yet universally available for alkaline and lithium button cell batteries. Some communities offer recycling or collection of these batteries. For more information, refer to your local ordinances or contact your local government. -
Lead-acid batteries: Dispose of lead-acid batteries by bringing them to an electronic waste center or recycling center, or dispose of them in accordance with your local ordinances. (Rechargeable lead-acid batteries are the same type used in automobiles and should be disposed of in a similar fashion.)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20 cm between the radiator & your body.
Service Instructions
- Disconnect power cord before servicing.
- Replace critical components only with factory parts or recommended equivalents.
- For AC line powered units: Before returning repaired unit to user, use an ohmmeter to measure from both AC plug blades to all exposed metal parts. The resistance should be more than 2,000,000 ohms.
Trademarks and Licenses
ION Audio is a trademark of in Music Brands, Inc., registered in the U.S. and other countries. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. Android and Google Play are registered trademarks of Google Inc.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by ION Audio is under license. All other product names, company names, trademarks, or trade names are those of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>