Qolsys IQ Outlet Plug In Switch User Guide
- June 6, 2024
- Qolsys
Table of Contents
Qolsys IQ Outlet Plug In Switch User Guide
This product speaks with other Z-Wave certified devices
INTRODUCTION
IQ Outlet is a Z-Wave Plus® certified device with S2 security and SmartStart features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and SmartStart. IQ Outlet is a member of the Z-Wave™ family and communicates with other Z-Wave certified devices in a control network. It can be used to turn On or Off lamps or AC operated appliances as well as monitor the energy consumed. Each Z-Wave device also serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range. Different types and brands of Z-Wave devices can be associated with IQ Outlet in your system and they will work together to optimize and expand the coverage of your Z-Wave network.
FEATURES
- Turns ON/OFF incandescent, CFL, or LED lamps, and AC operated appliances
- 700 Series Z-Wave module
- Energy monitoring supported
- LED to indicate ON/OFF status
- Remotely or manually turns ON or OFF lights
- Controls appliances up to 15A
- Z-Wave Plus Certified with S2 security and SmartStart (QR code on bottom of device)
- Grounded 3-pin AC power receptacle to enhance safety
- Safety tab to secure unit to AC outlet
- Compact design – does not block the 2nd AC outlet
- Over-The-Air firmware upgrade available, if supported by controller
- Supports Network Wide Inclusion (through a repeater), if supported by controller
- Functions as a Z-Wave signal repeater
! WARNING !
RISK OF FIRE, ELECTRICAL SHOCK & BURNS
DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENT
No user serviceable parts are in this module
To reduce the risk of electric shock, this product has a grounding type plug
that has a third (grounding) pin. This plug will only fit into a grounding
type power outlet.
If the plug does not fit into the outlet, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
The appliance connected to this Z-Wave module must not exceed 900W
incandescent, 200W CFL/LED, ½ horsepower motor and 15A, 1800W resistive load.
SETUP
Step 1: Plug in the AC power plug of the appliance to the receptacle of
IQ Outlet.
Step 2: Insert the module’s 3-pin plug into an AC outlet in the same room
as your gateway.
Step 3: Inclusion/Exclusion: Add or remove the device into your network by a Z-Wave certified controller. IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on adding or removing devices to/from the network. You should be able to add IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the traditional method for Z-Wave as follows:
-
Place your network controller into inclusion mode by following the controller manufacturer’s instructions.
-
When the controller is ready, single click the button on the top of the IQ Outlet.
The controller should indicate that the new device was added successfully. -
Once IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.
If the controller shows it failed, repeat the procedure.
Manual Reset
Please use this procedure only when the network primary controller is missing or otherwise inoperable. The manual reset method is as follows:
-
Unplug IQ Outlet from the AC outlet and also unplug the power plug of the appliance from the IQ Outlet (if plugged in).
-
Press and hold the button on IQ Outlet.
-
Plug IQ Outlet back into the AC outlet with the button pressed.
After 3 seconds, release the button. If you see the LED blink, that means that IQ Outlet has been reset successfully and you may retry Step 3 in Setup to add the module into your network. Otherwise, please repeat the manual reset procedure
Note: If IQ Outlet was previously Added (Included) in your network, reseting it locally does not mean it has been removed from your controller software. If you wish to remove the IQ Outlet from your controller software you will need to remove (Exclude) the module from the network by your controller. If IQ Outlet is removed from the network supporting S2 security, the only way to add the device back into the network is using the QR code or the DSK code. Therefore, please store the QR code on the product as well as copy of the full DSK printed on the package in a safe location.
Use the manual reset procedure only in the event that the network primary controller is lost or otherwise inoperable.
BASIC OPERATION
The connected appliance can be controlled manually with a push button or wirelessly via the software from your controller.
A Z-Wave certified controller is capable of settng up this product in your desired network. Once the device is added, you may assign it to a group. Please refer to the instructions manual of your controller for details and procedures on how these settings can be done.
In the event of a power failure, the device will return to the last setting after the power is restored (refer to Advanced Configuration section to change the default).
About the push button:
There is a single button on IQ Outlet for manual operation that:
- Manually turns the connected lighting ON/OFF by pressing the button. It functions as a toggle switch.
- Adds (Includes) or Removes (Excludes) your IQ Outlet to/from your Z-Wave network. Please refer to the instructions manual of your gateway or remote controller for detail procedures on how these actions can be done.
Energy Monitoring:
This device supports energy monitoring and it is expressed in kWh and Watts.
