MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System Instruction Manual

October 27, 2023
MB QUART

MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned
System logo

MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned

System

MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
productBefore you begin, read through these instructions and check that all parts are present. Always disconnect negative battery terminal prior to installation. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation.

Parts List

No.| Component Name| Qty
1| 10” Subwoofer w/Enclosure (MBQRG-SUB-1)| 1
2| NA2-400.1 Amplifier| 1
Tools Required

1| Bojo Tool
2| Panel Clip Pliers
3| 1/8” Drill Bit
4| Drill
5| T25 Torx Bit
7| 10mm Socket
8| Rachet

Disassembly

  • Remove hood by turning two latchesMB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 01

  • Remove four push pins from the passenger side center console
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
02

  • Remove five push pins from the driver side center console
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
03

  • Remove underseat tray from passenger sideMB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 04

  • Lift center console upward starting at cupholder and remove from vehicle
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
06

Harness Installation

  • Route the subwoofer extension harness extension harness from the middle of the dash out the grommet toward the front of the vehicleMB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 07

  • Pass the wires from the grommet to the radiator cap opening (if other wire present zip tie along)
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
08

  • Pass the wiring around any moving parts and down the frame toward the center console and secure in place with zip ties
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
09

  • Run along air intake securing with zip ties to the power bus bar harnessMB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 10

  • Route subwoofer harness to the passenger side of the battery MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 11

  • Drill 1.25” hole and pass subwoofer connection through hole and place grommet MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 12

Amplifier Adjustment

Adjust the NA2-400.1 amplifier’s gain and crossover settings as picturedMB
QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
13 Note
Turn Gain all to the last “L” on Level HPF to 100Hz going just past “P” on LP LPF Subsonic set to 35Hz going to “S” on Subsonic Boost 0dB

Amplifier Installation

  • Plug in power harness pigtail to amplifier and make appropriate power, ground, and remote connections
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
14

  • Connect the subwoofer extension harness to the NA2-400.1 amplifier harness
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
15

  • Connect RCAs to the NA2-400.1 amplifier from your source unit
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
16

Subwoofer Installation
  • Drill three 1/8” holes at marked indents in floor (only drill deep enough to get through first layer of material)MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 17
  • Place subwoofer enclosure under passenger seat and secure with three high-low T25 Torx screws and washers

Note
Use two picks to align enclosure with holes in vehicle and also use provided bit extension to reach rear screw where the arrow is MB QUART MBQRG-SUB-1
400 Watt Polaris RANGER Specific Subwoofer Tuned System
18

  • Connect the subwoofer enclosure harness to the subwoofer extension harness MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 19
Reassembly
  • Place center console in the vehicle sliding forward then downMB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System 20

  • Insert four push pins on passenger side console
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
21

  • Place five push pins on driver side center console
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
22

  • Place battery cover into place
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
23

  • Turn vehicle and radio on and enjoy the music
    MB QUART MBQRG-SUB-1 400 Watt Polaris RANGER Specific Subwoofer Tuned System
24

FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty period. Components that prove to be defective in materials and workmanship under proper installation and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith. To view the full warranty, please visit the website. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use such marks by MB Quart is under license.
All product names, logos, and brands are property of their respective owners. All company, product and service names used in this literature are for identification purposes only. Use of these names, logos, and brands does not imply endorsement.
©2021 Maxxsonics USA, Inc.
MBQuart products are designed and engineered in the USA by

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MB QUART User Manuals

Related Manuals