ADVANCED CONFIGURATION
Configurable Parameter Settings: If your controller supports Z-Wave configurable parameters, the following settings can be modified.
Parameters
#
| Description| Values| Default|
Bytes
3
| LED Mode Indicator|
- When value = 0, the LED indicator will be OFF when the connected appliance is ON, and the LED indicator will be ON when the connected appliance is OFF.
- If value = 1, the LED indicator will be OFF when the connected appliance is OFF, and the LED indicator will be ON when the connected appliance is ON.
- If value = 2, the LED indicator will be always OFF regardless of the load status.
|
0
|
1
4
|
Energy monitoring reporting interval
| 0 = Disable energy monitoring (default) 1 – 255 = Reporting interval (minutes)|
0
|
1
Depending on the capability of your controller or gateway software, the following simple to advanced operations can be performed. Please refer to the controller’s or gateway manual for details.
Association:
- IQ Outlet supports Group 1 for lifeline communication and Group 2
- You can associate five Z-Wave devices to Group 1.
- Lifeline association only supports the “manual reset” event.
- For instructions on how to “set lifeline associate”, please refer to your controller/ gateway instructions.
- You can associate five Z-Wave devices to Group 2.
- The devices in Association Group 2 can be controlled (on/off) by single pressing the button using Basic Set
SPECIFICATIONS
Model
| PS700
---|---
Input power|
120 VAC, 60 Hz.
Max output loading
| 900W incandescent, 200W CFL/LED, ½ horsepower motor and 15A, 1800W
resistive load
Radio frequency|
908.4/916 MHz.
Wireless range
| 279ft Outdoor line of sight
Normal operating temperature|
32°F – 104°F (0°C – 40°C)
FOR INDOOR USE ONLY
Interoperability with Z-Wave devices
A Z-Wave network can integrate devices from various classes of products, and
these devices can be made by different manufacturers. The product introduced
in this instruction manual has a Z-Wave certification which allows such an
interoperability.
SUPPORTED COMMAND CLASSES
Description
| Version| Security Class
---|---|---
COMMAND_CLASS_ZWAVEPLUS_INFO| v2|
COMMAND_CLASS_SWITCH_BINARY
| v2| S2
COMMAND_CLASS_METER| v6|
S2
COMMAND_CLASS_CONFIGURATION
| v4| S2
COMMAND_CLASS_SCENE_ACTIVATION| v1|
S2
COMMAND_CLASS_SCENE_ACTUATOR_CONF
| v1| S2
COMMAND_CLASS_ASSOCIATION| v2|
S2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
| v3| S2
COMMAND_CLASS_ASSOCIATION_GRP_INFO| v3|
S2
COMMAND_CLASS_TRANSPORTSERVICE
| v2|
COMMAND_CLASS_VERSION| v3|
S2
COMMAND_CLASS_MANUFACTURER_SPECIFIC
| v2| S2
COMMAND_CLASS_DEVICE_RESET_LOCALLY| v1|
S2
COMMAND_CLASS_INDICATOR
| v3| S2
COMMAND_CLASS_POWERLEVEL| v1|
S2
COMMAND_CLASS_SECURITY_2
| v1|
COMMAND_CLASS_SUPERVISION| v1|
COMMAND_CLASS_APPLICATION_STATUS
| v1|
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5| v5|
S2
FCC ID: 2AMY9PS700
Supplier’s Declaration of Conformity
47 CFR 2.1077 Compliance Information
Model: PS700
Responsible Party – US Contact Information
Qolsys, Inc.
1900 The Alameda Suite 420
San Jose, CA 95126
United States
intrusion-support@tycoint.com
FCC Compliance Statement (Products subject to Part 15)
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or changes to this
equipment. Such modifications or changes could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
IC: 22968-PS700
This device complies with Part 15 of the FCC Rules and with RSS of Industry Canada. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Z-Wave is a registered trademark of Silicon Labs.
WARRANTY
Qolsys warrants to the original purchaser of this product that for the warranty period, this product will be free from material defects in materials and workmanship.
The foregoing warranty is subject to the proper installation, operation and maintenance of the product in accordance with installation instructions and the operating manual supplied to customer.
Warranty claims must be made by customer in writing within 30 days of the
manifestation of a problem. Qolsys’ sole obligation under the foregoing
warranty is to repair, replace or correct any such defect that was present at
the time of delivery or during the warranty period. The warranty does not
extend to consequential or incidental damage to other products that may be
used with this product. For inquiry and customer service, email intrusion-
support@tycoint.com.
All brand names shown are trademarks of their respective owners.
Warranty period: limited 1 year from date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>